ST-150B User guide K5903075/01AD 16/01/2014
Barco nv President Kennedypark 35, 8500 Kortrijk, Belgium Phone: +32 56.23.32.11 Fax: +32 56.26.22.62 Support: www.barco.com/esupport Visit us at the web: www.barco.
Table of contents TABLE OF CONTENTS 1. Welcome! .......................................................................................... 3 1.1 1.2 About the product .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. . 3 What’s in the box. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. . 3 2. Parts, controls and connectors .....
Table of contents 2 K5903075 ST-150B 16/01/2014
1. Welcome! 1. WELCOME! 1.1 About the product Smart Terminal The ST-150B is a multimedia Intel® Atom processor-based computer that is designed to serve as a Point of Care (POC) and Point of Information terminal (POI) within healthcare applications. It is a PC based system with 15" color TFT LCD display, Gigabit Ethernet, multi-COM port and USB 2.0 interfaces and High Definition Audio codec. The ST-150B Smart Terminal™ is as compact and user-friendly as a notebook computer.
1.
2. Parts, controls and connectors 2. PARTS, CONTROLS AND CONNECTORS 2.1 System setup Become familiar Before you set up the ST-150B, take a moment to become familiar with the locations and purposes of the controls, drives, connections and ports, which are illustrated in the figures below. Front When you place the ST-150B upright on the desktop, its front panel appears as shown in the figure below.
2. Parts, controls and connectors Left, Right When you look at the left side of the ST-150B, you will see a handset, fitted to the left docking port. At the right side of the terminal, you will see an MSR reader, fitted to the right docking port. 1 2 Image 2-2 Side views of the ST-150B 1 Handset (optional) 2 MSR Reader (Mag Stripe Reader) (optional) Bottom On the bottom side of the ST-150B you will find a Smart Card Reader and an I/O area, as shown in the figure below.
2. Parts, controls and connectors Rear On the rear of the ST-150B you will find the two removable access doors located left and right of the terminal. The right-hand cover provides access to the system DDR memory and a mini PCIe slot, and the left-hand cover provides access to the HDD, as shown in the figure below.
2. Parts, controls and connectors IO areas There are two I/O areas in the ST-150B; one is at the back and the other one is at the bottom. The figures below indicate the various ports of these two areas.
2.
2.
3. System installation 3. SYSTEM INSTALLATION 3.1 Mounting Fixing the terminal to a mounting solution The terminal is foreseen from a mounting anchor that can be used for different mounting solutions (arms, desk stands, ...). To install the terminal, please follow the detailed mounting instructions in the user guide, which is delivered with the mounting solution you have chosen for your terminal. 3.2 Installation Connecting the power cable Always handle the power cable by holding the plug end only.
3. System installation Image 3-3 Switching on the power 3.3 Installation of HDD, SSD (optional) CAUTION: The installation of the optional HDD and/or SSD drive should be carried out by a professional technician. Only UL-certified hard disks may be installed! Please contact a service technician or your reseller if you need this service. 3.4 Running the BIOS setup program BIOS setup Your ST-150B is likely to have been properly set up and configured by your dealer prior to delivery.
3. System installation 3.6 Installing the drivers Drivers After installing the system software, you will be able to install the necessary drivers. All the ST-150B drivers and updates can be obtained from Barco. The drivers and utilities used for the ST-150B are subject to change without notice. If in doubt, check with your local Barco office or contact our application engineers for the latest information regarding drivers and utilities.
3.
4. System operation 4. SYSTEM OPERATION 4.1 Frequently used functions Using the Smart Card Reader (SCR) 1. Insert the card firmly into the allocated slot with the chip facing towards the front of the terminal. (See figure below). The Smart Card will be recognized by the terminal. Image 4-1 Using the Smart Card Reader (SCR) Using the RFID Reader 1. Present the card to the reader by tapping and holding it briefly onto the clearly reader-marked area until the card is read.
4.
5. Maintenance 5. MAINTENANCE This device does not require any scheduled maintenance activities. In case of a defect, return the device to a Barco approved maintenance organization. In any case of doubts, contact the Barco Healthcare Division 5.1 Cleaning instructions Cleaning is no mandatory maintenance activity for the ST-150B. During normal use, the ST-150B surfaces may become soiled. If you should like to clean them, follow the detailed cleaning instructions in the below paragraph.
