Page 1 TV Wall Mount Tilt For more information: barkanmounts.com E314-MAN-ONL-01_2020 If you are satisfied with the product, please give us a 5 stars rating on the website you bought it from. If you are not satisfied please contact us at https://www.barkanmounts.com/support and we will solve the problem for you. TV Size 13”-58” 33cm-147cm TV Weight US EU 55lbs 25kg CAUTION This Mount is intended for use only with the maximum weight indicated. Using heavier products might cause injury.
ATTENTION! Please read the following. EN WARNING! Disregarding the safety and assembly instructions may result in the falling of and/ or damage to your electrical appliance. Opening the package represents your undertaking to closely read and follow the instructions. This mount is not intended for use in public places. For Safety Instructions, warranty and further information, go to: www.barkanmounts.
SR UPOZORNĚNÍ! Nedodržení bezpečnostních a montážních pokynů, může způsobit pád a následné poškození Vašeho elektronického přístroje. Po rozbalení, si pozorně přečtěte montážní návod a ve vlastním zájmu jej dodržte. Tento držák není určeno pro použití na veřejných místech. Pro bezpečnostní pokyny a pro více informací se podívejte na: www.barkanmounts.
EN ES ! RU Caution - This mount is intended for use only with the maximum weight as indicated. Using heavier products might cause injury. Atención DA Attention EL Este soporte debe ser utilizado solo con el máximo peso especificado. Utilizarlo con productos de mayor peso puede causar daños. FR Utilisez ce support en ne depassant pas le poids maximum indiqué. L’utilisation de produits plus lourds pourrait causer des dégats.
! Do not install on walls and ceilings made of: gypsum board, drywall, light processed blocks, silicate boards/bricks, a damp wall, weak or very old blocks or wooden panel! For installation on gypsum or light processed blocks please consult with an authorized installer or appropriate building specialist to install the product.
Page 2 Included Parts not to scale A B Vertical Rail Wall Rail Z2 Z1 x1 Z6 Vertical Rail x1 x1 x1 D Rubber Sticker C x2 x2 L L mm inch # M Z3 4 14 9 Z4 6 20 3 Z5 8 25 Z7 x4 x6 Required Tools 3/8” 10 mm 1/4” 6 mm 7/16” 11 mm 5/32” 4 mm 3/8” 10 mm pcs 16 4 4 4 1 4
Page 3 Connect the TV plate to the back of the TV Wrong Right Purchase longer screws Use the spacers (Z6) in order to adjust the screws length inside the TV Make sure that the tilt mechanism is loose OPEN 1 75x75 mm up to 400x400 mm hole pattern Z5 NO FORCE Z3/Z4 C Z7 B Z6 Optional
Page 4 Install the Bracket on the Wall 2 5.7” / 22 cm Measure the distance between the location of the TV’s upper mounting holes’ center and the bottom of the TV, in order to set the required height of the TV https://www.barkanmounts.
4a Make sure all holes are inside the studs 4b Page 5 First use 1/4” \ 6mm drill bit 1/4” \ 6mm 1 2.75” \ 70mm Afterwards use 3/8” \ 10mm drill bit 2 3/8” \ 10mm 2.75” \ 70mm Drill with 5/32” \ 4mm drill bit 5/32” \ 4mm 2.75” \ 70mm Z2 3/8”/ 10 mm The anchor must be sunk at least 3/8"/10 mm into the plaster coating 1 2 Z1+Z7 7/16”/ 11mm 2 x 360° A 7/16”/ 11mm 1 A Z1+Z7 2 FULL TIGHTENING 4 x 360° FULL TIGHTENING
Page 6 5 6 Weight test Apply force on the upper part of the Wall Rail and make sure it is well connected Paste the rubber sticker below the Bracket D 55Lbs/ 25Kg 7 Connect the TV with the Vertical Rails to the Wall Rail Make sure that the Vertical Rails are positioned properly on the Wall Rail 1 2 8 Adjust the tilt and tighten tilt screws 3/8” / 10mm TILT CLOSE