AP-02FC Blutooth LE Module Specification Ver0.4 Product Specification Bluetooth LE 5 Module Model Name: AP-02FC VERSION: 0.4 20F-B, No.98, Sec. 1, Xintai 5th Rd.
AP-02FP Blutooth LE Module Specification Ver0.4 TABLE OF CONTENTS 1. INTRODUCTIONS AND SCOPE 1 2. FEATURES 2 3. MECHANICAL CHARACTERISTICS 3 4. EXTERNAL DIMENSION 4 5. PIN ASSIGNMENT AND DESCRIPTION 5 6. ELECTRICAL CHARACTERISTICS 7 6.1 ABSOLUTE MAXIMUM RATINGS 6.2 RECOMMENDED OPERATING CONDITIONS 6.3 ELECTRICAL PERFORMANCE SPECIFICATION 7.
AP-02FP Blutooth LE Module Specification Ver0.4 1. INTRODUCTIONS AND SCOPE AP-02FP is a Bluetooth low energy (BLE) module. It uses ON Semiconductor BLE controller RSL10, which is an ultra−low−power, highly flexible multi−protocol 2.4 GHz radio chipset. AP-02FP is designed for high−performance wearable, medical, and industrial applications. The module integrates PCB antenna, crystal, and controller relative circuit, customer can easily apply it in product.
AP-02FP Blutooth LE Module Specification Ver0.4 2. FEATURES Bluetooth 5 Certified with LE 2M PHY Support Designed with PCB antenna Build in 48MHz system clock crystal Rx Sensitivity (Bluetooth Low Energy Mode, 1 Mbps): −94 dBm Transmitting Power: −17 to +6 dBm Build in Arm Cortex−M3 Processor Build in LPDSP32 for Audio Codec Support lower voltage to 1.
AP-02FP Blutooth LE Module Specification Ver0.4 3. MECHANICAL CHARACTERISTICS 3.1 Weight and Dimension Weight: 0.8g (L x W x H, without metal cover) 1.0g (L x W x H, with metal cover) Dimension: 20mm x 14mm x 2mm (L x W x H, without metal cover) 20mm x 14mm x 2.7mm (L x W x H, with metal cover) 3.
AP-02FP Blutooth LE Module Specification Ver0.4 4. EXTERNAL DIMENSION 4.
AP-02FP Blutooth LE Module Specification Ver0.4 5. PIN ASSIGNMENT AND DESCRIPTION 5.1 Pin Assignment Top Side View 5.
AP-02FP Blutooth LE Module Specification Ver0.4 21 GND P Ground Legend: Type: A = analog; D = digital; I = input; O = output; P = power Pull: U = pull up; D = pull down Pull up: selectable between 10 k_ and 250 k_. U1 = pull up, 200 k_. Pull down: 250 k_ All digital pads have a Schmitt trigger input. All DIO pads have a programmable I2C low pass filter. All DIOs can be configured to no pull.
AP-02FP Blutooth LE Module Specification Ver0.4 6. ELECTRICAL CHARACTERISTICS 6.1 Absolute Maximum Ratings Symbol Par VBAT Power supply voltage VDDO I/O supply voltage T functional T storage Min Max Unit 3.63 V 3.63 V Functional temperature range −40 85 °C Storage temperature range −40 85 °C 6.2 Recommended Operating Conditions Description Supply voltage operating range Symbol VBAT Condition Input supply voltage on VBAT pin (Note 1) Min 1.25 Typ 1.25 Max Units 3.
AP-02FP Blutooth LE Module Specification Ver0.4 Deep sleep current, example 3, VBAT = 1.25 V Ids3 As Ids2 but with 8 kB RAM data reten- tion. − 300 − nA Standby Mode current, VBAT = 1.25 V Istb Digital blocks and memories are not clocked and are powered at a reduced voltage. − 30 − μA Current consumption RX, VBAT = 3 V IVBAT RX Mode, ON Semiconductor propri- etary audio streaming protocol at 7 kHz audio BW, 5.5 ms delay. − 0.
AP-02FP Blutooth LE Module Specification Ver0.4 RADIO FRONT−END: General Specifications FRF Frequency range Supported carrier frequencies 2360 − 2500 MHz Current consumption at 1 Mbps, VBAT = 1.25 V IBATRFRX VDDRF = 1.1 V, 100% duty cycle − 5.6 − mA Current consumption at 2 Mbps, VBAT = 1.25 V IBATRFRX VDDRF = 1.1 V, 100% duty cycle − 6.2 − mA Current consumption at 1 Mbps, VBAT = 3 V, DC−DC IBATRFRX VDDRF = 1.1 V, 100% duty cycle − 3.
AP-02FP Blutooth LE Module Specification Ver0.4 7. RF Warnings FCC Statement: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
