User's Manual

ManualsBrandsBCM Communication ManualsElectronicsMobile Router

FEDERAL COMMUNICATIONS COMMISSION

This device complies with Part 15 of the FCC Rules.Operation is subject to the following two

conditions:(1) this device may not cause harmful interference, and (2) this device must

accept any interference received, including interference that may cause undesired

operation.

NOTE

This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equipment generates, uses and can

radiated radio frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation If this equipment does cause

harmful interference to radio or television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct the interference by one or more of

the following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

-Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications not expressly approved by the party responsible for compliance could

void the user‘s authority to operate the equipment.

The antenna(s) used for this transmitter must not be co-located or operating in conjunction with

any other antenna or transmitter

This equipment complies with FCC RF radiation exposure limits ser forth for an uncontrolled environment.

This equipment should be installed and operated with a minimum distance of 20 centimeters between the

radiator and your body.

1 V 0.5

Summary of content (10 pages)

PAGE 1
FEDERAL COMMUNICATIONS COMMISSION This device complies with Part 15 of the FCC Rules.Operation is subject to the following two conditions:(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
PAGE 2
MOR600 Mobile Router Quick Installation Guide 1. Verify Package Contents The MOR600 Mobile Router package should contain the items Listed below . If any of the items are missing please contact your Reseller . • MOR600 Router • Ethernet Cable • DC 5V/2A Power Adapter • User Guide on CD-ROM • Quick Installation Guide 2 V 0.
PAGE 3
2. Connections and LEDS The following figures show the various connectors and status LED indicators on the MOR600 Mobile Router . Power LED PC Card Slot Status LED WiFi Secure Set Button Default Button USB Port (Optional) Ethernet LAN Port Power Jack 3 V 0.
PAGE 4
3. Getting Start Step 1 Plug in power adapter 4 V 0.5 When connect the power adapter to back panel power Jack 。The power LED Will Turn ON to indicate power has been applied.
PAGE 5
STEP 2：Check Status LED When Power ON the MOR600, the status LED Will Flash ON and OFF One by one as MOR600 Performs initialization and Internet connection process。MOR600 Will Auto Configured properly for your Internet Service Account。It Will take a few minutes。 When Complete, the status LED Will illuminate Green。Please refer the below Status LED Activity table for each State。 5 4. V 0.
PAGE 6
STEP 2：Open your browser Such as IE or Netscape and type Press Enter http://192.168.1.1 in address bar. 7 V 0.5 STEP 3：Login Mobile Router • Enter your user name in the Username box. The default user name is admin. • Enter your password in the Password box. The default password is admin. • Click OK.
PAGE 7
STEP 4：Once logged in the following screen is displayed 8 STEP 5：Click WLAN for wireless network setting V 0.
PAGE 8
10 V 0.
PAGE 9
SSID Encryption Key Length Key Type Key1~Key4 ： Enter your SSID name in the field provided. SSID names Can contain up to 32 ASCLL characters. ： You may select from two levels of encryption to secure your wireless Network：None or WEP . ：Two levels of wireless encryption are available：64 bits and 128 bits. ： Two type of WEP Key：Hex or ASCII . choose the proper one for key setting . ： You can enter the WEP key by manually and choose Key1~Key4 for enable. STEP 7：Click LAN for Local Network setting 11 V 0.
PAGE 10
DHCP Server ： This setting is used to configure MOR600’s Dynamic Host Configuration Protocol (DHCP)server function. MOR600 can be used as a DHCP server for the internal LAN network . The DHCP server automatically assigns an IP address to each computer in the LAN network . If you choose to enable MOR600 s DHCP server option, you must configure all of PCs in the LAN network to connect to this DHCP server (MOR600), and make sure there is no other DHCP server on your network .