Instructions / Assembly

ManualsBrandsBarkan ManualsElectrical13 - 83 inch Tilt Elegant Tripod Floor Stand TV Mount Black Patented to Fit Various Screen Types

Table Of Contents

Default Section

Page 1

Elegant Telescopic Tripod TV Mount

Floor Stand

Tilt

Warning! Ignoring the safety and assembly instructions may result in SERIOUS OR FATAL INJURIES

from tip over or the falling of the product and the electrical appliances. Opening the package represents

your undertaking to closely read and follow the instructions. This product is not intended for use in public

places. For Safety Instructions, warranty and further information, go to: www.barkanmounts.com ›

Support › Safety Instructions & Warranty

Height

adjustment

Download Assembly

Instructions with Text

DTP410-Assembly instructions-Online-2401

For more information: barkanmounts.com

TV Size

13”-83”

33cm-211cm

If you are satisfied with the product, please give us a 5 stars  rating on the website you bought it from. If you

are not satisfied please contact us at https://www.barkanmounts.com/support and we will solve the problem for you.

TV Weight

50kg

110lbs

Safety instructions and installation warnings (provided separately)

must be read in full, prior to assembly.

92-120cm

36.2”-47.2”

Summary of content (15 pages)

PAGE 1
Page 1 Elegant Telescopic Tripod TV Mount Floor Stand Tilt Height adjustment 36.2”-47.2” 92-120cm Download Assembly Instructions with Text Warning! Ignoring the safety and assembly instructions may result in SERIOUS OR FATAL INJURIES from tip over or the falling of the product and the electrical appliances. Opening the package represents your undertaking to closely read and follow the instructions. This product is not intended for use in public places.
PAGE 2
Page 2 Warnings! Tip Over Hazard! Collision Hazard – place the product in a position that will prevent people from colliding with it Keep children under the age of 15 away from the product Anchor the product to the wall – using 2 strong cables Do not place the product on inclined surfaces, at the edge of a surface or near stairs Adjust the TV tilt angle carefully. Using excessive force might break the screen or tip over the product.
PAGE 3
Page 3 Main Parts C Plastic wing X2 S Swivel mechanism A P11 B Plastic cover G Upper pipe D TV plate Adaptor X4 Plastic wing X2 P10 Plastic cover X2 E Front leg E Front leg F Back leg
PAGE 4
Included Hardware Z6 Page 4 not to scale Z8 Z7 M6 x8 L mm Z1 4 20 Z2 6 Z3 4 6 25 𝟓 𝟖 1 4 Z4 8 25 1 4 Z5 8 45 1 M8 x4 x4 M6 x1 H3 H2 H1 M6 x2 T4 T3 T2 T1 x1 x2 x2 x2 x2 x2 Required Tools 𝟓 ” / 8mm 𝟏𝟔 𝟑 ” / 10mm 𝟖 No.
PAGE 5
Page 5 Connect the TV plate to the back of the TV Wrong Right Purchase longer screws Use the spacers (Z7) in order to adjust the screws length inside the TV Continue according to your TV mounting hole pattern 75 – 200mm 200 – 600mm 1 1b 1a 1a Page 5 75x75 mm up to 200X200 mm (inclusive) hole pattern Z4/Z5 T1 NO FORCE A Z1/Z2/Z3 Z6 T1 Z7 Optional
PAGE 6
1b 1 Page 6 Hole pattern above 200x200 mm up to 600x400 mm: Disassemble the screws B 2 Connect the 4 adaptors to the TV plate, and reassemble the screws Curved screen Flat screen A A P1 B T1 T1 P1 PARTIAL TIGHTENING Right Wrong B PARTIAL TIGHTENING Right Wrong
PAGE 7
Page 7 Position the adaptors according to your TV’s hole pattern Max. 600mm 300mm 200mm 300mm 300mm Max.
PAGE 8
3 Connect the front legs to the back leg, do not tight the 4 screws until all the screw are assembled. E E PARTIAL TIGHTENING F Back side 4 Tighten the 4 screws.
PAGE 9
5 Wrong 6 Page 9 Make sure that all 4 screws are fully tightened and there is no gap between the front legs and the back leg. Wrong Right 1. Place P11 on top of the back leg 2.
PAGE 10
7 Page 10 Pass the cables through the pipes 8 1 Adjust the stand to the desired height and connect the screws H3 CABLE MANAGEMENT H1 H2 𝟑 ” / 10mm 𝟖 2 9 Tighten the screws Assemble the plastic covers P10 P10
PAGE 11
Page 11 10 Place two nuts (Z8) in each of the two nut-housings (P2). 11 Attach the nut-housings (P2) on to part S. Make sure that the tab is inserted into the slot. S Z8 P2 P2 Make sure that the tab is inserted into the slot 12 Push parts P3 down on the nut-housings (P2). The upside down “T” must pass the protruding tooth (shown below). 13 Weight test Apply force on the upper part of the product to make sure everything is assembled properly.
PAGE 12
Page 12 14 Connect the TV plate with the TV to the upper pole Make sure that the TV plate slots are positioned properly on the 2 small beams 15 Insert and tighten the screws from both sides to create friction for the tilt mechanism. Adjust the TV tilt angle carefully.
PAGE 13
Page 13 16 Anchor the product to the wall Mark holes on the wall according to the desired position X2 CONNECTION POINTS Follow the steps according to your wall type 17 Make sure all holes are drilled inside the studs Drill with 𝟓 𝟏𝟔 ” \ 8mm drill bit 𝟓 ” 𝟏𝟔 \ 8mm 2.75” \ 70mm Use a Stud Finder 𝟏 Drill with ” \ 3mm drill bit 𝟖 2.75” \ 70mm 𝟏 ” 𝟖 \ 3mm T3
PAGE 14
Page 14 18 Connect the cables (T1) to the wall FULL TIGHTENING T2 T4 T1 19 Make sure the cables are tight. Adjust the lengths using a wrench.
PAGE 15
Page 15 20 Level the TV SCREEN LEVELING