5.
6. Important information 6. IMPORTANT INFORMATION 6.1 Safety information General recommendations Read the safety and operating instructions before operating the device. Retain safety and operating instructions for future reference. Adhere to all warnings on the device and in the operating instructions manual. Follow all instructions for operation and use. Electrical Shock or Fire Hazard To prevent electric shock or fire hazard, do not remove cover. No serviceable parts inside.
6. Important information • • • • • • • • • • • • Warning: if the equipment is not used for a long time, please make sure that the battery is removed from the equipment. Place the terminal on a stable surface that can support the weight of at least 4 terminals or hang from a reliable structure during installation. Dropping the equipment is likely to cause serious injury to a child or adult, and serious damage to the equipment.
6. Important information Transient over-voltage If the device is not used for a long time, disconnect it from the AC inlet to avoid damage by transient over-voltage. To fully disengage the power to the device, please disconnect the power cord from the AC inlet. Power cords: • • • • • Utilize a UL-listed detachable power cord, 3-wire, type SJ or equivalent, 18 AWG min., rated 250 V min., provided with a hospital-grade type plug 5-15P configuration for 120V application, or 6-15P for 240V application.
6. Important information By participating in separate collection of batteries, you will help to ensure proper disposal and to prevent potential negative effects on the environment and human health. Turkey RoHS compliance Türkiye Cumhuriyeti: AEEE Yönetmeliğine Uygundur.
6. Important information 在中国大陆销售的相应电子信息产品（EIP）都必须遵照中国大陆《电子信息产品污染控制标识要求》标准 贴上环保使用期限（EFUP）标签。Barco产品所采用的EFUP标签（请参阅实例，徽标内部的编号使用于制 定产品）基于中国大陆的《电子信息产品环保使用期限通则》标准。 All Electronic Information Products (EIP) that are sold within Chinese Mainland must comply with the “Electronic Information Products Pollution Control Labeling Standard” of Chinese Mainland, marked with the Environmental Friendly Use Period (EFUP) logo.
6. Important information With the installation of the device, use only the delivered power supply or a spare part provided by the legal manufacturer. Using another can result in a decrease of the immunity level of the device. Electromagnetic emissions The ST-150B is intended for use in the electromagnetic environment specified below. The customer or the user of the ST-150B should assure that it is used in such an environment.
6. Important information Immunity test Electromagnetic environment – Test levels guidance Mains power quality Surge ± 1 kV line(s) to line(s) ± 1 kV line(s) to line(s) should be that of a typical IEC61000-4-5 ± 2 kV line(s) to earth ± 2 kV line(s) to earth commercial or hospital environment Voltage dips, short < 5% U T 1(> 95% dip in < 5% U T (> 95% dip in Mains power quality interruptions and voltage U T) for 0.5 cycle should by that of a typical U T) for 0.
6. Important information Immunity test IEC 60601 Compliance level Test levels Electromagnetic environment – guidance electromagnetic site survey,2 should be less than the compliance level in each frequency range.3 Interference may occur in the vicinity of equipment marked with symbol: At 80 MHz and 800 MHz, the higher frequency range applies. These guidelines may not apply in all situations. Electromagnetic propagation is affected by absorption and reflection from structures, objects and people.
6. Important information These guidelines may not apply in all situations. Electromagnetic propagation is affected by absorption and reflection form structures, object and people. 6.5 Explanation of symbols Symbols on the device On the device or power supply, you may find the following symbols (nonrestrictive list): Indicates the device meets the requirements of the applicable EC directives.
6.
6. Important information yy % 85 Indicates the range6 of humidity to which the device can be safely exposed when being stored. yyy kPa 106 Indicates the range6of atmospheric pressure to which the device can be safely exposed when being stored. 5x % xx kPa 50 6.6 Legal disclaimer Disclaimer notice Although every attempt has been made to achieve technical accuracy in this document, we assume no responsibility for errors that may be found.
6. Important information System memory DDR3 1066 2 or 4 GB Operating system Linux Windows® XP Embedded Windows® XP Professional for Embedded Systems Windows® 7 Embedded Connectivity LAN (x1) USB 2.
6.
