BDW45.
USER MANUAL FOR YOUR BAUMATIC BDW45.1 45 cm Fully integrated full height electronic dishwasher NOTE: This User Instruction Manual contains important information, including safety & installation points, which will enable you to get the most out of your appliance. Please keep it in a safe place so that it is easily available for future reference; for you or any person not familiar with the operation of the appliance.
Contents Environmental note Important safety information 4 5–7 Specifications Product and aperture dimensions Product specifications Electrical details Description of the appliance Control panel 8 – 11 8 8–9 9 10 11 Using your dishwasher Before first use Filling with dishwasher salt Setting the water softener level Filling with rinse aid Setting the rinse aid level Filling with dishwasher detergent Loading the upper basket Adjusting the upper basket Loading the lower basket The cutlery basket Loading di
ENVIRONMENTAL NOTE Note: Before discarding an old appliance, switch off and disconnect it from the power supply. Cut off and render any plug useless. Cut the cable off directly behind the appliance to prevent misuse. This should be undertaken by a competent person. Disable the door lock to make sure that children cannot get stuck inside the appliance. o The packaging materials that Baumatic uses are environmentally friendly and can be recycled.
IMPORTANT SAFETY INFORMATION Your safety is of the utmost importance to Baumatic. Please make sure that you read this instruction booklet before attempting to install or use the appliance. If you are unsure of any of the information contained in this booklet, please contact the Baumatic Advice Line. General Safety o Repairs to your appliance must only be carried out by a Baumatic engineer or one of its authorised service agents.
o Care should be taken not to trap the power supply cable underneath the appliance whilst installing it. o No attempt should be made to alter or modify the specifications of this appliance. In daily use o This appliance is only designed to wash normal domestic washloads. If you use your dishwasher in any other way or it is incorrectly used, then Baumatic accepts no liability for any damage that might be caused and any guarantee will be void.
Child Safety o Your dishwasher should only be used by adults. You should not allow children in the area of the machine unsupervised. You should not let them touch the controls or play with the appliance. o It could be possible for a child or pet to gain access to the dishwasher if the door is left open. Therefore please check the inside of the appliance before setting it on a wash cycle. o Any packaging that is removed from the machine should be kept away from children.
Specifications Product dimensions Height: Width: Depth: 820 - 850 mm 445 mm 540 mm Aperture dimensions Height: Width: Depth: 820 mm (min) 450 mm 580 mm (min) Product specifications o 8 Place settings o 7 functions: Normal Intensive Economy Rinse Rapid Glass Soak o 5 temperatures: 40°C, 50°C, 55°C, 60°C, 70°C 8
o o o o o o o o o o Delay timer LED display Self-cleaning stainless steel micro-filter Anti-leak device Anti-flood device Height adjustable upper basket Collapsible plate racks Adjustable feet Residual drying Concealed heating element Energy efficiency details Energy efficiency class: A Washing performance class: A Drying performance class: A Power consumption Off mode: Left on mode: 0.00 W 1.
Description of the appliance 1) 2) 3) 4) 5) 6) 7) 8) 9) 10) 11) 12) 10 Upper basket Spray arms Lower basket Water softener Main filter Detergent dispenser Cup shelf Cutlery basket Coarse filter Rinse aid dispenser Drain pipe connector Inlet pipe connector
Control panel 1) 2) 3) 4) 5) 6) 7) Program indicator neons Program selection button Rinse aid and salt indicator neons LED display Delay start button ON/OFF indicator neon ON/OFF button Using your dishwasher Before first use o Install the appliance as per the installation instructions contained within this booklet. o Fill the water softener with 1 litre of tap water and then fill with specialist dishwasher salt. After this you should set the water softener level.
Filling with dishwasher salt IMPORTANT: You should only use salt that is specially designed for use in a dishwasher. If any other type of salt is used in the appliance (in particular table salt), it will damage the water softener. o Ideally you should fill the water softener with salt, just before you are about to run a wash program. This will help to clear any salt that may have overflowed from the water softener during the salt filling process.
o IMPORTANT: You do not need to pour 1 litre of water into the container when you subsequently fill the water softener with salt. Setting the water softener level It is possible to regulate the amount of salt that the water softener will release during a wash cycle. The water softener should be set to a level that is appropriate for the hardness of your water (please refer to the table below).
