How-To Guide

Before using or storing the product, please use the charger to charge the product.
When charging, the indicator light is blue. The LED screen will display the current
charging ratio and charging power. When the LED screen shows 100% power, it
means full charge. The charging process is about 2.5 hours. The
current power can be viewed through the LED screen.
Portable Energy Storage Power Supply
Charging mode
1.⑦press the button, the screen lights up, about 60 seconds after the screen back-
light automatically closed.
2.When ②④⑧⑨the button is pressed, the output port is turned on to power the
device.
3.When the power output port is not used, press the 2489 button to turn it off to
save power.
4.Low temperature may affect the battery capacity of the product, the product can
be charged in the temperature range of 0 ~ 40 °C, in the temperature range of-10 ~
40 °C for equipment use.
5.The first use of the product is recommended to be fully charged, to avoid the lack
of power to your use of inconvenience. After the device is fully charged, the fan will
continue to work for about 2 minutes after the charging power cord is unplugged,
which is used for cooling the device (the specific time may vary with the scene
temperature) , pay attention to prevent dust particles or foreign matter from being
inhaled into the equipment, otherwise it will easily lead to internal equipment
damage.
6.After the discharge is terminated, the device fan will continue to work to reduce
the device temperature to a reasonable temperature for about 30 minutes (the time
may vary with the scene temperature) . At the same time charge and discharge,
current more than 15A or equipment temperature is too high, will trigger automatic
power-off protection.
7.During the charging and discharging process, please connect the device with the
charging and discharging device, then turn on the charging and discharging.
Otherwise, there might be a spark.
Precautions for use
Standard charger,
about 2.5 hours
SCar charger,
about 2.5 hours
600W solar photovoltaic panel,
about 3.5hours.
(the charging time is determined by the intensity of sunlight). Support solar
photovoltaic panel MPPT function charging (12-24 V)
The above data are from the laboratory. The test data may vary due to the use
environment, use method and other factors, and the charging time will be different.
Portable Energy Storage Power Supply
When using this product, you should always follow the basic precautions, including:
a. Please read all instructions before using this product.
b. In order to reduce the risk, close supervision is required when using this product near
children.
C. The use of accessories recommended or sold by non professional product manufacturers
may lead to the risk of electric shock.
d. When the product is not in use, please pull the power plug out of the product socket.
e. It is forbidden to dismantle the product, which may lead to unpredictable risks such as
fire, explosion or electric shock.
f. Do not use damaged wires or plugs or damaged output cables to use the product, which
may cause electric shock.
g. Please charge the product in a well ventilated place. Do not restrict the ventilation of the
product in any way.
h. Please put the product in a well ventilated and dry place to avoid the risk of electric shock
due to water intrusion.
i. It is forbidden to expose the product to fire or temperature higher than 130 ° C, which may
lead to fire, explosion and other safety accidents.
j. It is forbidden to use or place the product under high temperature (direct hot sunshine or
hot car interior), otherwise the internal battery may overheat, catch fire or function failure,
shorten the service life and other risks.
k. Please charge the product every three months to prevent the battery from running out.
充电方式
1. Can the product be brought on the plane?
No, because this product is a lithium battery product. According to the interna-
tional air transport standard regulations, carrying lithium battery products can
not exceed 100wh.
2. If the power of the equipment is within the rated output
power range of the product, it cannot be used?
a. The power consumption of the product is less than 20%; it needs to be
supplemented.
b. When some equipments start, the products which are larger than the peak
value of rated power cannot be used;
3. Why is there sound when using it?
The product adopts air cooling system, and the built-in fan is better to help
product heat dissipation. It is normal to have slight noise when using.
4. Is the charger heating normal when charging?
Charging charger heating is a normal phenomenon, standard charger in line
with national safety standards, you can rest assured to use!
Certificate
Inspection date:________
Inspector:_____________
QC pass
The product
cannot be charged
The product
has no output
With device
output interrupt
Fault phenomenon
Troubleshooting Solutions
1. The connection line between the equipment and the product
is not plugged in properly
2. The output port switch is not turned on
3. Low power consumption
4. There is no output after eliminating according to 1.2.3 above
Make the equipment well connected with the product
Turn on the port output switch, and the indicator light
will be on
Charging the product
If the product is broken, contact the after-sales
department for handling
1. The charger and product are not in good contact with the
mains power supply (the charging indicator is not on at this time)
2. The contact is good, but the charging indicator is not on
3. If the charging indicator light is on, it still can't be charged
Check whether the charger and product are in good
contact with the mains power
If the charger is broken, please contact after-sales service
If the product is broken, please contact after-sales service
Select higher power energy storage products
It is not a product problem.
It is recommended to replace the equipment.
If the product is broken, contact the after-sales department
for handling
Warnings and precautions FAQ Warranty and contact information
Guarantee to the user that under the normal use of the product, there will be
no defects affecting the use of the product due to the process and materials;
This warranty statement sets forth the full and exclusive warranty obligations of
the products, and we will not assign or authorize anyone to assume any other
responsibilities for us in connection with the products we sell.
Defects liability period
The warranty period is one year. In all cases, the warranty period starts from the
date of purchase by the consumer. In order to determine the starting date of
the warranty period, it is necessary to provide the consumer's purchase
certificate or other reasonable documentary evidence.
The following conditions are not covered by the warranty
1. The appearance of the product is damaged after use;
2. Disassembly and repair by non staff members without permission;
3. Product performance failure caused by human factors.
4. Damage caused by irresistible factors such as natural disasters, lightning and
accidents.
How to get warranty service
Contact your local dealer or brand
Portable Energy Storage Power Supply
Equipment failure, please restart
AC Output Power
Output Power （AC/DC）
Output Frequency 50Hz
Output Frequency 60Hz
AC working indicator
USB working indicator
DC working indicator
Wireless charging working
Cooling Fan working
Description of icon work
FCC Statement
This device complies with part 15 of the FCC Rules. Operation is Subject To the following
two conditions:
(1)This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
Changes or modifications not explicitly approved by the party responsible for compliance could void
the user's authority to operate this equipment.
Note: this equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates, uses
and candidate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of
the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV technician for help.
The equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. During the operation of device a distance of 15 cm surrounding the device and 20 cm
above the top surface of the device must be respected.