User Manual Pegasus 70xx Series Pegasus 7000 Type G7-C010-*Q*1/0000 Pegasus 7010ex Type 17-C110-*Q*1/0000 Pegasus 7020ex Type B7-C210-*Q*1/0000 Document No. 11-C110-7D0001 Status: 17. February 2010 Technical subject to change! Contents GmbH Max-Eyth-Straße 16 97980 Bad Mergentheim Germany Page English 1 - 44 Appendix EC-Declaration of Conformity Phone: +49 7931 597-0 Fax: +49 7931 597-119 Contact: info@bartec.
Safety Notes on this manual The user manual is a constituent part of the product and must be kept in the direct vicinity of the device and accessible at all times to installation, operating and maintenance personnel. It contains important notes, safety instructions and test certificates which are necessary for perfect functioning when the devices are being operated and handled. It is written for technically qualified personnel. Read carefully before putting the devices into operation.
Safety Handing the Product The documents are currently available in German and English. The product described in this manual has been tested and left the factory in perfect condition as regards meeting safety requirements. To maintain this condition and ensure that this product operates perfectly and safely, it may be used only in the manner described by the manufacturer.
Safety Safety Instructions Safety instructions and warnings are specially highlighted in this manual and marked by symbols. The safety instructions and warnings are assigned to the individual work steps. Careful handling and consistent observation of the instructions will prevent accidents, personal injuries and damage to property. Read carefully before putting the devices into operation.
Contents 1 Product Description....................................................................................................................................3 1.1 Definition .........................................................................................................................................3 2 Specification Pegasus 70xx series............................................................................................................5 2.
Safety 4 5 Commissioning .........................................................................................................................................16 4.1 Purchased parts in packages........................................................................................................16 4.2 Functional Parts of the device.......................................................................................................16 4.3 Fastening and Changing the belt clip ......................
Pegasus 70xx series User Manual 1 Product Description 1.1 Definition PEGASUS 70xx series - the All in One Solution PEGASUS is the new mobile phone/online tracking system for industry. It is perfect for utilization in extreme conditions in the chemicals and pharmaceuticals industries and also in the oil and gas industry. PEGASUS is robust, simple to use and comes in an attractive distinctive design. „Made by BARTEC“ stands for top quality, long product availability and excellent service.
Pegasus 70xx series User Manual User-friendly keyboard The keyboard is generously dimensioned and offers enough space for steady operation, even with gloves. To prevent operating errors, all keys give tactile feedback in the form of a click. Quad Band GSM Module PEGASUS knows no boundaries. With the Quad Band GSM module (850/900/1800/1900 MHz) the device is ideally equipped for utilization on all continents.
Pegasus 70xx series User Manual 2 Specification Pegasus 70xx series 2.1 Specification Pegasus 7000, type G7-C010-*Q*1/0000 2.1.1 2.2.1 Marking Type G7-C010-*Q*1/0000 Marking CE marking Standards EN 60950-1 Directives - Technical data Display OLED color display Networks Quad Band GSM 850/900/1800/1900 MHz Dimensions (Height x Width x Depth) 155 mm x 59 mm x 27 mm Weight approx.
Pegasus 70xx series User Manual 2.2 Specification Pegasus 7010ex, type 17-C110-*Q*1/0000 2.1.2 Ex protection marking Type 17-C110-*Q*1/0000 Ex protection type (ATEX Zone 1 / 21) II 2G Ex ib IIB T4 II 2D Ex ibD21 T130° Product marking Certification Demko 10 ATEX 0911055X Ex protection type (IECEx) Ex ib IIB T4 Gb II 2D Ex ibD21 T130° Certification IECEx UL 10.
Pegasus 70xx series User Manual 2.3 Specification Pegasus 7020ex, type B7-C210-*Q*1/0000 2.1.3 Ex protection marking Type B7-C210-*Q*1/0000 Ex protection type (ATEX Zone 2 / 22) II 3G Ex ib IIC T4 II 3D Ex ibD22 T130° Product marking Certification Demko 10 ATEX 147282X Ex protection type (IECEx) II 3G Ex ic IIC T4 Gc II 3D Ex icD22 T130° Certification IECEx UL 10.
Pegasus 70xx series User Manual 2.4 Product Marking Ex Logo Only printed on the displayed Ex versions of the Pegasus 70xx series. Pegasus 7010ex Pegasus 7020ex Differentiation of colors Pegasus 7000 with grey display border Pegasus 7010ex with blue display border Pegasus 7020ex with green display border Type label Technical data subject to change without notice.
Pegasus 70xx series User Manual 3 Safety and Security For an efficient and safe operation of your Pegasus 70xx series, it is important that you read this information before use! Note 3.1 Your Pegasus 70xx series is one of the most exciting and innovative electronic products ever developed. With it, you can stay in contact with your office, your home, emergency services and others, wherever service is provided.
