User's Manual

ManualsBrandsBeautiful ManualsElectronicsBluetooth Module

BC05 ROM Module Spec.

Shenzhen Synchron Electronics Co., Ltd. 2012.08

1. General Description and Specification

1.1 General Description

This product is a Class 2 SMT Bluetooth Module used CSR BC5-BlueTunes ROM. It

provides data and voice communications. Support data rate up to 3Mbps.

General Features:

■ Class 2 Bluetooth Module

■ Bluetooth Spec. V2.1+EDR Compliant

■ Support Firmware Upgrade

■ High-quality audio 95dB SNR on DAC playback

■ Integrated linear regulator with 1.5V output from 1.8V to 2.7V input

■ Integrated Switched-mode Regulator

■ Integrated 150mA lithium Battery Charger

■ Integrated Microphone bias& LED Driver

■ 64MIPS Kalimba DSP Co-processor

■ cVc support for echo and noise reduction

■ Green (RoHS Compliant)

1.2 Device Details

Radio

 Common TX/RX terminal simplifies external matching; eliminates external antenna switch

 BIST minimises production test time

 Bluetooth v2.1 + EDR specification compliant

Transmitter

 4dBm RF transmit power with level control from onchip 6-bit DAC over a dynamic range

>30dB

 Class 2 and Class 3 support without the need for an external power amplifier or TX/RX

switch

Receiver

 Receiver sensitivity of -70dBm

 Integrated channel filters

 Digital demodulator for improved sensitivity and cochannel rejection

 Real-time digitised RSSI available on HCI interface

Summary of content (13 pages)

PAGE 1
BC05 ROM Module Spec. Shenzhen Synchron Electronics Co., Ltd. 2012.08 1. General Description and Specification 1.1 General Description This product is a Class 2 SMT Bluetooth Module used CSR BC5-BlueTunes ROM. It provides data and voice communications. Support data rate up to 3Mbps. General Features: ■ Class 2 Bluetooth Module ■ Bluetooth Spec. V2.1+EDR Compliant ■ Support Firmware Upgrade ■ High-quality audio 95dB SNR on DAC playback ■ Integrated linear regulator with 1.5V output from 1.8V to 2.
PAGE 2
 Fast AGC for enhanced dynamic range Baseband and Software  Internal ROM  48KB of internal RAM, allows full-speed data transfer, mixed voice/data and full piconet support  Logic for FEC, HEC, access code correlation, CRC, demodulation, encryption bit stream generation, whitening and transmit pulse shaping  Transcoders for A-law, μ-law and linear voice from host and A-law, μ-law and CVSD voice over air  FastStream, CSR low latency codec significantly, reduces the latency of the audio link, f
PAGE 3
 Integrated amplifiers for driving 16Ω speakers; no need for external components  Support for single-ended speaker termination and line output  Integrated low-noise microphone bias Auxiliary Features  Power management includes digital shutdown and wake-up commands with an integrated low-power oscillator for ultra-low power Park/Sniff/Hold mode  On-chip regulators: 1.5V output from 1.8V to 2.7V input  On-chip high-efficiency switched-mode regulator; 1.8V output from 2.7V to 4.
PAGE 4
2. Package Information 2.
PAGE 5
2.
PAGE 6
SPI_MISO 34 SPI data output SPI_CLK 35 SPI clock SPI_MOSI 36 SPI data input VRE_IN 37 Take high to enable high-voltage linear regulator and switch-mode regulator Lithium VDD_BAT 38 ion/polymer battery positive terminal.
PAGE 7
2.3 Package Dimensions Ø0.
PAGE 8
3. Hardware Description 3.
PAGE 9
3.2 RF Ports Figure 4: RF Ports Diagram RF_N and RF_P form a complementary balanced pair and are available for both transmit and receive. On transmit their outputs are combined using an external balun into the single-ended output required for the antenna. Similarly, on receive their input signals are combined internally. Both terminals present similar complex impedances that may require matching networks between them and the balun. An LC network: L9 and C1.
PAGE 10
4. Green Products and RoHS Compliance 5. Reference 1) BlueTunes ROM Product Data Sheet, CS-122312-DSP1 2) Specification of the Bluetooth System, Version 2.
PAGE 11
FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
PAGE 12
no longer considered valid and the FCC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization. End Product Labeling The final end product must be labeled in a visible area with the following: “Contains FCC ID:UZZSFQ04A”.
PAGE 13
Contains transmitter module IC: 7633A-SFQ04A The module must be installed in Sound Kick Audio System. This End equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body. Cet équipement devrait être installé et actionné avec une distance minimum de 20 centimètres entre le radiateur et votre corps. The end user manual shall include all required regulatory information/warning as show in this manual.