Filling with rinse aid The rinse aid is released during the final rinse and it helps to prevent water from forming droplets on your dishes. These droplets will lead to spots and streaks being left on items after the wash program has completed. o Your dishwasher is designed to utilise liquid rinse aid. o The rinse aid dispenser is located inside the drop down door, next to the detergent dispenser. o To access the rinse aid dispenser, you should turn the cap anticlockwise and it will pop out of the hole.
o You should continue to adjust the rinse aid level upwards until you get no water spots. o If you get cloudiness or streaking on your dishes, the rinse aid level is set too high and it is causing foaming during the wash cycle. Turn the arrow clockwise and lower the setting to the next number. Filling with dishwasher detergent The detergent dispenser must be refilled at the start of each wash cycle (apart from the Rinse wash program).
Loading the upper basket The upper basket is most suited to washing delicate and light dishware, such as glasses, coffee & tea cups, saucers, plates, bowls and shallow pans (that are not heavily soiled). 1. 2. 3. 4. 5. 6. Cups Small serving bowl Large serving bowl Glasses Saucers Dishes o You should position the dishes and cookware in such a way that they are not moved by the spray of water during the wash cycle. o Use the diagram above as a guide to the most appropriate way to load the upper basket.
o The height of the upper basket can be adjusted by removing the upper basket from the guide supports. o IMPORTANT: The upper basket must be empty when you are removing it from the guide supports. Lower position o If the upper wheels are placed in the guide supports, then the basket is in the lower position. o For accommodating additional tumblers, cups and mugs. You can also place small, espresso sized cups on top of the side racks.
With upper basket raised With upper basket lowered Maximum height of dishes (upper basket) 19 cm Maximum height of dishes (lower basket) 30 cm 24 cm 25 cm IMPORTANT: Care should be taken to make sure that the spray arms can move freely when items have been loaded into the baskets. Loading the lower basket The lower basket is most suited to washing larger and more heavily soiled items, such as saucepans, saucepan lids and serving dishes.
The cutlery basket Cutlery should be placed inside of the cutlery basket. The cutlery basket should then be placed in the appropriate position in the lower basket. 1. 2. 3. 4. 5. 6. 7. 8. Forks Soup spoons Dessert spoons Teaspoons Knives Serving spoon Gravy ladle Serving fork o For the best washing performance, cutlery should be placed through the slots in the top of the cutlery basket.
o Cutlery and dishes should not cover each other; otherwise you may get poor wash results. o Do not allow glasses to touch inside the dishwasher, otherwise damage may occur. o Small objects can be placed inside of the cutlery basket. The following items are NOT suitable for washing inside a dishwasher:o Cutlery with a handle of mother-of-pearl, wood, horn or china. o Plastic items that are not resistant to heat. o Cutlery that consists of glued parts that are not resistant to heat.
o Certain types of glass may become dull or cloudy after a large number of washes. Program table Program Normal ** Intensive Economy Rinse Glass Rapid Soak 21 Cycle Program Description Detergent Program Water Energy of cycle pre/main (l) (kWh) information times* For normally soiled loads, such as pots, plates, glasses and lightly soiled pans, standard daily cycle.
* The wash program times that are quoted are intended as a guide only. Please note that factors external to the machine, e.g. the temperature of your water supply, your water pressure etc. can affect the time it takes for the wash program to complete. ** Normal is the testing program for EN 50242. Setting a wash program Make sure that the before first use section has been followed. o Check whether the appliance needs rinse aid or salt adding to it.
Changing the wash program IMPORTANT: This should only be attempted when the cycle has only just started, otherwise the detergent tablet may have already released or you could have hot water escaping. o Slightly open the door of the appliance and turn off the power using the ON/OFF button. o Wait for a minute before fully opening the door of the appliance. o Turn the appliance on by using the ON/OFF button and wait for 5 seconds before pressing the program selection button.
o Add detergent o Turn the appliance on by using the ON/OFF button. o IMPORTANT: Wait for 5 seconds before pressing the program selection button, otherwise the appliance may not function correctly. o Press the program selection button to choose an appropriate wash program for the load that you are washing. The relevant program indicator neon will light to show which program you have selected.
Saving energy using your dishwasher Loading dishes o Refer to the relevant section of this manual for instructions on placing items in the dishwasher for the most efficient cleaning. o Only run the dishwasher when it is full for optimum energy and water usage. o Check the program table to select the most efficient program according to the size and type of the load. o The ECONOMY program washes your items at a lower temperature and uses less water during the cycle.
