Page 1 White Extra Long Dual Arm TV Wall Mount Black Tilt Swivel Download Assembly Instructions with Text For more information: barkanmounts.com If you are satisfied with the product, please give us a 5 stars rating on the website you bought it from. If you are not satisfied please contact us at https://www.barkanmounts.com/support and we will solve the problem for you.
Included Parts A Page 2 not to scale B Bracket C Front Arms x2 Y6 Cable Holder Y7 Cable Holder Z7 Z6 x4 P2 Nut-housing P3 Nut-housing W3 x8 x8 P1 x6 x4 S1 Silicone Pad x2 x1 Z1-Z5 Cover x2 x1 x8 Z8 x8 x1 W2 W1 x2 x2 x4 x1 x2 Drilling Template Y4 Wall Plate Cover Y5 Wall Plate Cover Y3 Y2 Y1 E Adaptor x1 x1 x1 D TV Plate x6 x4 L L mm inch 4 20 4 Z2 6 16 13ൗ 16 5ൗ 8 Z3 6 25 1 4 Z4 8 25 1 4 Z5 8 45 113ൗ16 4 # M Z1 Required Tools 7/16
Connect the TV plate to the back of the TV. Page 3 Wrong Right Purchase longer screws. 1 Use the spacers (Z7) in order to adjust the screws length inside the TV. 75 – 200mm 200 – 400mm Continue according to your TV mounting hole pattern. 1b 1a 1a 75x75 mm – 200x200 mm (inclusive) hole pattern. Connect the TV Plate (C) to the TV in all 4 connection holes.
1b A Page 4 Hole pattern above 200x200 mm up to 600x400 mm: Disassemble the screws.
Page 5 Position the adaptors (D) according to your TV back screen mounting holes . C 300mm Max. 600mm 400mm 200mm 300mm 300mm Max. 400mm 600mm For more positioning options turn to the last page. D Connect the TV Plate (C) with the adaptors (D) to the TV in all 4 connection holes. Z4/Z5 FULL TIGHTENING NO FORCE Z1/Z2/Z3 Z6 C Z7 Optional D 2 Optional – Corner installation Functionality may vary depending on the distance from the corner. A A Max.
2 Page 6 Determine the desired installation height Note, the center of the TV back screen mounting holes is usually different from the center of the entire screen. 2a The recommended height of the screen center from the floor is 43” – 47” / 110 - 120 cm. Determine the distance from the bottom edge of the TV to the floor. 2b Determine the distancefrom the center of the back screen mounting holes to the bottom edge of the TV.
Page 7 3 Follow the steps according to your wall type 3b 3a Be careful not to drill into water pipes or electricity lines Make sure all holes are drilled inside the studs Mark the holes on the wall according to the required height 4 X8 X6 CONNECTION POINTS CONNECTION POINTS Use a stud finder E 4a E 4b
4a Drill with 5/32” \ 4mm drill bit. 4b First use 1/4” \ 6mm drill bit. 1/4” \ 6mm 1 Page 8 5/32” \ 4mm 2.75” \ 70mm Then use 3/8” \ 10mm drill bit. 2.75” \ 70mm 3/8” \ 10mm 2 2.75” \ 70mm Place the Bracket’s wall plate (A) on the wall, insert the screws and tighten them W2 3/8”/ 10 mm The anchor must be sunk at least 3/8“ \ 10 mm into the plaster coating 16" W1+W3 A W1+W3 1 A 2 2 x 360° 1 7/16”/ 11mm 7/16”/ 11mm 2 FULL TIGHTENING 4 x 360° FULL TIGHTENING
5 Page 9 6 Paste the 6 silicone pads (S1) on the plastic covers. (Y4,Y5) Assemble the wall plate covers.(y4,Y5) S1 Y4 Y5 Y4 7 Y5 Connect the front arms (B) to the rear arms of the bracket (A). Y3 Y1 FULL TIGHTENING Y2 A 8 Weight test B 9 Place two nuts (Z8) in the nut-housing (P2). Apply force on the upper part of the arms and make sure it is well connected.
Page 10 Assemble the nut-housing (P2) make sure that the tab is inserted into the slot. B P2 Make sure that the tab is inserted into the slot 11 Assemble the nut-housing cover (P3) on the nut-housings (P2). Push the nut-housing cover P3 down until it snaps into place, and the holes are aligned. P2 12 P3 Connect the TV with the TV plate (C) to the bracket at the edge of the arms (B).
Page 11 13 Insert and tighten the screws from both sides to create friction for the tilt mechanism. Adjust the TV tilt angle carefully. Z6 14 Z2/Z3 Place the TV cables in the cable holders (Y6,Y7) and attach them to the arms. Y6 Y7 CABLE MANAGEMENT 15 Level the TV.
Move the TV by pulling/pushing the Bracket (A). To disconnect the TV: Be careful when you move the TV by the screen.