Version 1.
EURORACK UB1222FX-PRO IMPORTANT SAFETY INSTRUCTIONS DETAILED SAFETY INSTRUCTIONS: 1) Read these instructions. 2) Keep these instructions. 3) Heed all warnings. 4) Follow all instructions. CAUTION: WARNING: To reduce the risk of electric shock, do not remove the top cover (or the rear section). No user serviceable parts inside; refer servicing to qualified personnel. To reduce the risk of fire or electric shock, do not expose this appliance to rain and moisture.
EURORACK UB1222FX-PRO EURORACK Ultra Low-Noise Design 16-Input Mic/Line Mixer with Premium Mic Preamplifiers, FBQ Feedback Detection System and 24-Bit Multi-FX Processor s 4 new state-of-the-art, studio-grade IMP Invisible Mic Preamps with: - 130 dB dynamic range for 24-bit, 192 kHz sampling rate inputs - Ultra-wide 60 dB gain range - Lowest possible distortion 0.
EURORACK UB1222FX-PRO FOREWORD TABLE OF CONTENTS Dear Customer, Im sure youre one of those people who have devoted themselves body and soul to your chosen area and no doubt this has transformed you into an expert in your field! Well, for over 30 years, my passion has been music and electronics. This not only led me to establish BEHRINGER, but also enabled me to convey and share my enthusiasm with my employees.
EURORACK UB1222FX-PRO This way, what once used to be a labor-intensive search for feedback frequencies is now an activity that even a child could master. Frequency response correction Using the equalizers found in each channel strip, you can simply, quickly and effectively adjust the way a signal sounds.
EURORACK UB1222FX-PRO 1.3.2 Initial operation Be sure that there is enough space around the unit for cooling purposes and to avoid over-heating. Please do not place your mixing console on high-temperature devices such as radiators or power amps. The console is connected to the mains via the supplied power cable. The console meets the required safety standards. Blown fuses must only be replaced by fuses of the same type and rating. + + Please note that all units must be properly grounded.
EURORACK UB1222FX-PRO and lower band are 12 kHz and 80 Hz respectively. The mid band is configured as a peak filter with a center frequency of 2.5 kHz. Unlike shelving filters, the peak filter processes a frequency range that extends upwards and downwards around its middle frequency. 2.1.4 Pan, mute switch and channel fader 2.1.3 Aux sends (MON and FX) Fig. 2.
EURORACK UB1222FX-PRO 2.2 Stereo channels are, so to speak, collected from one point on each of the channel strips and then routed to the main section all together. 2.2.1 Channel inputs 2.3.1 Monitor send and FX send channels Fig. 2.5: Stereo channel inputs Each stereo channel features two line-level inputs on 1/4" connectors for left and right channels. Channels 9/10 and 11/12 can also be used in mono if you only use the connector labeled L. Fig. 2.
EURORACK UB1222FX-PRO 2.3.2 Monitor send and FX send connector Fig. 2.7: Aux send connectors MON and FX MON SEND Connect the input of your monitor power amp or an active monitor system here to make the monitor mix audible to the musicians on the stage. The signal mix is created using the channels MON controls. FX SEND The FX SEND connector outputs the signal you picked up from the individual channels using the FX controls.
EURORACK UB1222FX-PRO Live PA systems: A stereo dynamics processor (optional), stereo equalizer (optional) and the stereo power amplifier for full-range loudspeakers with passive crossovers. Fig. 2.10: 2-track connectors CD/TAPE INPUT The CD/TAPE INPUT RCA connectors are provided for connecting a 2-track machine (e.g. DAT recorder) or also a CD player. They can also be used as stereo line input. Alternatively, the output signal of a second EURORACK or BEHRINGER ULTRALINK PRO MX882 can also be connected.
+ EURORACK UB1222FX-PRO Connect microphones before you switch on the phantom power supply. Please do not connect microphones to the mixer (or the stagebox/ wallbox) while the phantom power supply is switched on. In addition, the monitor/PA loudspeakers should be muted before you activate the phantom power supply. After switching on, wait approx. one minute to allow for system stabilization. LEVEL METER/CLIP The high-precision level meter accurately displays the appropriate signal level.
EURORACK UB1222FX-PRO 3. DIGITAL EFFECTS PROCESSOR AND XPQ SURROUND FUNCTION 3.
EURORACK UB1222FX-PRO Fig. 4.1: 1/4" TS footswitch connector 4.2.1 Audio connections Please use commercial RCA cables to wire the 2-track inputs and outputs. You can, of course, also connect unbalanced devices to the balanced input/outputs. Use either mono plugs, or ensure that ring and sleeve are bridged inside the stereo plug (or pins 1 & 3 in the case of XLR connectors).
EURORACK UB1222FX-PRO 5. SPECIFICATIONS Mono inputs Microphone inputs (IMP Invisible Mic Preamp) Type XLR, electronically balanced, discrete input circuitry Mic E.I.N. (20 Hz - 20 kHz) @ 0 Ω source resistance -134 dB / 135.7 dB A-weighted -131 dB / 133.5 dB A-weighted @ 50 Ω source resistance @ 150 Ω source resistance -129 dB / 130.5 dB A-weighted Frequency response <10 Hz - 150 kHz (-1 dB), <10 Hz - 200 kHz (-3 dB) Gain range Max.
EURORACK UB1222FX-PRO 6. WARRANTY § 1 WARRANTY CARD/ONLINE REGISTRATION To be protected by the extended warranty, the buyer must complete and return the enclosed warranty card within 14 days of the date of purchase to BEHRINGER Spezielle Studiotechnik GmbH, in accordance with the conditions stipulated in § 3. Failure to return the card in due time (date as per postmark) will void any extended warranty claims.