Pegasus 70xx series User Manual Do not open or charge the devices and do not exchange any data through the listed equipment in the hazardous area! The device my not be opened by the user outside the hazardous area either! The user may not make any alterations to the device. Do not exchange or replace components and do not retrofit any components on internal plug connectors or slots. If components other than those specified are used, the protection against explosions can no longer be assured.
Pegasus 70xx series User Manual The battery should only be used for the purposes stated in the user manual and is only suitable for use with Pegasus 70xx series. The battery should not be exposed to any temperatures higher than +60 °C. Do not place the battery on, in or near fires, apparatus that provide heat, or other hightemperature locations. Do not place the battery in direct sunshine or use or store the battery inside cars in hot weather.
Pegasus 70xx series User Manual 3.4 Health and Safety recommendations Use only approved accessories. All components must be dry before they may be connected to an external power supply. It is only permitted to use by BARTEC approved accessories for charging or/and data communication.
Pegasus 70xx series User Manual 3.7 Electronic devices Most electronic equipment, for example in hospitals and motor vehicles is shielded from RF energy. However, RF energy may affect some malfunctioning or improperly shielded electronic equipment. 3.8 Vehicle electronic equipment Check with your vehicle manufacturer’s representative to determine if any on board electronic equipment is adequately shielded from RF energy. 3.
Pegasus 70xx series User Manual 3.13 Potentially explosive atmospheres Turn your Pegasus 70xx series device OFF when in any area with a potentially explosive atmosphere. It is rare, but your modems or their accessories could generate sparks. Sparks in such areas could cause an explosion or fire resulting in bodily injury or even death. Areas with a potentially explosive atmosphere are often, but not always, clearly marked.
Pegasus 70xx series User Manual Statement according to FCC part 15.19: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: ■ ■ this device may not cause harmful interference, and this device must accept any interference received, including interference that may cause undesired operation. Statement according to FCC part 15.21: Modifications not expressly approved by this company could void the user's authority to operate the equipment.
Pegasus 70xx series User Manual 4 Commissioning 4.1 Purchased parts in packages Before commissioning the devices, check that all components and documents are there. ■ ■ ■ ■ ■ ■ 4.
Pegasus 70xx series User Manual Screw for fastening the belt clip (type K20x8 WN5452-Torx-1) Belt clip Battery cover Type label Figure 6: Pegasus 7010ex rear side Micro SD card slot SIM card slot Hard shutdown Mini USB interface Figure 7: Pegasus 70xx cover Clock Phone settings Signal strength level (5 bars) OK for the left soft key SMS settings General settings Battery Figure 8: Pegasus 70xx start screen Technical data subject to change without notice.
Pegasus 70xx series User Manual 4.3 Fastening and Changing the belt clip The belt clip may only be fastened or changed outside the hazardous area! Danger! ¨ Put the belt clip into the slot of the back of the Pegasus 70xx ¨ Turn the belt clip in position as shown in figure 10 ¨ Tighten the screw (type K20x8 WN5452-Torx-1) to fix the belt clip on the Pegasus 70xx. Figure 9: Pegasus 70xx without belt clip Figure 10: Pegasus 70xx fastening belt clip Technical data subject to change without notice.
Pegasus 70xx series User Manual 4.4 Inserting and changing the battery Danger! Charge and change battery only in an area known to be non-hazardous. Use only BARTEC Models what are listed in chapter “3.4 Health and Safety recommendations” for charging and communication or equivalent. ¨ Turn your Pegasus Off before you change the battery ¨ Loosen the screw (type K20x8 WN5452-Torx-1) on the belt clip ¨ Remove the belt clip as described in chapter 4.3.
Pegasus 70xx series User Manual 4.5 Charging the battery The battery may only be charged with listed chargers outside the hazardous area! Danger! ¨ Open the cover to access the connections. ¨ Connect the charger cable to the mini USB slot as shown on figure 14. ¨ The charging status of the battery is shown on the right side of the screen. ¨ After charging, remove the mini USB cable and close the cover.
Pegasus 70xx series User Manual 4.6 Inserting the Micro SD-card The Micro SD-card may only be inserted or changed outside the hazardous area! Danger! ¨ Turn your Pegasus Off ¨ Open the cover to access the connections. ¨ Insert the micro SD-card into the slot as shown in figure 16. ¨ Close the cover. Figure 15: Pegasus 70xx open cover Figure 16: Pegasus 70xx micro SD card slot Technical data subject to change without notice.
Pegasus 70xx series User Manual 4.7 SIM card The Micro SD-card may only be inserted or changed outside the hazardous area! Danger! ¨ Turn your Pegasus Off ¨ Open the cover to access the connections. ¨ Insert the SIM card into the slot as shown in figure 18. ¨ Close the cover. Figure 17: Pegasus 70xx open cover Figure 18: Pegasus 70xx SIM card slot Technical data subject to change without notice.
