Use and Care Manual

BEHR
®
FAST DRYING
OIL-BASED POLYURETHANE
©2019 Behr Process Corporation
Santa Ana, CA 92705 U.S.A. • behr.com
REV. 8/18
• Durable Clear Protective Finish
• Recoat in 2 Hours
• Resists Stains and Scratches
• Protects & Beauties Interior Wood
• Dries to Touch in 2 Hours
Clean-Up:
Mineral Spirits
Prep Before Use
3 Coats Required
Spread Rate:
15-20 Sq. Ft.
No. B7110 Series
Available in
Satin, Semi-Gloss,
Gloss, and Matte
WARNING Cancer and Reproductive Harm
www.P65Warnings.ca.gov
WHERE TO USE
• Properly prepared interior unfinished and finished wood surfaces such as
furniture, moldings, cabinets, trim and doors.
SURFACE PREPARATION
†
(The following steps are recommended for best results)
• For renishing, remove all wax or cleaner build-up with wax stripper or degreaser,
prior to sanding.
• Sand all surfaces in the direction of the wood grain to desired smoothness.
• Do not use steel wool.
• Remove all dust from sanded surfaces and clean with tack cloth.
• If desired, apply BEHR
®
Wood Stain. Follow all label instructions.
APPLICATION
• Do not apply in direct sunlight or in temperatures below 55°F (10°C) and above
90°F (32°C).
• Shake can vigorously for 1 minute after mixing ball begins to rattle and often
during use.
• Protect adjacent areas from overspray. Wet overspray can be removed with
mineral spirits.
• Hold can vertically 12 inches from surface. Depress button fully and spray using an
even, sweeping motion with slightly overlapping strokes. On unnished wood, apply
sufcient material to seal open joints, edges and end-grain.
• Apply thin coats to avoid runs and sags. Recoat within 2-4 hours. If unable to do
so, wait a minimum of 72 hours, then lightly sand and recoat.
• Apply at least 3 coats on unnished wood and 2 coats on surfaces already nished.
• After nal coat, allow at least 24 hours before normal use.
Note: Above dry times are based on good ventilation, temperature of 77°F and
50% relative humidity. Lower temperature, higher humidity, lack of air movement or
application of thick coats will extend drying times.
Slight ambering may be experienced when Polyurethane is applied over light-colored
wood surfaces. Always spot test on an inconspicuous area to ensure satisfactory
results.
NOZZLE CARE
• After each use, clear valve by holding can upside down and spraying until only
clear gas comes out.
• If spray button becomes clogged, wear eye protection, wipe off button opening
with lacquer thinner. Do not stick pin in spray button opening.
LIMITED WARRANTY
• Visit behr.com/warranty or call 1-800-854-0133 Ext. 2
for more information.
†
WARNING If you scrape, sand or remove old paint, you may
release lead dust. LEAD IS TOXIC. Contact the National Lead
Information Center at 1-800-424-LEAD or visit www.epa.gov/lead.
IMPORTANT! STORAGE AND DISPOSAL: DANGER!IMPORTANT! STORAGE AND DISPOSAL: DANGER! Rags, steel wool and waste soaked with BEHR FAST
DRYING POLYURETHANE may spontaneously catch re if improperly discarded or stored. To avoid a spontaneous
combustion re, immediately after use, place rags, steel wool or waste in a sealed water-lled, metal container. Do
not store unused product inside the home. For disposal guidance, contact your household refuse collection service,
re department, county or state government control agency.
PLEASE SEE PRODUCT LABEL FOR SPECIFIC
WARNINGS. WARNINGS MAY VARY BETWEEN
PRODUCTS AND OR COLORS.
VENTILATION REQUIRED: To avoid inhalation and combustion hazards (see below), DO NOT use this
product unless you can achieve cross ventilation by opening windows and doors during application and drying.
CONTAINS ACETONE, PROPANE, NAPTHA, BUTANE AND PETROLEUM DISTILATES. HARMFUL OR
FATAL IF SWALLOWED. VAPOR HARMFUL. May affect the brain or nervous system causing dizziness, headache or
nausea. CAUSES SERIOUS EYE IRRITATION. IRRITATES SKIN, NOSE AND THROAT. Do not breathe vapors
or spray mist. If you experience eye watering, headaches or dizziness, increase fresh air, wear respiratory protection (NIOSH/MSHA TC
23C or equivalent) or leave the area. NOTICE: Reports have associated repeated and prolonged occupational overexposure to solvents
with permanent brain and nervous system damage. VAPORS MAY IGNITE EXPLOSIVELY. Do not spray near sparks, heat
or open flame. Do not smoke. Vapors are heavier than air and can travel at floor level to distant ignition sources. Extinguish all flames
and pilot lights and turn off stoves, heaters, electric motors, high intensity lights and other sources of ignition during use and until all
vapors are gone. WARNING-CONTENTS UNDER PRESSURE. Do not puncture or incinerate container. Do not expose to
heat or store at elevated temperatures above 120°F. Prolonged exposure to sun may cause bursting. FIRST AID: If you have difficulty
breathing, leave area to obtain fresh air. If difficulty continues, get medical attention immediately. If swallowed, do not induce vomiting.
Call physician immediately. In case of eye contact, flush immediately with plenty of water for at least 20 minutes and get medical attention.
For skin contact, wash thoroughly with soap and water.
CAUTION: KEEP OUT OF REACH OF CHILDREN. DO NOT TAKE INTERNALLY.
Max VOC: 67% by Weight - Max Product Weighted MIR: 0.85
DOT 2P M579