User's Manual

Striker
Please pay attention to the striker before filling the missiles: The launcher bracket should be in a fully lowered state.
If it is not lowered, press the “I” button on the remote control to lower it (see the manual for details).
The striker at the bottom of the launcher's cartridge should be hidden. If the striker is extended, use the F
button on the remote control to retract it.
Failure to retract the striker will aect the filling and launch of the missile. Do not use deformed or damaged missiles.
The launcher's launch port is oriented in the same direction as the attack center. Align the slots on the base
and insert and mount the missile launcher in place.
Place the launcher above the base
Load the missiles into the
cartridge as shown in the figure
Load the seat down into
the launcher base
Complete
Launcher Loading
Start switch
Fault
Cause
Solution
Cannot fire bullets
The missile is stuck, and the
launcher is not installed correctly
Refer to the manual for how to
fill and launch. Remove and reinstall
the missile launcher in place.
Replace the battery. Refer to the
manual to understand how to match.
Refer to the manual to find out
how to properly install the armor.
The battery is dead and
needs to be rematched
Armor is not installed correctly
Not in combat mode
Turn the switch to "ON"
Replace the battery.
Low battery
The robot cannot match
the remote control
Armor doesn't bounce
o after being hit
The attack center is not
working properly
The robot's LED indicator flashes
alternately red and green
Forward
Backward
Lower bracket
Sight
Automatic
presentation
LED indicator
Turn the head
Launch missile
Raise bracket
Rotation alert
Attack Center Installation
Combat Mode
Farthest attack distance
Precise aiming
How to avoid stuck missile
What to do after stuck missile
Combat Life
Infrared Installation
ONEMARS Hexapod Battle Robot User Manual
Read this manual carefully before use, and retain it for future reference
Launcher Installation
Launcher Bracket Installation
The launcher bracket is inserted down to the bottom at the
notched portion of the top side. The top surface of the
inserted launcher bracket should be aligned with the top
surface.
Proper installation will allow the hook at the bottom of
the center to be properly connected to the sensor
switch. When the attack center is not installed, the
hook is loose. When installing, fasten the hook toward
the front end of the attack center.
Shooting skills need to be improved through practice.
To hit the opponent's sight, you can start by aiming at
the sticker. When playing against a master, the novice
can compensate for the dierence in attack ability by
practicing stickers.
Each time it hits the sight, the robot shudders and an LED indicator goes o to indicate that it has been
hit. After being hit three times, it will automatically shut down and exit the battle with failure.
To rejoin the combat, you need to restart the battle robot.
Power saving mode: If it is not operated within 5 minutes, it will automatically shut down.
Press and hold the remote control F button, the missile will continuously launch until it is completely used
up. The missile will shoot at a greater distance. For a single launch of a missile, you need to master the
skills and timing. Press the F button and the motor starts to run, driving the weapon system to complete a
series of related launch actions. The striker impinges the missile into the front-end turbine, which then
spins the missile out. The key to shooting the missile farthest is to seize the opportunity. Press and hold the F
button, and release it until you hear a click of the striker. In this way, the motor will reach the maximum
speed, and the striker can be quickly retracted after being extended. In the case that the button pressing
time is too short, the motor does not reach the maximum speed, and the missile does not shoot too far. In
the case that the button pressing time is too long, the striker has entered the second launching round, and
the next time the launch is made, the motor will not reach the maximum speed when the striker pushes the
missile toward the turbine, and the missile will not shoot too far. In extreme cases, the striker starts to push
out the missile just as the motor is grinding to a halt, which can cause stuck missile. As for the solution of
stuck missile (see the manual), after a lot of practice, you can learn to catch the sound made by the striker
and master the best launch time.
The D button on the remote control is used to adjust the horizontal launching direction of the missile, and
the I and H buttons are used to adjust the elevation angle of the vertical launching of the missile. The
launching direction and elevation angle of the missile can be slightly adjusted by gently pressing the D, I
and H buttons.
Electronic components must not be removed. When not using the product for a long time,
remove the battery from the battery case.
Do not place this product near heat sources, sources of ignition, and locations where the
temperature is above 60°C.
Do not short-circuit this product.
Do not subject this product to severe impact.
Do not expose to the sun. Wipe with a wet cloth to keep clean and dry.
Periodically inspect its wires, plugs, enclosures and other components for damage. When
any damage is found, stop using it until it is completely repaired.
The product contains smaller parts and is not suitable for children under 3 years of age.
Keep away from crowd.
Do not shoot people or animals.
Do not use near the ear.
Use only the product's original projectiles.
Do not point your face at the projectile launch port at any time.
Laser radiation, do not look directly at the beam.
Please keep this manual for future reference.
First, please refer to the detailed instructions in the manual to properly fill the missile. Second, master the
timing of the launch. The correct filling of the missile and the good timing can minimize the occurrence of
stuck missile.