Pegasus 70xx series User Manual 5 Operation 5.1 Getting started You are now ready to use your Pegasus 70xx for the first time. Switch on the Pegasus by pressing the Power ON/OFF key. A start screen appears. When you switch on your phone for the first time, you must configure it with various settings that will remain by default until you choose to modify them.
User Manual 5.3.1 Pegasus 70xx series ■ The 2-way navigation key is for the selection of a menu entry. ■ The left soft key is used to go from a menu to a sub-menu. ■ The right soft key is used to go from a sub-menu to a higher-level menu. General Settings Use the 2-way navigation key to select the settings menu and to enter the press the left soft key menu for customising your Pegasus 70xx. Different menus are available customising your Pegasus 70xx.
Pegasus 70xx series User Manual 5.1.3.2 Sound volume Use the 2-way navigation key to change the volume and confirm with the left soft key . loud low 5 5.1.3.3 You can exit the sub-menu by pressing the right soft key . Vibration Use the 2-way navigation key to select Vibration On or Off and confirm it with the left soft key . You can exit the sub-menu by pressing the right soft key . 5.1.3.4 Geofence Use the 2-way navigation key to select Geofence On or Off and confirm it with the left soft key .
Pegasus 70xx series User Manual 5.4.1 Key lock You can lock and unlock the keypad with keypad shortcuts. To lock or unlock, press the right soft key and the star key . If the Pegasus 70xx is not in use for longer than 1 minute, the device will switch to screen saving mode and lock the keys. When the device is locked and you press a key, the Press appears. and key message Locked keys: You will see the screensaver. 5.2 Phone settings 5.1.
User Manual 5.3.2 Pegasus 70xx series Starting dialing from the menu Use the 2-way navigation key to select phone menu and press the left the soft key to enter the menu. Use the 2-way navigation key to select the “Dialpad” menu and press the left soft key to enter the sub-menu. Dial a number and press the left soft key to start the dialling process. You can cancel or stop the call by pressing the right soft key . 5.4.
User Manual Pegasus 70xx series Use the 2-way navigation key to select a contact in your “Phonebook” or the “SIM card”. First press the left soft key sub menu of the contact. to show the You can cancel or stop the call by pressing the right soft key . Use the 2-way navigation key a option in your “Phonebook” to select to start the Press the left soft key dialling process, write a message or delete the Phonebook entry. You can exit the sub-menu by pressing the right soft key . 5.5.2 Receiving call 5.
User Manual Pegasus 70xx series Use the 2-way navigation key to select phone menu and press the left the soft key to enter the menu. Use the 2-way navigation key to select the “Last caller” menu and press the left soft key to enter the sub-menu. 5.9.2 Known call The name and the number of the incoming call appear on the screen. to start the Press the left soft key dialling process. You can exit the sub-menu by pressing the right soft key . 5.10.
Pegasus 70xx series User Manual Save: Type the name of the contact and save the contact in your “Phonebook” by pressing the left soft key . 5.3 5.1.3 SMS (Short Message Service) Settings SMS Options Use the 2-way navigation key to select “Message” menu and press the the left soft key to enter the menu. Use the 2-way navigation key to select your option in the “Message” menu and press the left soft key to enter the sub-menu. ■ ■ 5.2.3 New message Write a new message and send to a contact/s.
User Manual Pegasus 70xx series Enter the text in the field. Press the left soft key message Press the right soft key character entered. 5.3.3 to send the to delete the last Incoming All messages received are stored in this menu. Use the 2-way navigation key to select the “Incoming” menu and press the left soft key to enter the menu. Technical data subject to change without notice.
User Manual Pegasus 70xx series Use the 2-way navigation key to choose a message and press the left soft key to read it. ■ ■ ■ Messages are listed chronologically. The newest message is listed first. Unread messages are highlighted with a bold font. Options: ■ ■ ■ ■ Read the message. Delete the message. Forward the message. Answer the message. You can exit the sub-menu or the message by pressing the right soft key .
Pegasus 70xx series User Manual 6 Maintenance, Inspection, Repair Caution! Only trained and qualified personnel may commission and do maintenance work on the Pegasus 70xx series! Trained qualified personnel are people who are familiar with the installation, assembly, commissioning and operation of the Pegasus 70xx series, have been instructed about the risks and have the appropriate qualifications by virtue of the work they do.
Pegasus 70xx series User Manual 7 Disposal Battery packs should not be disposed of in general household waste. Observe the local waste disposal regulations, which you can find out about contacting your local authority. All electrical and electronic products should be disposed of separately from the municipal waste stream via designated collection facilities appointed by the government or the local authorities.
EC-Declaration of Conformity Technical data subject to change without notice.
Technical data subject to change without notice.