Specification
TECHNICAL DATA SHEET
This information is provided “as is” and no representations or warranties, either expressed or implied, of merchantability, tness for a particular purpose or of any other
nature are made with respect to this information or to any product referred to in this information. For MSDS or to consult with a Behr Certied Coatings Professional,
call 1-800-854-0133 Ext. 2 (U.S.A. only). ©2017 Behr Process Corporation Santa Ana, CA 92704 U.S.A.
Revised 6/2017
1 of 2
CEILING PAINT
NO. 1458 PURE WHITE
PRODUCT INFORMATION
BEHR MARQUEE® Ceiling Paint oers one-coat-hide guarantee and stain resistance plus an Exclusive MARQUEE Interior
One-Coat Color Collection (colors denoted with a “u.”)
RECOMMENDED USES:
On properly prepared coated and uncoated interior ceilings:
• Drywall/Gypsum Board • Plasterboard • Cured plaster
PRODUCT SPECIFICATIONS:
Tint Bases/Max Tint Load:
Pure White No. 1458 126 oz / 4 oz
Gloss: <3 @ 60°
Sheen: <3 @ 85°
Resin Type: 100% Acrylic
Weight per Gallon: 13.0 lbs.
% Solids by Volume: 46 ± 2%
% Solids by Weight: 63 ± 2%
VOC: <50 g/L
Flash Point: N/A
Viscosity: 105-120 KU
Recommended Film Thickness:
Wet: 4.0 Dry: 1.8 mils @ 400 sq ft/gal
Coverage: Up to 400 sq ft/gal depending on application
method and substrate porosity. Does not include the loss of
material from spraying.
APPLICATION:
Brush: Nylon/polyester
Roller: 3/8" - 1/2" nap
Airless Spray: At packaged consistency
Tip: .015"- .019"
Filter: 60 mesh
Thinning: (If required) No more than 1/2 pint
of water per gallon.
Dry Time: @ 77° & 50% RH
Longer dry time may be required in cooler temperatures
and higher humidity.
To Touch: 1 hour
To Recoat: 2 hours
Full Cure: 4 weeks
SURFACE PREPARATION:
All surfaces must be clean, free of dust, chalk, oil, grease, wax,
polish, mold and mildew stains, loose and peeling paint, rust
and all other foreign substances.
New Drywall: All drywall surfaces should be suciently
sanded smooth. Remove any remaining drywall dust
prior to priming. Allow all drywall compounds to be completely
dry prior to coating. Previously Painted Drywall: Remove
all loose and peeling paint and all
other foreign substances. Clean any dirt and grease by
scrubbing the surface with a detergent and water solution,
followed by a thorough rinsing with clean water. Set nails and
ll holes, scratches, and gouges with the appropriate spackling
material. Let dry completely and sand smooth.
Remove all dust with a wiping cloth. Fill all gaps with a 100%
acrylic, siliconized, paintable caulking, and allow
to completely dry prior to coating. Glossy Surfaces:
For maximum adhesion, sand the surface thoroughly
before coating.
New Plaster: New plaster should be thoroughly dried
out and cured for a minimum of 30 days before painting. When
cured, clean using a mixed solution of one part vinegar and one
part water to remove eorescence and neutralize. Previously
Painted Plaster: Remove all loose and peeling paint and
all other foreign substances. Clean any dirt and grease by
scrubbing the surface with a detergent and water solution,
followed by a thorough rinsing with clean water. Set nails and
ll holes, scratches, and gouges with the appropriate spackling
material and let dry completely and sand smooth. Remove
all dust with a tack or wiping cloth. Fill all gaps with a 100%
acrylic, siliconized, paintable caulking, and allow to completely
dry prior to coating. Glossy Surfaces: For maximum adhesion,
sand the surface thoroughly before coating.
Stain-Blocking: After priming, test for stain
bleed-through by applying the topcoat to a
small section. If the stain bleeds through the topcoat,
apply a second coat of primer and test again before
top-coating the entire area. If bleeding continues,
a longer dry time may be needed before top-coating.
WARNING! If you scrape, sand or remove old paint,
you may release lead dust. LEAD IS TOXIC. Contact the
National Lead Information Center at 1-800-424-LEAD or
visit www.epa.gov/lead.
RECOMMENDED PRIMER/SYSTEMS:
PROPERLY PREPARED NEW SURFACES:
Drywall, Plaster, Masonry and Wood:
• 2 coats is the minimum required for new or uncoated
surfaces and surfaces with severe tannin and stains.
PREVIOUSLY PAINTED SURFACES:
• Use a full coat, or spot prime repaired surfaces with heavy
stains, including tannin, with BEHR MARQUEE®
Interior Paint.
CLEAN UP:
Clean all tools and equipment with clean water.
For disposal of empty containers and unused product,
contact your household refuse collection service.
CAUTIONS/LIMITATIONS:
• Protect from freezing.
• Do not use on oors.
• For best results, apply at temperatures between
50°F - 90°F. Temperatures above 90°F may aect the
application such as drying too fast. Avoid painting in
direct sun. NOTE: If the surface is hot to the touch it
should be considered too hot to apply this coating.
• Avoid heavy trac for 24 hours.
• Allow four weeks before washing or cleaning for full cure.
• Shelf life under normal conditions is two years unopened.
COMPLIES WITH THE BELOW AS OF 6/1/2017
SCAQMD YES LADCO YES
CARB YES AIM YES
OTC YES LEED v.3 (2009)
†
YES
This coating conforms to USDA regulatory requirements
for incidental food-contact materials intended for use
on surfaces not in direct contact with food, such as walls,
oors and ceilings.
†
Please visit www.usgbc.org/LEED for additional details.