User Manual

ManualsBrandsBehavior Tech Computer ManualsComputers & AccessoriesWireless Keyboard

5189URF Quick Installation Guide

Important Information

- For Windows® 98SE operating system, please go to http://www.btc.com.tw/ website to download and install the

“KeyMaestro Input Device Driver” to have the Internet Keys Block and Multimedia Keys Block functions.

- For Windows® ME, Windows® 2000 and Windows® XP operating system, you can use the keyboard

immediately after plugging the receiver connector into PC. If you want to enjoy the full potentiality function of the

keyboard, please visit our website at http://www.btc.com.tw/ to download and install the “KeyMaestro Input

Device Driver”. Once the driver has been installed, these hot keys are reprogrammable, except Volume Up /

down and Mute. They can be configured as a string, a combination key, a web site, an existing file, or a function

that the driver pre-defines for you.

Hardware Installation

1. Plug in the dongle receiver connector into your available USB port on PC.

2. Make sure the batteries of the keyboard and mouse are installed correctly. Please follow the polarity signs in the

battery compartment.

3. Please make sure the power switch on the back of the mouse is switched to “on” before using the mouse. When

not in use, please turn the power switch to “off” for power saving.

ID Pairing Procedure

After you plug the receiver USB connector into your PC USB port, please hold the keyboard and mouse

close to the receiver within 1M and press any keys to pair ID. If it can’t work, please follow the steps below to

process the ID pairing procedures of the Wireless Kit.

The ID-recognition function helps to protect against interference from other RF products in the same environment.

Remember to follow the steps below to change ID when other RF products affect your keyboard kit.

w ID pairing/connect button location:

- Receiver ID pairing/connect button→ on the top of the dongle receiver

- Mouse ID pairing/connect button→ on the bottom of the mouse

- Keyboard ID pairing/connect button→ on the bottom of the keyboard

w ID pairing procedures:

1. Press and hold the ID pairing/connect button on the top of the dongle receiver at least 5 seconds until the

receiver LED flashes 3 times. The receiver LED will flash 60 seconds to wait for keyboard and mouse pairing

information. (If you release the button within 5 seconds, the ID doesn’t make any changes.)

2. Hold the keyboard and mouse close to the dongle receiver within 1M.

3. Press and hold the keyboard ID pairing/connect button on the bottom of the keyboard at least 5 seconds until

the keyboard LED, which is on the right upper of the keyboard, flashes once. (If you release the button within 5

seconds, the ID pairing will fail.)

4. Press and hold the mouse ID pairing/connect button on the bottom of the mouse at least 5 seconds until the

mouse LED off. (If you release the button within 5 seconds, the ID pairing will fail.)

5. The receiver LED indicator flashes 3 times rapidly as indication its’ ID paired with this keyboard and mouse. Then

you could press any keys to check if the keyboard and mouse work or not.

Note:

- Make sure your PC is on and running when doing the pairing procedure.

- You don’t have to pair ID again after changing batteries. If it can’t work, please follow the steps above to pair ID.

Driver Installation

n USB Device Driver

The USB device driver is included with your Windows operating system.

During the initial installation of the keyboard USB device, the system will automatically detect that a new hardware

device has been added and will bring up the "Add New Hardware Wizard" dialogue box. Follow the Wizard's USB

driver installation steps. Once this installation step is completed, the basic functions of the USB device will work

under the operating system. The additional functions are provided only after the KeyMaestro driver is installed.

n KeyMaestro Input Device Driver

1. After you download the driver, please find the “SetupKey.exe” in the directory and double-click this file.

2. Follow the on-screen instructions to install the driver.

3. The driver icon will show at the right-bottom of the Windows system tray when the driver is loaded.

Summary of content (3 pages)

PAGE 1
5189URF Quick Installation Guide Important Information - For Windows® 98SE operating system, please go to http://www.btc.com.tw/ website to download and install the “KeyMaestro Input Device Driver” to have the Internet Keys Block and Multimedia Keys Block functions. - For Windows® ME, Windows® 2000 and Windows® XP operating system, you can use the keyboard immediately after plugging the receiver connector into PC.
PAGE 2
Important Usage Information w Battery: 1. We recommend using alkaline batteries for a longer battery life. 2. Always change batteries when battery low alarm appears, otherwise the mouse or keyboard will shut down once the battery voltage is too low. 3. Don't mix different types of batteries or new and old batteries together. Always replace old batteries with new and same type batteries. 4. Remove batteries after long periods of non-use.
PAGE 3
FCC GUIDELINES This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions may cause harmful interference to radio communications.