TDS
TECHNICAL DATA SHEETTECHNICAL DATA SHEET
This information is provided “as is” and no representations or warranties, either express or implied, of merchantability, tness for a particular purpose or of any other
nature are made with respect to this information or to any product referred to in this information. For SDS or to consult with a Behr Paint Company representative, call
1-800-854-0133 Ext. 2 (U.S.A. only) or visit behr.com. ©2020 Behr Process Corporation, Santa Ana, CA 92705 U.S.A.
Revised 2/2020
1 of 2
PRODUCT INFORMATION
BEHR® DECKPLUS® SEMI-TRANSPARENT WATERPROOFING WOOD STAIN is a 100% acrylic formula which lasts for up to 3
years on decks and 5 years on fences and siding, due to its durability. Choose from 60 dierent colors that add beauty
while allowing the natural wood grain to show through. The stain provides a durable, water-repellent nish that also
protects against the sun’s harmful UV rays. Clean-up is easy with soap and water.
RECOMMENDED USES:
Ideal for use on properly prepared exterior vertical and horizontal substrates such as:
• Wood • Engineered (Synthetic) Wood • Pressured Treated Lumber
PRODUCT SPECIFICATIONS:
Tint Bases/Max Tint Load:
No. 3077 Tint Base 128 oz / 10 oz
Resin Type: 100% Acrylic
Weight per Gallon: 8.6 lb
% Solids by Volume: 17% ± 2%
% Solids by Weight: 20% ± 2%
VOC: <100 g/L
Flash Point: N/A
Viscosity: 20-45 sec #2 Zahn Cup
Recommended Film Thickness:
Wet: 6.4 mils / Dry: 1.1 mils @ 250 sq ft/gal
Wet: 3.2 mils / Dry: 0.5 mils @ 500 sq ft/gal
Coverage: 250-300 sq ft/gal depending on application
method and substrate porosity. Apply a thinner second coat
at a spread rate of approximately 500-600 sq ft/gal. 2 coats
are required for optimal appearance and durability.
APPLICATION:
Pad Applicator (recommended over large deck areas)
Brush: Nylon/polyester brush
Roller: 3/8" nap roller cover (limited to rough surfaces only)
Airless Spray:
Tip: .015"- .019"
Filter: 60 mesh
Fluid Pressure: 1,400 – 2,400 psi
Follow spraying immediately with a pad, back brushing
or back rolling for a uniform appearance.
Thinning: DO NOT THIN PRODUCT
Dry Time: @ 77°F & 50% RH
To Recoat: 1-2 hours
Light Foot Trac: 24-48 hours
Full Cure: 72 hours
Dry times are temperature, humidity, and lm
thickness dependent.
SURFACE PREPARATION:
The following steps and products are recommended
for best results: : If you use a product such as BEHR
PREMIUM® Wood Stain & Finish Stripper No. 64 to remove
loose wood bers, latex, oil-based and 100% acrylic
coatings on new weathered wood, then you must use a
product such as BEHR PREMIUM® All-In-One Wood Cleaner
No. 63 to clean, brighten & neutralize wood. If you do not
use a product such as BEHR PREMIUM Wood Stain & Finish
Stripper No. 64, then use a product such as BEHR PREMIUM
All-In-One Wood Cleaner No. 63 to clean and brighten the
wood surface and to remove light to medium stains caused
by mold, mildew, algae & fungus. Rinse thoroughly and
allow to dry before coating. On new wood, use a product
such as BEHR PREMIUM All-In-One Wood Cleaner No. 63 to
remove mill glaze and open the pores of the wood. Lightly
sand to remove remaining wood bers/fuzz.
WARNING! If you scrape, sand or remove old paint, you
may release lead dust. LEAD IS TOXIC. EXPOSURE TO LEAD
DUST CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE,
ESPECIALLY IN CHILDREN. PREGNANT WOMEN SHOULD
ALSO AVOID EXPOSURE. Wear a NIOSH-approved respirator
to control lead exposure. Clean up carefully with a HEPA
vacuum and a wet mop. Before you start, nd out how to
protect yourself and your family by contacting the National
Lead Information Center at 1-800-424-LEAD or log on to
www.epa.gov/lead.
CLEAN-UP/DISPOSAL:
Clean all tools and equipment with warm, soapy water. Do
not dispose of this product down a drain. If spilled, contain
material and remove with an inert absorbent. Dispose of
contaminated absorbent, container and unused product
in accordance with all current federal, state and local
regulations. For recycling or disposal of empty containers,
unused product and soiled rags, contact your household
refuse collection service.
CAUTIONS/LIMITATIONS:
• Protect from freezing.
• For best results, apply when air, material and surface
temperatures are between 40°F and 90°F. Avoid applying
stain in direct sunlight or to hot surfaces. Temperatures
above 90°F can cause the paint to dry too fast. Do not
apply if rain is expected within 24 hours of product
application.
• Test product for color on a small hidden area before
proceeding.
• Avoid applying stain too heavily. Over-application of
DECKPLUS SEMI-TRANSPARENT WATERPROOFING WOOD
STAIN results in lm forming on the wood surface and
therefore subject to peeling and aking.
• Stained surfaces may become slippery when wet.
• Shelf life under normal conditions is 2 years unopened.
GENERAL INFORMATION:
WARNING IRRITANT HARMFUL IF SWALLOWED.
CONTAINS: ETHYLENE GLYCOL.MAY CAUSE EYE, NOSE AND
THROAT IRRITATION. AVOID CONTACT WITH SKIN AND EYES
AND AVOID BREATHING OF VAPORS AND SPRAY MIST. WEAR
EYE PROTECTION AND PROTECTIVE CLOTHING. USE ONLY WITH
ADEQUATE VENTILATION. To avoid breathing vapors and
spray mist, open windows and doors or use other means to
ensure fresh air entry during application and drying. If you
experience eye watering, headaches or dizziness, increase
fresh air. If properly used, a respirator (NIOSH approved for
organic vapor with P series particulate pre-lter) may oer
additional protection; obtain professional advice before
using. A dust mask does not provide protection against
vapors. Avoid contact with eyes and skin. Wash thoroughly
after handling. Close container after each use.
DECKPLUS® SEMI-TRANSPARENT WATERPROOFING WOOD STAIN
NO. 3077 TINT BASE
COMPLIES WITH THE BELOW AS OF 2/1/2020
SCAQMD YES OTC YES
CARB SCM 2007 YES LADCO YES
CARB YES AIM YES
OTC Phase II YES