Page 1 Long TV Ceiling Mount Full Motion: Telescopic, Swivel & Tilt For more information: barkanmounts.com 4500L-MAN-ONL-03_2011 If you are satisfied with the product, please give us a 5 stars rating on the website you bought it from. If you are not satisfied please contact us at https://www.barkanmounts.com/support and we will solve the problem for you. TV Size 13”-75” 33cm-190cm CAUTION This Mount is intended for use only with the maximum weight indicated.
ATTENTION! Please read the following. EN WARNING! Disregarding the safety and assembly instructions may result in the falling of, and/ or damage to your electrical appliance. Opening the package represents your undertaking to closely read and follow the instructions. This mount is not intended for use in public places. For Safety Instructions, warranty and further information, go to: www.barkanmounts.
UPOZORNĚNÍ! Nedodržení bezpečnostních a montážních pokynů, může způsobit pád a následné poškození Vašeho elektronického přístroje. Po rozbalení, si pozorně přečtěte montážní návod a ve vlastním zájmu jej dodržte. Tento držák není určeno pro použití na veřejných místech. Pro bezpečnostní pokyny a pro více informací se podívejte na: www.barkanmounts.
EN Caution This mount is intended for use only with the maximum weight as indicated. Using heavier products might cause injury. ES Atención Este soporte debe ser utilizado solo con el máximo peso especificado. Utilizarlo con productos de mayor peso puede causar daños. FR Attention Utilisez ce support en ne depassant pas le poids maximum indiqué. L’utilisation de produits plus lourds pourrait causer des dégats.
EN Do not install on walls and ceilings made of: gypsum board, drywall, light processed blocks, silicate boards/bricks, a damp wall, weak or very old blocks or wooden panel! For installation on gypsum or light processed blocks please consult with an authorized installer or appropriate building specialist to install the product. ES No instalar en paredes o techos de yeso, silicate, bloques viejos, paredes húmedas, paredes débiles o paneles de madera.
Page 2 Included Parts not to scale A1 C1 B1 C2 A2 A2 x1 D x1 Ceiling plate E Plastic cover x1 F x1 G TV plate Adapters x4 x1 Z4 Z7 Y2 Y1 x4 x4 W1 x1 x8 x4 x4 L mm inch 6 16 5 Z2 4 20 3 Z3 8 45 13 4 4 Z5 6 25 1 4 Z6 8 25 1 4 M Z1 x8 W3 W2 x4 Required Tools 13/32” 10 mm 1/4” 6 mm 7/16” 11 mm 5/32” 4 mm No.
Page 3 Connect the TV plate to the back of the TV Wrong Right Purchase longer screws Use the spacers (Z7) in order to adjust the screws length inside the TV Continue according to your TV mounting hole pattern 75 – 200mm 200 – 600mm 1 1b 1a 1a Page 4 75x75 mm – 200X200 mm hole pattern Z3/Z6 NO FORCE F Z1/Z5 Z4 2 Z7 Optional Page 5
1b Page 4 Hole pattern above 200x200 mm and up to 600x400 mm: Disassemble the screws, connect the 4 Adaptors to the TV Plate and reassemble the screws. PARTIAL TIGHTENING F G G Position the Adaptors according to your TV’s hole pattern Max. 600mm 300mm 600mm 200mm 300mm 300mm Max.
Page 5 Follow the steps according to your ceiling type 2a 3a 2b Make sure all holes are drilled inside the joist/ stud 3b Make sure there are no electrical/water lines in the ceiling before drilling and then drill according to the markings Mark the holes on the ceiling according to the required position 4b 4a UP D Use a Stud Finder UP D 5a Page 6 5b Page 6
5a Drill with 5/32” \ 4mm drill bit Page 6 5b 1 First use 1/4” \ 6mm drill bit 2.75” \ 70mm 2.75” \ 70mm 1/4” \ 6mm 5/32” \ 4mm 2 Afterwards use 3/8” \ 10mm drill bit 3/8” \ 10mm 2.75” \ 70mm 3/8”/ 10 mm W2 The anchor must be sunk at least 3/8"/10 mm into the plaster coating D 1 D W1+W3 7/16”/ 11mm 2 2 x 360° 7/16”/ 11mm W1+W3 1 A1 A1 2 4 x 360° FULL TIGHTENING FULL TIGHTENING
6 Page 7 Weight test Apply force on the upper pipe and make sure it is well connected 95Lbs/ 43Kg 7 Assemble the ceiling plate plastic cover E A1 8 Assemble the mount according to the desired height of the television 17” – 39” 43cm – 99cm 41” – 63” 105cm – 160cm 8a Page 8 8b Page 9
Page 8 8a 17” – 39” 43cm – 99cm Assembly 1 Slide the shorter pipe (C2) out of the longer pipe(C1) C1 2 C2 Assemble the mount at the desired length Y1 Y2 A1 A2 5.
8b Page 9 41” – 63” 105cm – 160cm Assembly 1 Slide the shorter pipe (C2) out of the longer pipe(C1) A1 C1 Y1 Y2 2 C2 C2 Assemble the mount at the desired length A2 C2 Length options B1 13/32” / 10mm 5.
9 10 Place the TV cables in the Cable Management Page 10 Connect the TV Plate with the TV Make sure that the TV Plate slots are positioned properly on the 2 small bent parts
Page 11 11 In order to secure the TV and to adjust friction, insert and tighten 2 screws on each side of the mount.
Page 12