Owner's Manual

ManualsBrandsBarton Instrument Systems ManualsElectronicsTankscan Controller Radio Module

TankScan™ W-Series

WC2 Controller

Installation Manual

Version 99L15xz

ID#11680

4/2001

Introduction

The TankScan Wireless Level System Controller includes a radio/modem

enclosure, an antenna, and an AC power adapter.

System Installation Steps

A. Install Controller (distance & line-of-sight location predetermined).

B. Install monitor(s) on the tank(s)

C. Install fill indicator(s) at a accessible location near the fill point.

D. Install software on host PC

E. Power up and configure the Controller

F. Power up the monitor(s) and fill unit(s).

Controller Installation

NOTICE

Do not install Controller near any RF sources (TV, Radio, etc.). Interference

from such devices can cause data loss and Controller malfunctions.

1. Place Controller on stable flat surface or mount on

wall.

a. If desired, install the self-adhesive rubber feet.

b. To wall mount, attach mounting plate to bottom of

enclosure using supplied screws, then attach the

assembly to the wall with the antenna connector

facing up.

Note: Controller must be within reach of the power source/outlet,

phone jack (if used) and PC (if direct

connection is used).

2. Attach Antenna to Controller (pointed upward).

Note: Ant. connector has left-handed thread.

3. Connect Phone Line, using supplied RJ11 cable.

Plug one end into the Controller and the other

into the wall phone jack. If a phone is needed, plug it into the second RJ11

socket on the Controller. Note: RJ11 sockets are in parallel, either can be

used for line.

CUS

Mounting Bracket

See Dimensions

on Page 4.

RS232

Power

Antenna

Phone

Line

CAUTION

To reduce the risk of fire, use only No. 28 AWG or larger telecommu-

nications line cord.

PRELIMINARY

Summary of content (8 pages)

PAGE 1
TankScan™ W-Series WC2 Controller Installation Manual C US Version 99L15xz ID#11680 PRELIMINARY 4/2001 Introduction The TankScan Wireless Level System Controller includes a radio/modem enclosure, an antenna, and an AC power adapter. System Installation Steps A. B. C. D. E. F. Install Controller (distance & line-of-sight location predetermined). Install monitor(s) on the tank(s) Install fill indicator(s) at a accessible location near the fill point.
PAGE 2
Controller Installation (continued) 4. Plug in the appropriate Power Adapter (US or EU type included, per order). Plug the barrel-ended connector into Controller and the 3-prong plug into an unswitched AC outlet. (US) Power Adapter (EU) Power Adapter 5. Check front panel indicator lights to make sure unit is operating. Front Panel Indicator Lights & Auto Answer Switch The AUTO ANSWER switch sets the modem's answer mode.
PAGE 3
Symbol Information The following symbols may be used in this manual or on the instrument: Technical Support/Warranty Service/Repair US: 626-961-2547 • Canada: 403-291-4814 • Europe: 441243826741 Specifications Operating Temperature ........... +32°F to +140°F (0°C to +60°C) Enclosure ............................... NEMA-1/IP30 - Indoor Use Only Safety Ratings ......................... UL1950, CSA950, and EN60950 Flame Class Rating .................. UL94V-0 Power Requirements ...............
PAGE 4
Dimensions Replacement Parts List Part Description Part Number AC Power Adapter (US) .......... TL10-2009T Antenna (standard) .................. TL10-2004T Optional Outdoor Antenna (with mount): 20-ft. cable ......................... WC20-2046B-1 30-ft. cable ......................... WC20-2046B-2 Telephone Cable (10') .............. TL10-2007T PC Cable ...............................
PAGE 5
COMPLIANCE STATEMENTS FCC COMPLIANCE STATEMENTS FOR WC20 FCC PART 68 NOTICE This equipment complies with FCC Part 68 rules. The FCC registration number and Ringer Equivalent Number (REN) are printed on a label attached to the bottom of the enclosure. You must, upon request, provide this information to your telephone company. The REN number is used to determine the maximum number of devices that may be connected to the phone line and still have all those devices ring when your number is called.
PAGE 6
CANADIAN COMPLIANCE STATEMENTS FOR WC20 The Industry Canada (IC) label identifies certified equipment. This certification means that the equipment meets certain telecommunications network protective, operational, and safety requirements. The department does not guarantee the equipment will operate to the user’s satisfaction.
PAGE 7
EU CTR21 STATEMENT FOR WC21 Network Connection This apparatus is suitable for connection for direct 2 wire connection to the PSTN and indirect 2 wire connection to the PSTN via compatible extensions on a PABX system. Facilities The WC21 Controller's modem has been approved for use with the following facilities: • Signalling to the PSTN using DTMF signalling only • Auto-answering • Auto-call clearing • Data modem The modem should be set up for blind dialling (e.g., dial after delay, no dial tone detection).
PAGE 8
Order Code TankScan W-Series WC2_ Controller CONFIGURATION ORDER CODE WC2 # - X NorthAmerican, Internal A # X # X RADIO North America (902-928 MHz) 0 Europe (869.7-870 MHz) 1 MODEM European, Internal (CTR21) C Future (Option) None 0 HEATER (Option) None N w/Heater H ANTENNA Local, Right Angle (Mounts on Controller) Remote, Bracket Mount 1 3 POWER 110 VAC/60 Hz (North American Plug) A 220 VAC (UK Plug) B 220 VAC (European Plug) C Barton Instrument Systems, LLC 900 S. Turnbull Canyon Rd.