Barlus Camera 316L stainless steel installation Guide Shenzhen zhiyong Industry Co., Ltd. If you have any questions, please contact our technical team email. E-mail: 992091370@qq.com If more information is needed, please check first on http://www.cn-rov.
1 1 introduction 5 2 1.1 Accessories 6 Please check the supplied accessories for completeness before starting the assembly. If components are missing or damaged, please contact us immediately. Component name number Stainless steel IP network camera Camera mount installation Guide Waterproof connection cable 1 1 1 10 metres 3 7 4 8 Figure 2-1 Connectivity 1.
Assembly note: When installing the camera, please ensure that the junction box is located outside of the water surface and is installed in an environment protected from rainwater, e.g. by using a junction box. 5. Perform the steps shown in Figure 3-1 to adjust the IP address change and network settings. Figure 2-2 assembly principle 3 Connection to the network Figure 3-1 Display of search results a. After starting the Device Manager, press the "IP Search" button. b.
If the Microsoft Internet Explorer browser is your standard browser, then click on the "WebBrowse" button to start Internet Explorer for the selected camera. If not then enter the corresponding camera IP address manually in the IE browser input field. Example: http://192.168.1.88 Note: If you are using Windows 10, you will find IE11 in the “Start” menu and then in the “Windows Accessories” folder. When the start page is called up with the IE browser for the first time, the request below to install "WebMS.
Enter the standard user “admin”. The factory-set password is “admin123456”. Please change the password after completing the installation in the menu: Config> System> User Manage Replay - The playback function is only supported for video clips stored locally on the PC, as the camera does not have an SD card or hard disk for recording. Config - Web menus for parameterizing the camera functions alarm - Text display of alarms that have occurred, e.g. through motion detection.
Control of the two light sources The two available light sources can be controlled using the arrow keys. There is an infrared light source (IRLED) whose use requires the camera to switch to black / white image mode. The white light can also be used in color operation of the camera. 1. Full screen display - the mode is ended with the "Esc" key or by double-clicking the right mouse button. 2. Switching the displayed live image aspect ratio between 4: 3 and 16: 9 3.
The brief instructions only cover a few of the main setting options for the camera functions. If the selected NTP server uses a different port than the standard port 123, adjust this accordingly. The frequency of the synchronization can be set using the interval time setting. The camera will restart to apply the time / date change. Setting date time To set the correct time / date, follow the menu structure: Config> System> SystemTime.
Motion detection settings To call up the menu for motion detection, follow the menu structure: Config> Alarm Settings> Motion Detection. 1. With standard, the entire image content is used for motion detection. If only a part of the area is to be used, press the “Motion area set” button followed by the “Clear” button. Now up to four fields can be set for motion detection using the mouse. 2. The detection sensitivity (Sensitivity) can be set in 5 levels (1 = lowest - 5 = highest). 3.
Quality: If the "Advanced" setting is deactivated, the image quality can be set here in three levels. Advanced: By setting / removing the checkmark, further setting options for limiting the data rate (bandwidth) and frame rate are activated / deactivated. Control over bit rate: Select between CBR and VBR modes. Note: The CBR mode is a fixed bit rate setting (bandwidth limit) that is always transmitted.
7. Click the symbol in the top right corner to add a new camera to the app. Enter a name for the camera in the first line. Scan the QR code on the camera nameplate by clicking the QR symbol or enter the number manually using the keyboard. You can also find this information in the camera's web interface under the menu: Config> Network Settings> Mobile. User is admin and the default password is admin123456. If the password has already been changed, please enter it. Please set the number of video streams to 1.
the mobile device. The control directions UP / DOWN serve to switch the white light or the IR light on / off and to control the light intensity in several stages. Selection for multi-image display / Switching between high-definition HD video stream (High) and low definition SD video stream (Clear). The LEFT control direction switches the camera to infrared (IR) or neutral * mode. The control direction RIGHT switches the camera to white light or neutral * mode.
Figure-11 12