DRAFT TECH1000 Tyre Pressure Monitoring System Tool USER GUIDE Camera Rubber housing On/Off: hold down for a few seconds Press once for more options Display Home: Back/Esc returns to Home menu USB port Bartec Auto ID Ltd. Mini USB SW Version: R.59.
FOREWORD Dear customer, Thank you for having chosen one of our tools. We are certain that it will give the utmost satisfaction and be a great help on the job. Please become fully familiar with the instructions in this user’s manual. It should be kept ready to hand for consultation whenever required. Important: Visit the Bartec website to register your tool. This enables you to download the latest tool software and to receive notification of updates to the tool’s software.
LIST OF CONTENTS User Guide ....................................................................................... 1 Foreword .......................................................................................... 2 List Of Contents ................................................................................ 3 Important Notices ............................................................................ 4 Safety Precautions............................................................................
IMPORTANT NOTICES SAFETY DEFINITIONS All Danger, Warning, Important, and Note messages must be followed for your safety. These safety messages are in the following form DANGER: Means you may risk possible loss of life. WARNING: Means you may risk possible bodily harm. CAUTION: Means you risk damage to the vehicle or the tool. These safety messages cover situations Bartec is aware of. Bartec cannot know, evaluate and advise you as to all the possible hazards.
TECH1000 • • • • • User Guide R.59.0 2019 Do not dispose of this equipment as miscellaneous solid waste but arrange to have collected separately. The re-use or correct recycling of electronic equipment (EEE) is important in order to protect the environment and human health. In accordance with European Directive WEEE 2002/96/EC, special disposal points are available for waste electrical and electronic equipment.
TECH1000 User Guide R.59.0 2019 BEFORE GETTING STARTED 1. Charging NOTICE: Only use the power supply that is included in the TECH1000 tool kit to charge this tool. The use of un-approved power supplies may damage it and will void the tool warranty. 2. Registration The Bartec TECH1000 can be registered at https://tools.bartecautoid.com/ . Follow the on-screen prompts filling in the information and tool serial number.
TECH1000 User Guide R.59.0 2019 CHARGING TOOL The TECH1000 is shipped with a charged battery. It is recommended that the tool is charged 2+ hours before first use. For optimum performance, always keep it sufficiently charged. When there is an insufficient amount of power remaining in the battery, the TECH1000 will flash its battery icon for two seconds, save all of the TPM Data and then power itself off.
TECH1000 User Guide R.59.0 2019 NEW SERVICE All menu items marked with an asterisk (*) are mandatory fields. VIN: Select whether the VIN should be read from the ECU or by the integrated camera. Choose from the following options: ▪ ▪ ▪ ▪ OBD 2D code Standard Barcode Inverted Barcode Registration: Select whether the Registration should be typed in manually or captured by the integrated camera.
TECH1000 User Guide R.59.0 2019 Connect the OBD Module to the Vehicles OBD II port and connect the tool to the module. In case of any problems the troubleshoot menu will help you to obtain a connection. STEP 2: SENSOR ACTIVATION/ TEST Tool Positioning Do NOT touch the metal rim. The tool needs to be pointed at the sensor through the tire. 1. LF activated sensors To test a sensor the tool should be placed alongside the valve stem and the ‘Test’ symbol needs to be pressed.
TECH1000 User Guide R.59.0 2019 POSSIBLE READING SCENARIOS Note that if a faulty TPM sensor has been replaced, some methods of relearn procedures will need to be followed, as explained later in this manual. To receive further Sensor Information tap on one of the symbols next to the wheel position. [SCREENSHOT] Successful Sensor Read TPMS sensor was successfully activated and decoded. Displays pressure (in Bar or PSI) at Wheel location. [SCREENSHOT] Failed Sensor Read No Sensor Activation or Decoding.
TECH1000 User Guide R.59.0 2019 STEP 3: TREAD DEPTH AND PRESSURE MEASUREMENT In this step of the menu the tool tries to establish a connection to a Tap100 Tread depth and Pressure measurement Tool. To set up the connection, please turn on the TAP100 and wait for it to boot to the Main Menu. Keep both tools within 15 feet of one another and wait for the Tech1000 to set up the connection automatically.
TECH1000 User Guide R.59.0 2019 STEP 6: RELEARN OBD Relearn Watch: Read: Select Read to get a detailed instructions on how to relearn. Select: If you press select the OBD connection is established and automatically relearns the vehicle sensors. After your Service is completed you can upload your report to the Service Centre. If you select auto upload in the Service Centre Settings your report is automatically uploaded to the cloud. RKE Test the remote keyless entry system of the customer’s vehicle.
TECH1000 User Guide R.59.0 2019 TRAINING In the Training Menu you can watch tutorials and Demonstrations of your tool and other tools of the Bartec range. Tap on the Play symbol to start the video. You can turn the volume up using the bar at the downside of the video.
TECH1000 User Guide R.59.0 2019 APPENDIX APPENDIX A: Vehicle Identification Number (VIN) When using the TECH1000 tool, it is important for the user to verify the Model Year to help insure looking for that proper sensor and using the proper vehicle COMs when 10th Digit in necessary. Year VIN By using the vehicles VIN and locate the 10th digit from the left the user can in most cases accurately determine that vehicle’s Model Year. Take that digit and reference the chart on this sheet.
TECH1000 User Guide R.59.0 Flashing Light: System Problem 2019 System problems can range from faulty sensor(s) to sensors on the vehicle that haven’t been learned to that vehicle. APPENDIX C: MODES and MODE CHANGING Sensors can have many different “modes” when they have been read, such as Learn, Tool LF, YD Sleep, YD Rest, Hi Norm Dly. Some of those are called sleep mode to preserve battery life.
TECH1000 User Guide R.59.0 2019 TECHNICAL SPECIFICATION Power Supply 6000mAh Lithium Polymer rechargeable battery, not user serviceable Max power consumption 1.5W Schrader TPM, 0.5W all others Display LED colour touchscreen, 4.3 inch, 800x480 Input/output Mini-B style USB used to Connect to PC for firmware update and audit file download.
