User Manual EURORACK PRO RX1602 Professional Multi-Purpose 16-Input Ultra-Low Noise Line Mixer
EURORACK PRO RX1602 User Manual Table of Contents Important Safety Instructions....................................... 3 Legal Disclaimer.............................................................. 3 Limited warranty............................................................. 3 1. Introduction................................................................ 4 1.1 Before you get started....................................................... 4 1.1.1 Shipment..............................................
EURORACK PRO RX1602 User Manual Important Safety Instructions Terminals marked with this symbol carry electrical current of sufficient magnitude to constitute risk of electric shock. Use only high-quality professional speaker cables with ¼" TS or twist-locking plugs pre-installed. All other installation or modification should be performed only by qualified personnel.
EURORACK PRO RX1602 User Manual 1. Introduction Congratulations! With the EURORACK PRO RX1602, you have purchased a multifarious “problem-solver” for signal distribution. This piece of equipment was developed for those among you with the highest expectations, who are in the business of professional recording, radio and TV broadcast studios, PA and home recording situations, etc.
EURORACK PRO RX1602 User Manual (2) By using the BALANCE control, you can • set up the position of mono signals in the stereo image, and • regulate the ratio of left/right channel signals when processing stereo signals (3) The MUTE switch is used to interrupt the signal path, thus muting the respective channel. When pressed (signal muted) the switch is lit red.
EURORACK PRO RX1602 User Manual 3. Applications 3.1 Keyboards sub-mixer Very often, keyborards feature a stereo design, their signals are already pre-amplified and require no sound processing. To avoid using valuable channels of your main mixer for a purpose other than processing mic signals, you can instead use your RX1602 as a sub-mixer. (13) In this case, the output signals of keyboards, samplers or similar sound sources are connected to the inputs (6) of the RX1602.
EURORACK PRO RX1602 User Manual 3.2 Sub-mix with samplers 3.3 Monitoring multi-track recorders Those of you who work with hardware samplers in studio environments, and who combine many outputs of these units on a single RX1602, can save yourselves a lot of frequent plugging in and out of cables. At the same time, you get a practical way to adjust the signal level to various recording equipment inputs. Last but not least, you also get an extra effects bus.
EURORACK PRO RX1602 User Manual 3.4 Small live setup 4. Installation Compact and powerful, feature-rich equipment is optimal for musicians who spend a lot of their time on the road. Fig. 3.4 shows an example of a compact solution for keyboard and vocal amplification, whereby a singing guitar player or an additional musician can easily be integrated into the mix. 4.1 Rack mounting The BEHRINGER EURORACK PRO RX1602 requires one height unit (1 HU) for being installed into a 19" rack.
EURORACK PRO RX1602 User Manual Balanced ¼" TRS connector strain relief clamp sleeve ring tip sleeve ground/shield ring cold (-ve) tip hot (+ve) For connection of balanced and unbalanced plugs, ring and sleeve have to be bridged at the stereo plug. 5. AUX Channels Modification All monitor and effects signals are tapped into post mute and pre fader, which resembles the function of a pre fader aux channel on conventional mixing consoles.
EURORACK PRO RX1602 User Manual 6. Specifications Audio Inputs Power Supply Input L/R Voltage Type 1/4" TRS connector, electronically balanced Impedance approx. 20 kΩ balanced, 10 kΩ unbalanced Gain range -∞ to +15 dB Operating level variable, +4 dBu/-10 dBV (switchable) Max. input level +22 dBu Common-mode rejection CMRR @ 1 kHz typ. 44 dB USA/Canada 120 V~, 60 Hz Europe/U.K.
We Hear You
