Instruction Manual

YMA
YM-005/YM-007
Taizhou Yima Bathroom Remote Control Instruction Manual
Remote control panel
Battery installation
Remote control failure analysis
Remote control code
1.Unplug the main unit.
1.Open the remote control battery compartment
back cover
2.Install battery (7 batteries, 2 sections)
3.Install the remote control battery compartment
back cover
Warn
This device complies with Part 15 of the FCC rules. Operation is subjected to the follow-
ing two conditions: (1) this device may not cause harmful interference, and (2) this dev-
ice must accept any interference received, including interference that may cause undesired
operation.
Changes or modifications not expressly approved by the party responsible for compliance c-
ould void your authority to operate the equipment.
This device complies with Industry Canada’s licence-exempt RSSs.Operation is subject to
the following two conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including interference that may cause unde-
sired operation of the device.
The distance between user and products should be no less than 20cm
Cet appareil est conforme aux CNR exemptes de licence d'Industrie Canada.Son fonctionnem-
ent est soumis aux deux conditions suivantes :
( 1 ) Ce dispositif ne peut causer d'interférences ; et
( 2 ) Ce dispositif doit accepter toute interférence , y compris les interférences qui p-
euvent causer un mauvais fonctionnement de l'appareil.
la distance entre l'utilisateur et les produits devraient être au moins 20 cm
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reaso-
nable protection against harmful interference in a residential installation. This equipm-
ent generates, uses and can radiate radio frequency energy and, if not installed and used
in accordance with the instructions, may cause harmful interference to radio communicati-
ons. However, there is no guarantee that interference will not occur in a particular ins-
tallation. If this equipment does cause harmful interference to radio or television rece-
ption, which can be determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the re-
ceiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
Children/
Pulsate
Female/
Pulsate
Stop/Reset
High/Low
Water Temp
Seat temp
Lower Lid
Lower Seat
Night Light/
Auto Distance
Setting/
Pulsate
Back/OFF
Front/ON
Water Pressure
Hot/Cold
Wind Temp
Power ON/OFF
Flush/
Auto Setting
Lift Lid
Lift/Lower Seat
Rear/
Pulsate
Dryer
Power
ON/OFF
Night Light/
Auto Distance
Flush/
Auto Setting
Wind Temp Water Temp Seat Temp
Hot/Cold Water Pressure High/Low
Back/OFF
Stop/Reset
Setting/Pulsate
Rear/
Pulsate
Female/
Pulsate
Children/Pulsate
Dry
Front/ON
Lift Lid
Lift/Lower Seat
Lower Lid
Lower Seat
※Note: The remote control can be turned on - off - on - off - on - off - no other buttons can be
pressed during shutdown.
2.Remote control power switch key short
press to boot, long press 3 seconds to shut
down, press again shortly to boot, press and
hold again for 3 seconds to shut down, press
again shortly to boot, press and hold again
for 3 seconds to shut down, (switch 3 times) last remote control It is in the
off state.
3.The host is plugged in, only the first 15 seco-
nds is the valid code period.
4.When the main unit is powered on, press and hold the power button of the
remote control for a long time of about 4 seconds. When the remote control
position lamp and the top light flash together 3 times, the signal is released.
5.Test the remote control, if the control is
normal, the code is successful. If it is not
successful, repeat steps 1~4.
power
Power
ON/OFF
Night Light/
Auto Distance
Flush/
Auto Setting
Wind Temp Water Temp Seat Temp
Hot/Cold Water Pressure High/Low
Back/OFF
Stop/Reset
Setting/Pulsate
Rear/
Pulsate
Female/
Pulsate
Children/Pulsate
Dry
Front/ON
Lift Lid
Lift/Lower Seat
Lower Lid
Lower Seat
Power
ON/OFF
Night Light/
Auto Distance
Flush/
Auto Setting
Wind Temp Water Temp Seat Temp
Hot/Cold Water Pressure High/Low
Back/OFF
Stop/Reset
Setting/Pulsate
Rear/
Pulsate
Female/
Pulsate
Children/Pulsate
Dry
Front/ON
Lift Lid
Lift/Lower Seat
Lower Lid
Lower Seat
Power
ON/OFF
Night Light/
Auto Distance
Flush/
Auto Setting
Wind Temp Water Temp Seat Temp
Hot/Cold Water Pressure High/Low
Back/OFF
Stop/Reset
Setting/Pulsate
Rear/
Pulsate
Female/
Pulsate
Children/Pulsate
Dry
Front/ON
Lift Lid
Lift/Lower Seat
Lower Lid
Lower Seat
When the reset command is started, all the lights on the remote control are lit
for 3 seconds, indicating that the parameter reset is successful. The factory
gear parameters are as follows:
The water temperature is 0, the wind temperature is 0, the seat temperature is
0, the pipe is 4, the water is 4, and the night light is on.
The automation settings are:
Long press the remote control 4 seconds for the
parameter reset command
Parameter reset or factory reset
Energy saving
off
Automatic
flushing on
Flush before
drying
Automatic
flip on
Automatic
opening
Personality cleaning is set to:
The buttocks are cleaned for 150 seconds, the water temperature is 4, the wind
is 4, the tube is 4, the water is 4, the reciprocating is open, the strong and weak
is closed, and the hot and cold is closed.
stop/reset
Power
ON/OFF
Night Light/
Auto Distance
Flush/
Auto Setting
Wind Temp Water Temp Seat Temp
Hot/Cold Water Pressure High/Low
Back/OFF
Stop/Reset
Setting/Pulsate
Rear/
Pulsate
Female/
Pulsate
Children/Pulsate
Dry
Front/ON
Lift Lid
Lift/Lower Seat
Lower Lid
Lower Seat
Check if the remote control
batteries are too low
Check if the remote control
panel has water droplets
The remote control displays
normally and the machine
does not beep
Please replace the battery
Connect the remote control with reference to this manual
Wipe the droplets with dry cloth
Start the kid wash mode
Under kid wash mode, use remote control to start
child lock function and press the stop button to stop it.
Failure analysis Failure Handling
(When replacing the new remote control or the remote control cannot control the machine, please follow
the steps below to carry out the remote control code (normally the code is completed at the factory))