Cleaning and maintenance IMPORTANT: The appliance should be disconnected from your mains supply before commencing any cleaning process. The filter system Your appliance is fitted with three levels of filtering; these are located in the base of the dishwasher for ease of access. 1) Main filter 2) Coarse filter 3) Fine filter Main filter- Food and soil particles are trapped by this filter and pulverised by a special jet on the lower spray arm. This debris is then washed down the drain.
Cleaning the filters For best performance and results, the entire filter assembly should be thoroughly cleaned regularly (ideally after each wash cycle). 1. Turn the coarse filter anticlockwise and then lift it upwards. Rinse out this section under a tap to remove any food debris that remains in it. 2. Pull out the main filter and rinse this under the tap to remove any food debris that is trapped in it. 3. Pull out the fine filter and rinse this under the tap to remove any food debris that is trapped in it.
Cleaning the spray arms The spray arms should be cleaned regularly, to prevent hard water deposits from clogging the spray arm jets and bearings. o To remove the upper spray arm, unscrew the nut and take out the washer that sits on top of the spray arm. o Gently pull upwards to remove the lower spray arm. o Wash the spray arm in warm, soapy water and use a soft brush to clean the jets. o Rinse the spray arm thoroughly and then reassemble the spray arm back in its original position.
Cleaning the door o To clean the edge around the outside of the door, you should use a soft, damp cloth only. o To prevent water from penetrating the door lock or electrical components, DO NOT use a spray cleaner of any kind. o DO NOT use any abrasive cleaner or scouring pads on the inner or outer surfaces, as they may cause damage to them. Error code failure system If your appliance senses that it is not operating correctly, then an error code may appear in the display window.
E3 o Longer heating time- not reaching the required temperature. 9 Malfunction of the temperature sensor or heating element. 9 Call the Baumatic Customer Care Department. E4 o The machine has sensed water in the base. 9 Check that the outlet hose is not kinked or crushed. 9 Check that there are no blockages in the drain hose or the drainage system that the appliance is connected to. 9 The drain pipe may be placed in too high a position or incorrectly.
IMPORTANT: If any other fault code appears in the display window, you should not attempt to clear it yourself and contact the Customer Care Department. IF THE FAULT CODE REAPPEARS AFTER FOLLOWING THE ABOVE ADVICE AND CLEARING THE FAULT CODE. YOU SHOULD TURN OFF THE APPLIANCE; DISCONNECT THE APPLIANCE FROM YOUR MAINS SUPPLY. THEN ARRANGE FOR AN ENGINEER TO ATTEND THE APPLIANCE. YOU SHOULD CONTACT THE CUSTOMER CARE DEPARTMENT ON TELEPHONE NUMBER (0118) 933 6911.
Suds in the tub Utensils are not secure in the baskets or something small has dropped into the basket Ensure that everything is loaded as per Baumatic’s loading instructions. Motor hums If the dishwasher is not going to be used for a period of time, then you should make sure that the appliance is set on a wash program once a week. Otherwise the seal around the motor may dry out and cause noise.
Dishwasher leaks The rinse aid dispenser is overfilled or rinse aid has been spilt inside the appliance Take care not to overfill the rinse aid dispenser. Spilt rinse aid could cause oversudsing and lead to overflowing. Wipe away any spills immediately with a damp cloth. Dishwasher isn’t level Make sure that the dishwasher is level. Installation IMPORTANT: THIS INSTALLATION MUST BE COMPLETED BY A SUITABLY QUALIFIED PERSON. BAUMATIC ONLY SANCTION THE INSTALLATION GIVEN IN THIS INSTRUCTION MANUAL.
o The aperture that your dishwasher needs to be installed into should resemble the one shown in the drawing on page 30. o There should be less than a 5 mm gap between the top of the dishwasher and the underneath of the worktop. Installation stages 1. 2. 3. 4. 5. 6. 7. 8. 9. Preparing and connecting the furniture door. Adjusting the tension of the door spring.
o The maximum weight of the furniture door should be 5.5 kilograms. The maximum thickness of the furniture door should be 15 mm. o Use the installation template supplied with the appliance to mark up and then drill out the necessary holes in the furniture door. o Attach the upper hooks onto the furniture door. o Attach the lower hooks onto the furniture door.
Adjusting the tension of the door spring o The door of the dishwasher is attached to springs. These are set at the factory to ensure that they are at the proper tension, so that the door can open and close smoothly. o After the furniture door has been fitted, you will need to adjust the tension of the door spring. o Using an Allen key, rotate the adjusting screw to either tighten or slacken the steel cable.
