Page 1 TV Wall Mount Full Motion: Rotate, Fold, Swivel & Tilt For more information: barkanmounts.com BM343LP-MAN-ONL-03_2007 If you are satisfied with the product, please give us a 5 stars rating on the website you bought it from. If you are not satisfied please contact us at https://www.barkanmounts.com/support and we will solve the problem for you. TV Size 13”-65” 33cm-165cm TV Weight US EU 80lbs 36kg CAUTION This Mount is intended for use only with the maximum weight indicated.
ATTENTION! Please read the following. EN WARNING! Disregarding the safety and assembly instructions may result in the falling of, and/ or damage to your electrical appliance. Opening the package represents your undertaking to closely read and follow the instructions. This mount is not intended for use in public places. For Safety Instructions, warranty and further information, go to: www.barkanmounts.
UPOZORNĚNÍ! Nedodržení bezpečnostních a montážních pokynů, může způsobit pád a následné poškození Vašeho elektronického přístroje. Po rozbalení, si pozorně přečtěte montážní návod a ve vlastním zájmu jej dodržte. Tento držák není určeno pro použití na veřejných místech. Pro bezpečnostní pokyny a pro více informací se podívejte na: www.barkanmounts.
EN Caution This mount is intended for use only with the maximum weight as indicated. Using heavier products might cause injury. ES Atención Este soporte debe ser utilizado solo con el máximo peso especificado. Utilizarlo con productos de mayor peso puede causar daños. FR Attention Utilisez ce support en ne depassant pas le poids maximum indiqué. L’utilisation de produits plus lourds pourrait causer des dégats.
EN Do not install on walls and ceilings made of: gypsum board, drywall, light processed blocks, silicate boards/bricks, a damp wall, weak or very old blocks or wooden panel! For installation on gypsum or light processed blocks please consult with an authorized installer or appropriate building specialist to install the product. ES No instalar en paredes o techos de yeso, silicate, bloques viejos, paredes húmedas, paredes débiles o paneles de madera.
Page 2 Included Parts A B Bracket x1 Z8 x4 x6 W2 W1 x2 x3 x3 Y1 Wall Plate W3 x4 Z7 Z4 Drilling Template Adaptor x1 x1 D C TV Plate L inch 6 16 5 Z2 6 25 Z3 4 20 Z5 8 25 1 4 Z6 8 45 13 4 4 M Z1 x1 3 Plastic Cover x1 Required Tools 7/16” 11 mm No.
Page 3 Connect the TV plate to the back of the TV Wrong Right Purchase longer screws Use the spacers (Z7) in order to adjust the screws length inside the TV Continue according to your TV mounting hole pattern 75 – 100mm 200 – 400mm 1 1b 1a 1a Page 4 75x75 mm up to 100x100 mm hole pattern Z5/Z6 NO FORCE B Z1/Z2/Z3 Z4 2 B Z7 Optional Page 5
1b Page 4 Hole pattern 200x200 mm – 400x400 mm: Disassemble the screws, connect the 4 Adaptors to the TV Plate and reassemble the screws. B C C PARTIAL TIGHTENING Position the Adaptors according to your TV’s hole pattern Max. 400mm 200mm 400mm TV 200mm 200mm Max.
Page 5 Install the Bracket on the Wall Measure the distance between the location of the TV’s mounting holes’ center (marked on the Drilling Template) and the bottom of the TV, in order to set the required height of the TV 5.3” / 13.4 cm 2 2.3” / 5.9cm D https://www.barkanmounts.
4a Make sure all holes are drilled inside the studs Page 6 4b First use 1/4” \ 6mm drill bit 1/4” \ 6mm 1 2.75” \ 70mm Afterwards use 3/8” \ 10mm drill bit 2 3/8” \ 10mm 2.75” \ 70mm Drill with 5/32” \ 4mm drill bit 5/32” \ 4mm 2.75” \ 70mm W2 3/8”/ 10 mm The anchor must be sunk at least 3/8"/10 mm into the plaster coating W3+W1 1 W3+W1 2 A 2 x 360° A 1 7/16”/ 11mm 7/16”/ 11mm 2 FULL TIGHTENING 4 x 360° FULL TIGHTENING
5 Page 7 Weight test Apply force on the upper part of the Bracket and make sure it is well connected 80Lbs/ 36Kg 6 Assemble the Wall Plate Plastic Covers 7 Place two nuts in the plastic nut-housings Y1 Z8 Y2 8 Connect the TV with the TV Plate to the Bracket Make sure that the TV Plate slots are positioned properly on 2 small beams (Bracket)
Page 8 9 In order to secure the TV, insert and tighten the screw from each side of the mount. Tighten the screws in order to create the necessary friction for the tool free Tilt mechanism.0 FALL PROOF Z4 10 Disconnect the Cable Management 11 TOUCH & TILT Z1/Z2 Place the TV cables in the Cable Management covers. CABLE MANAGEMENT 12 Reconnect the Cable Management covers to the mount.
Page 9