Product name: ONEMARS hexapod battle robot Model: OMSLR24AIQI
Material: ABS, PC Ages: 5 and up
Input voltage: 4.8V
Input current:3A
Wireless connectivity: 2.4GHz
Storage temperature: -20℃ ~ 45℃ (-4℉ ~ 113℉)
Operating temperature: -10℃ ~ 45℃ (14℉ ~ 113℉)
After pressing the F button, the missile launcher does not respond (no running sound), it may be stuck
missile: Press the I button to fully lower the launcher bracket, remove the missile launcher, remove all the
missiles, and repeat the loading procedure.
Make sure that the batteries are installed in both the robot and the remote control and they are all
activated. The match takes 2-3 seconds. The indicator on the remote control will continue to flash until
the remote control indicator is o and the frequency match is complete. It can match up to 20 robots in
the same field of battle, and more than 20 robots in the same field may cause signal interference.
After completing the frequency match, you can join the battle. If the robot does not respond to the remote
control, turn o the power of the remote control and the robot, re-open the start switch to "ON", and
re-match (steps are the same as above).
Follow the steps above to even match multiple robots to one remote control. Bring you an extraordinary
experience of the robot army! Repeat the above steps to re-match the robot to the original remote control.
Robot start: Turn the robot's switch to "ON" to turn
on the power
Remote control start: Turn the remote control's
switch to "ON" to turn on the power
Manufactured by: Beijing AIQI Technology Co., Ltd.
Address: Room 1203, Block D, No. 9/11 Shangdi 3rd St., Haidian District, Beijing - 100085, China
For further information, please go to www.iqi-inc.com
Align the bottom of the infrared ray with the
launcher hook and fasten it downward.
Press the armors into the slots to install them in place
The outer armors and inner armors are installed
There are a total of 6 inner armors, including 3 small inner
armors and 3 large inner armors. Large and small inner
armors are installed in the horizontal section of the larger and
smaller legs, respectively. There are a total of 6 outer armors
installed in the vertical section of the legs.
Armor Installation
Note: When the robot moves slowly and the remote control is not sensitive,
it indicates that the batteries are low and need to be replaced.
Proper Installation of Remote Control
This product needs to be powered by four AA batteries; non-rechargeable batteries cannot be charged;
the charging time of the rechargeable battery is about 3 hours; the rechargeable battery can only be
charged under adult supervision; the rechargeable battery should be taken out of the product before
charging; dierent types of batteries or old and new batteries should not be mixed; the power supply
terminal must not be short-circuited; the battery should be placed in the correct polarity; and the used
battery should be removed from the product.
Use a cross screwdriver to loosen the battery cover, correctly insert two
1.5V AA non-rechargeable batteries (included) according to the positive
and negative signs, put back the battery cover and tighten the screws.
1. Use a cross screwdriver to
loosen the battery cover
2. Open the battery cover
from the right edge
3. Install the positive and negative
signs to properly place the battery
4. Put back the battery cover
and tighten the screws
USB Charging
Cable (supplied)
1. The LED light is always on when connected; 2. The LED light flashes
slowly when charging; 3. The LED light is o when fully charged;
(When the LED light flashes quickly, the charging fails. Please check the
circuit and reoperate the charging procedure.)
USB Charging
Plug
Robot Charging
Socket
Mode 1: Connect to a
computer USB for charging
Mode 2: Connect to a USB
adapter for charging
Mode 3: Connect to a mobile
power bank for charging
Robot Battery Use
Sticker × 1
Infrared × 1
Battery Cover × 1 Armor × 6 Remote Control × 1
Launcher Base × 1 Launcher
Bracket × 1
Large Inner
Armor × 3
Small Inner
Armor × 3
Body × 1 Robot Head × 1 Missile
Launcher × 1
Missile × 12
Attack Center/Infrared Installation
Launcher Bracket/Launcher Installation
Battery Installation
Equipment List
Start the Robot/Remote Control
Robot and Remote Control Frequency Matching
Equipment List
Missile launch
Specifications
Troubleshooting
Precautions
Robot Gameplay
FCC Statement
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) This device may not cause harmful interference,
and(2) This device must accept any interference received, including interference that may cause undesired
operation.
Attention that changes or modification not expressly approved by the party responsible for compliance-
could void the user's authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential isnallation. This product generates, uses, and can radiate radio
frequency energy and, if not installed and used in acordance with the instructions, may cause harmful
interference to radio communications, However, there is no guarantee. that interference will not occur in a
particular insallation. If this product does cause harmful interference to radio or television reception, which
can be determined by turning the equipment o and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
—Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit diferent from that to which the receiveris connected.
—Consult the dealer or an experienced radio/TV technician for help.
This equipment should be installed and operated with a minimum distance 20cm between the radiator and
your body.
FCC ID：2ALJ6-OMSLR24AIQI
FCC ID：2ALJ6-OMC01AIQI
Note: Give four 1.2V rechargeable batteries for free.
-WARNING：This product contains a Button or Coin Cell Battery. A swallowed Button or Coin Cell Battery
can cause internal chemical burns in as little as two hours and lead to death. Dispose of used batteries
immediately. Keep new and used batteries away from children. If you think batteries might have been
swallowed or placed inside any part of the body, seek immediate medical attention.”