Connecting to the mains water supply IMPORTANT: Do not connect the appliance to your mains water supply using an old or an existing water inlet hose. The inlet hose supplied with the dishwasher is the ONLY one that should be used. DO NOT CONNECT THE WATER INLET HOSE TO A HOT WATER TAP. o The inlet hose will be located inside the cabinet of the dishwasher. o Connect the water inlet hose (C) to a threaded water tap (A) that has a 3/4” thread and to the inlet hose connector on the appliance.
Connecting to the water outlet o Secure the drain hose, so that it cannot move whilst the dishwasher is in use. o Place the end of the drain hose on your drain pipe. Push it a short way down into your drain pipe. o IMPORTANT: Do not insert the drain hose too deeply into the pipe, as this may cause siphoning. o NEVER EXTEND THE DRAINAGE HOSE FROM ITS ORIGINAL LENGTH.
o IMPORTANT: The electrical socket must still be accessible once the appliance is installed. o Consult the rating plate, located on the right hand side of the drop down door BEFORE making the electrical connections. Ensure that the voltage reaching the plug is the same as that on the rating plate. o DO NOT REMOVE THE RATING INFORMATION ON IT IS IMPORTANT. PLATE AS THE o The moulded plug that is supplied with the appliance must be placed into an earthed and insulated socket.
will deflect steam that rises from your appliance, away from the underneath of the worktop. o The condensation strip will be located inside of your dishwasher. o Ensure that the underneath of the worktop is clean before sticking the strip to it. o Separate the backing paper away from the strip. o Stick the condensation strip to the underneath of the worktop. o IMPORTANT: Failure to attach the condensation strip could result in damage to your worktop.
Levelling the appliance o IMPORTANT: Your dishwasher must be level for it to operate properly. o Make sure that the dishwasher is supported whilst it is being levelled, otherwise it may tip over. o The rear feet can be adjusted by using the adjusting screw at the front of the appliance. o The front feet can be adjusted using a spanner. o Use a spirit level to check that the appliance is level. o Check that the appliance is level from side to side. o Check that the appliance is level from front to back.
Securing the dishwasher o The dishwasher must be secured to the worktop, this can be done in one of two ways:o Standard worktop- Secure the dishwasher to underside of the worktop by using two wood screws. the o You should screw through the holes in the brackets at the top of the dishwasher cabinet. o These screws should be fully tightened. o Marble/granite worktop- The material of the worktop will mean that it is impossible to put a screw through the underneath of the worktop.
My appliance isn’t working correctly IMPORTANT: If your appliance appears not to be operating correctly, then you should disconnect it from your mains supply and then contact the Customer Care Department on telephone number (0118) 933 6911. DO NOT ATTEMPT TO REPAIR THE APPLIANCE YOURSELF. Please note that if an engineer is asked to attend whilst the product is under guarantee and finds that the problem is not the result of an appliance fault, then you may be liable for the cost of the call out charge.
Baumatic Consumables o BC001 Degreaser for Dishwashers (200 g) o BC002 Descaler for Washing Machines and Dishwashers (200 g) o BC003 Ceramic Hob Cleaner (250 ml) o BC004 Oven Cleaner (250 ml) o BC005 Stainless Steel Cleaner and Protector (250 ml) o BC007 E-Cloth – General Purpose Cloth o BC008 Microwave Cover To order a Baumatic consumable product please call 0123 5437 244 and quote the product code. You can also order online from eshop.baumatic.co.
Technical Data Manufacturer Model Number Standard Place Settings Energy Efficiency Class (1) Annual Energy Consumption (2) Energy Consumption of the Standard Cleaning Cycle Power Consumption of Off Mode Power Consumption of Left-On Mode Annual Water Consumption (3) Drying Efficiency Class (4) Standard Cleaning Cycle (5) Program Duration of the Standard Cleaning Cycle Noise Level Installation Type BAUMATIC LTD BDW45.1 8 A 228 kWh 0.81 kWh 0.0 W 1.
United Kingdom Baumatic Ltd., Baumatic Buildings, 6 Bennet Road, Reading, Berkshire RG2 0QX United Kingdom Sales Telephone (0118) 933 6900 Sales Fax (0118) 931 0035 Customer Care Telephone (0118) 933 6911 Customer Care Fax (0118) 986 9124 Spares Telephone (01235) 437244 Advice Line Telephone (0118) 933 6933 E-mail: sales@baumatic.co.uk customercare@baumatic.co.uk spares@baumatic.co.uk technical@baumatic.co.uk Website: www.baumatic.co.uk Facebook: www.facebook.com/baumatic.
