TDS
TECHNICAL DATA SHEETTECHNICAL DATA SHEET
INTERIOR CEILING PAINT
NO. 1458 PURE WHITE®
PRODUCT INFORMATION
BEHR MARQUEE® Interior Ceiling Paint is our most advanced interior paint & primer
◊
that delivers exceptional stain-blocking,
spatter resistance and hide. It features one-coat hide guaranteed* in colors from our exclusive MARQUEE Interior One-Coat Color
Collection (colors denoted with a “u”).
RECOMMENDED USES:
Ideal for properly prepared coated and uncoated interior substrates such as:
• Drywall/Gypsum Board • Plaster • Concrete • Masonry • Wood
COMPLIES WITH THE BELOW AS OF 7/1/2020
SCAQMD YES AIM YES
CARB SCM 2007 YES GREENGUARD
®#
YES
OTC Phase II YES LEED® v.4
†
YES
OTC YES CHPS YES
LADCO YES NAHB/ICC NGBS YES
This coating conforms to USDA regulatory requirements
for incidental food-contact materials intended for use on
surfaces not in direct contact with food, such as walls, oors
and ceilings.
#
GREENGUARD® is a registered trademark of UL Company.
†
Please visit www.usgbc.org/LEED for additional details.
PRODUCT SPECIFICATIONS:
Tint Bases/Max Tint Load:
No. 1458 Pure White® 126 oz / 4 oz
Gloss: <3 @ 60°
Sheen: <3 @ 85°
Resin Type: 100% Acrylic
Weight per Gallon: 13.1 lb
% Solids by Volume: 46% ± 2%
% Solids by Weight: 64% ± 2%
VOC: <50 g/L
Flash Point: N/A
Viscosity: 105 – 112 KU
Recommended Film Thickness:
Wet: 4.0 mils / Dry: 1.8 mils @ 400 sq ft/gal
Coverage: Up to 400 sq ft/gal depending on application
method and substrate porosity. Does not include the loss of
material from spraying.
APPLICATION:
Brush: Nylon/polyester
Roller: 3/8" – 1/2" nap roller cover, depending on surface
texture
Airless Spray:
Tip: .015" – .019"
Filter: 60 mesh
Fluid Pressure: 1,400 – 2,400 psi
Thinning: Do not thin if using a roller or brush; however, if
using a sprayer and thinning is required, thin with water at a
rate of no more than 1/2 pint per gallon.
Dry Time: @ 77°F & 50% RH
To Touch: 1 hour
To Recoat: 2 hours
Full Cure: 4 weeks
Dry times are temperature, humidity, and lm thickness
dependent.
SURFACE PREPARATION:
All surfaces must be clean, free of dust, chalk, oil, grease,
wax, polish, mold and mildew stains, loose and peeling
paint, rust and all other foreign substances.
Drywall: All drywall surfaces should be suciently sanded
smooth. Remove any remaining drywall dust prior to
priming. Allow all drywall compounds to be completely dry
prior to coating.
Wood: Remove mill glaze with sandpaper to open the pores
of the wood. For severe stains caused by mold, mildew,
algae and fungus, apply a mildew stain removing product.
Set nails and ll holes, scratches, and gouges with the
appropriate wood ller and let dry completely. Remove all
dust with a wiping cloth. Fill all gaps with a 100% acrylic,
siliconized, paintable caulking and allow to dry completely.
Patched and lled surfaces should be sanded smooth and
dusted clean prior to coating.
Masonry: Allow to cure for 30 days. The pH must be 10 or
lower prior to coating. Remove bond breakers and all form
release and curing agents. Smooth masonry may require an
adequate prole for adhesion. Remove all loose aggregate
and debris. If painting cannot wait 30 days or pH level is
above 10, allow the surface to cure 7 days and prime the
surface with an alkali-resistant primer.
Plaster: New plaster should be thoroughly dried out and
cured for a minimum of 30 days before painting. When
cured, clean using a mixed solution of one part vinegar
and one part water to remove eorescence and neutralize.
Prime the area with an alkali-resistant primer.
Stain-Blocking: After priming, test for stain bleed-through
by applying the topcoat to a small section. If the stain bleeds
through the topcoat, apply a second coat of primer and
test again before topcoating the entire area. If bleeding
continues, primer may need a longer dry time before
applying topcoat.
Previously Painted Surfaces: Remove all loose and
peeling paint and all other foreign substances. Clean any
dirt and grease by scrubbing the surface with a detergent
and water solution, followed by a thorough rinsing with
clean water. Set nails and ll holes, scratches, and gouges
with the appropriate wood ller and let dry completely.
Remove all dust with a tack or wiping cloth. Fill all gaps with
a 100% acrylic, siliconized, paintable caulking, and allow to
completely dry prior to coating.
Glossy Surfaces: For maximum adhesion, sand the surface
thoroughly to provide a rough surface before coating.
WARNING! If you scrape, sand or remove old paint, you
may release lead dust. LEAD IS TOXIC. EXPOSURE TO LEAD
DUST CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE,
ESPECIALLY IN CHILDREN. PREGNANT WOMEN SHOULD
ALSO AVOID EXPOSURE. Wear a NIOSH-approved respirator
to control lead exposure. Clean up carefully with a HEPA
vacuum and a wet mop. Before you start, nd out how to
protect yourself and your family by contacting the National
Lead Information Center at 1-800-424-LEAD or log on to
www.epa.gov/lead.
SYSTEM RECOMMENDATIONS:
Although BEHR MARQUEE® Interior Paint is a paint & primer
◊
(self-priming - rst coat is the primer and the second coat
is the nish) over most properly prepared surfaces, it is
recommended for optimum performance to follow the
primer recommendations provided below:
Drywall/Gypsum Wallboard:
• Self-prime using 2 coats of BEHR MARQUEE® Interior Paint
or
• 1 coat BEHR® Kitchen, Bath & Trim Interior Stain-Blocking
Primer & Sealer No. 75
2 coats BEHR MARQUEE® Interior Paint
Masonry:
• Self-prime using 2 coats of BEHR MARQUEE® Interior Paint
or
• 1 coat BEHR® Kitchen, Bath & Trim Interior Stain-Blocking
Primer & Sealer No. 75
2 coats BEHR MARQUEE® Interior Paint
This information is provided “as is” and no representations or warranties, either express or implied, of merchantability, tness for a particular purpose or of any other nature
are made with respect to this information or to any product referred to in this information. For SDS or to consult with a Behr Paint Company representative, call 1-800-854-
0133 Ext. 2 (U.S.A. only) or visit behr.com. ©2020 Behr Process Corporation, Santa Ana, CA 92705 U.S.A.
◊
A primer coat may be needed on some surfaces. See SYSTEM RECOMMENDATIONS for details.
*For details visit behr.com/marqueeguarantee.
Revised 7/2020
1 of 2