Page 1 TV Wall Mount Full Motion: Rotate, Fold, Swivel & Tilt For more information: barkanmounts.com BM464-MAN-ONL-03_1909 If you are satisfied with the product, please give us a 5 stars rating on the website you bought it from. If you are not satisfied please contact us at https://www.barkanmounts.com/support and we will solve the problem for you. TV Size 13”-90” 33cm-229cm TV Weight US EU 132lbs 60kg CAUTION This Mount is intended for use only with the maximum weight indicated.
ATTENTION! Please read the following. EN WARNING! Disregarding the safety and assembly instructions may result in the falling of and/ or damage to your electrical appliance. Opening the package represents your undertaking to closely read and follow the instructions. This mount is not intended for use in public places. For Safety Instructions, warranty and further information, go to: www.barkanmounts.
SR UPOZORNĚNÍ! Nedodržení bezpečnostních a montážních pokynů, může způsobit pád a následné poškození Vašeho elektronického přístroje. Po rozbalení, si pozorně přečtěte montážní návod a ve vlastním zájmu jej dodržte. Tento držák není určeno pro použití na veřejných místech. Pro bezpečnostní pokyny a pro více informací se podívejte na: www.barkanmounts.
ES ! RU Caution - This mount is intended for use only with the maximum weight as indicated. Using heavier products might cause injury. Atención DA Attention EL Este soporte debe ser utilizado solo con el máximo peso especificado. Utilizarlo con productos de mayor peso puede causar daños. FR Utilisez ce support en ne depassant pas le poids maximum indiqué. L’utilisation de produits plus lourds pourrait causer des dégats.
EN ! Do not install on walls and ceilings made of: gypsum board, drywall, light processed blocks, silicate boards/bricks, a damp wall, weak or very old blocks or wooden panel! For installation on gypsum or light processed blocks please consult with an authorized installer or appropriate building specialist to install the product.
Included Parts A B Bracket x2 G x1 Z4 Drilling Template Y2 1 Z1 6 25 Z2 4 20 3 Z3 8 45 13 4 4 Z5 6 16 5 4 Z6 8 25 D 4 4 4 8 4 1 F TV Plate Adaptor x1 x4 Z9 x1 x4 x6 pcs Z8 W2 x2 inch x1 x8 W1 Z10 mm Page 2 M Z7 x1 L # C Connector Front Arms L x2 Y1 W3 x6 x2 x6 Y4 Y3 x2 x2 x2 Required Tools 1/2” 13 mm No.
Page 3 Connect the TV plate to the back of the TV Wrong Right Purchase longer screws Continue according to your TV mounting hole pattern 75 – 200mm 200 – 600mm 1 1a 1a Use the spacers (Z7) in order to adjust the screws length inside the TV 1b Page 4 75x75 mm – 200X200 mm hole pattern Z3/Z6 NO FORCE D Z1/Z2 Z4 2 Z7 Optional Page 5
1b Page 4 Hole pattern above 200x200 mm and up to 600x400 mm Disassemble the screws, connect the 4 Adaptors to the TV Plate and reassemble the screws. PARTIAL TIGHTENING D F F Position the Adaptors according to your TV’s hole pattern Max. 600mm 300mm 200mm 300mm 300mm Max.
Page 5 Regular flat wall installation 2 Connect the Connector )C) to the Bracket (A) Make sure that the tab is inserted into the slot A C FULL TIGHTENING 3 Page 6 Optional – Corner installation Functionality may vary according to the wall construction Max. TV Size 55”\139cm A A 4 Page 7
Page 6 Install the Bracket on the Wall Measure the distance between the location of the TV’s mounting holes’ center (marked on the Drilling Template) and the bottom of the TV, in order to set the required height of the TV G 5.7” / 14.5 cm 3 7.9” / 20.1 cm https://www.barkanmounts.
4a Page 7 Follow the steps according to your wall type 4 Make sure all holes are inside the studs 4b Mark the holes on the wall according to the required height Use a Stud Finder G G
5a Page 8 5b First use 1/4” \ 6mm drill bit Drill with 5/32” \ 4mm drill bit 1/4” \ 6mm 1 5/32” \ 4mm 2.75” \ 70mm Afterwards use 3/8” \ 10mm drill bit 2.75” \ 70mm 3/8” \ 10mm 2 2.75” \ 70mm W2 3/8”/ 10 mm W1+W3 The anchor must be sunk up to 3/8"/10 mm into the plaster coating 1 W1+W3 2 ½”/ 13mm 2 x 360° 1 FULL TIGHTENING ½”/ 13mm 2 4 x 360° FULL TIGHTENING
Assemble the Plastic Covers 6 7 Assemble the Plastic Covers Page 9 Y4 Y4 Y1 Y3 Connect the Front Arms to the Wall Plate 8 9 Weight test Apply force on the upper part of the Bracket and make sure it is well connected Z8 Z10 FULL TIGHTENING Z9 132Lbs/ 60Kg 10 Place the Bracket upright and connect the TV Plate with the TV to the Front Arms Make sure that the slot of the TV Plate is sitting properly on the pin of the Bracket
Page 10 11 Insert and lock the two screws on each side of the mount, to secure the TV. Adjust the friction of the tilt with a screwdriver.