Page 1 Extra Long Dual Arm TV Wall Mount Full Motion: Rotate, Fold, Swivel & Tilt For more information: barkanmounts.com BM464XLW-MAN-ONL-01_2101 If you are satisfied with the product, please give us a 5 stars rating on the website you bought it from. If you are not satisfied please contact us at https://www.barkanmounts.com/support and we will solve the problem for you.
ATTENTION! Please read the following. EN WARNING! Disregarding the safety and assembly instructions may result in the falling of, and/ or damage to your electrical appliance. Opening the package represents your undertaking to closely read and follow the instructions. This mount is not intended for use in public places. For Safety Instructions, warranty and further information, go to: www.barkanmounts.
UPOZORNĚNÍ! Nedodržení bezpečnostních a montážních pokynů, může způsobit pád a následné poškození Vašeho elektronického přístroje. Po rozbalení, si pozorně přečtěte montážní návod a ve vlastním zájmu jej dodržte. Tento držák není určeno pro použití na veřejných místech. Pro bezpečnostní pokyny a pro více informací se podívejte na: www.barkanmounts.
EN Caution This mount is intended for use only with the maximum weight as indicated. Using heavier products might cause injury. ES Atención Este soporte debe ser utilizado solo con el máximo peso especificado. Utilizarlo con productos de mayor peso puede causar daños. FR Attention Utilisez ce support en ne depassant pas le poids maximum indiqué. L’utilisation de produits plus lourds pourrait causer des dégats.
EN Do not install on walls and ceilings made of: gypsum board, drywall, light processed blocks, silicate boards/bricks, a damp wall, weak or very old blocks or wooden panel! For installation on gypsum or light processed blocks please consult with an authorized installer or appropriate building specialist to install the product. ES No instalar en paredes o techos de yeso, silicate, bloques viejos, paredes húmedas, paredes débiles o paneles de madera.
Included Parts A B Bracket C Front Arms Z7 x4 W3 Drilling Template x4 x1 W2 W1 Sticker x6 x8 x8 Y4 Wall Plate Y3 Y2 Y1 E Adaptor x1 Z8 x8 D TV Plate x1 x1 Z4 Page 2 not to scale Plastic Cover x8 Y5 Wall Plate Plastic Cover x2 Y6 Cable Management x1 x2 Y7 x1 x1 x2 Cable Management L L mm inch 6 16 5 Z2 6 25 Z3 4 20 Z5 8 25 1 4 Z6 8 45 13 4 4 # M Z1 x2 Required Tools 7/16” 11 mm No.
Page 3 Connect the TV plate to the back of the TV Wrong Right Purchase longer screws Use the spacers (Z7) in order to adjust the screws length inside the TV Continue according to your TV mounting hole pattern 75 – 200mm 200 – 600mm 1 1b Page 4 1a 1a 75x75 mm up to 200X200 mm hole pattern Z5/Z6 NO FORCE C Z1/Z2/Z3 Z4 2 Z7 Optional Page 5
1b Page 4 Hole pattern above 200x200 mm up to 600x400 mm: Disassemble the screws, connect the 4 Adaptors to the TV Plate and reassemble the screws. PARTIAL TIGHTENING C D D Position the Adaptors according to your TV’s hole pattern Max. 600mm 300mm 200mm 300mm 300mm Max.
Page 5 Optional – Corner installation Functionality may vary according to the wall construction A 3 A Page 6 Regular flat wall installation - Install the Bracket on the Wall 2 5.9” / 14.9 cm E 119cm 8” / 20.3 cm https://www.barkanmounts.
Follow the steps according to your wall type 3a 4a Page 6 3b Make sure all holes are drilled inside the studs 4b Mark the holes on the wall according to the required height X6 X8 CONNECTION POINTS Use a Stud Finder E 5a Page 7 CONNECTION POINTS E 5b Page 7
5a Page 7 5b Drill with 5/32” \ 4mm drill bit First use 1/4” \ 6mm drill bit 1/4” \ 6mm 1 5/32” \ 4mm 2.75” \ 70mm Afterwards use 3/8” \ 10mm drill bit 3/8” \ 10mm 2 2.75” \ 70mm 2.75” \ 70mm W2 A 3/8”/ 10 mm W1+W3 The anchor must be sunk at least 3/8"/10 mm into the plaster coating 1 W1+W3 2 2 x 360° 7/16”/ 11mm 1 A FULL TIGHTENING 7/16”/ 11mm 2 4 x 360° FULL TIGHTENING
6 Paste the 6 stickers on the Plastic Covers Page 8 Assemble the Wall Plate Plastic Covers 7 Z8 Y5 Z8 Y4 8 Connect the Front Arms (B) to the Bracket (A) 9 Weight test Apply force on the upper part of the Bracket and make sure it is well connected Y3 Y1 FULL TIGHTENING Y2 B 110Lbs/ 50Kg A 10 Place the Bracket upright and connect the TV Plate with the TV to the Front Arms Make sure that the TV Plate slots are positioned properly on 2 small beams (Front Arms)
Page 9 11 In order to secure the TV, insert and tighten 2 screws on each side of the mount. Tighten the screws in order to create the necessary friction for the tool free Tilt mechanism.
Page 10