BARCO PROJECTION SYSTEMS BARCO PROJECTION SYSTEMS VISION 701 MULTIMEDIA VISION 701 MULTIMEDIA R9000740 R9000740 INSTALLATION MANUAL INSTALLATION MANUAL Date: 070597 Rev. : 01 Art. No. R5975248 Date: 070597 Rev. : 01 Art. No.
Due to constant research, the information in this manual is subject to change without notice. Due to constant research, the information in this manual is subject to change without notice. Produced by BARCO NV, May 1997. All rights reserved. Produced by BARCO NV, May 1997. All rights reserved. Trademarks are the rights of their respective owners. Trademarks are the rights of their respective owners.
WARNINGS ......................................................................................................... 1-1 SAFETY INSTRUCTIONS .................................................................................... 1-1 On safety ....................................................................................................... 1-4 On installation ............................................................................................... 1-5 On servicing .....................................
TABLE OF CONTENTS TABLE OF CONTENTS TABLE OF CONTENTS i-II TABLE OF CONTENTS 5975248 BARCOVISION 701 MULTIMEDIA 070597 i-II 5975248 BARCOVISION 701 MULTIMEDIA 070597
SAFETY INSTRUCTIONS WARNINGS WARNINGS SAFETY INSTRUCTIONS SAFETY INSTRUCTIONS on safety on installation on installation on servicing on servicing on cleaning on repacking on illumination 5975248 BARCOVISION 701 MULTIMEDIA 090497 SAFETY INSTRUCTIONS on safety 1-1 on cleaning on repacking on illumination 5975248 BARCOVISION 701 MULTIMEDIA 090497 SAFETY INSTRUCTIONS SAFETY INSTRUCTIONS 1-1
SAFETY INSTRUCTIONS SAFETY INSTRUCTIONS Notice on Safety Notice on Safety This equipment is built in accordance with the requirements of the international safety standards EN60950, UL 1950 and CSA C22.2 No.950, which are the safety standards of information technology equipment including electrical business equipment. This equipment is built in accordance with the requirements of the international safety standards EN60950, UL 1950 and CSA C22.2 No.
SAFETY INSTRUCTIONS SAFETY INSTRUCTIONS The lightning flash with an arrowhead within a triangle is intended to tell the user that parts inside this product may cause a risk of electrical shock to persons. The lightning flash with an arrowhead within a triangle is intended to tell the user that parts inside this product may cause a risk of electrical shock to persons.
SAFETY INSTRUCTIONS SAFETY INSTRUCTIONS * All the safety and operating instructions should be read before using this unit. * All the safety and operating instructions should be read before using this unit. * The safety and operating instructions manual should be retained for future reference. * The safety and operating instructions manual should be retained for future reference. * All warnings on the projector and in the documentation manuals should be adhered to.
SAFETY INSTRUCTIONS SAFETY INSTRUCTIONS B. Power cord with ANSI 73.11 plug: B. Power cord with ANSI 73.11 plug: The wires of the power cord are colored in accordance with the following code. The wires of the power cord are colored in accordance with the following code. Green/yellow: ground White: neutral Black: line (live) 3. Do not allow anything to rest on the power cord. Do not locate this product where persons will walk on the cord. To disconnect the cord, pull it out by the plug.
SAFETY INSTRUCTIONS SAFETY INSTRUCTIONS This product should never be placed near or over a radiator or heat register. This projector should not be placed in a built-in installation or enclosure unless proper ventillation is provided. On servicing On servicing Do not attempt to service this equipment yourself, as opening or removing covers may expose you to dangerous voltage potentials and risk of electric shock! Refer all sevicing to qualified service personnel.
SAFETY INSTRUCTIONS SAFETY INSTRUCTIONS - To ensure the highest optical performance and resolution, the projection lenses are specially treated with an anti-reflective coating, therefore, avoid touching the lens. To remove dust on the lens, use a soft dry cloth. Do not use a damp cloth, detergent solution, or thinner. On repacking On repacking Save the original shipping carton and packing material; they will come in handy if you ever have to ship your equipment.
SAFETY INSTRUCTIONS SAFETY INSTRUCTIONS SAFETY INSTRUCTIONS SAFETY INSTRUCTIONS 1-8 5975248 BARCOVISION 701 MULTIMEDIA 090497 1-8 5975248 BARCOVISION 701 MULTIMEDIA 090497
UNPACKING AND DIMENSIONS UNPACKING AND DIMENSIONS UNPACKING 5975248 BARCOVISION 701 MULTIMEDIA 090797 2-1 DIMENSIONS 5975248 BARCOVISION 701 MULTIMEDIA 090797 UNPACKING AND DIMENSIONS UNPACKING AND DIMENSIONS DIMENSIONS UNPACKING 2-1
UNPACKING AND DIMENSIONS UNPACKING AND DIMENSIONS Unpacking To open de banding, pull on the clip as shown in the first drawing. To open de banding, pull on the clip as shown in the first drawing. Take the projector out of its shipping carton and place it on a table. Save the original shipping carton and packing material, they will come in handy if you ever have to ship your projector. For maximum protection, repack your projector as it was originally packed at the factory.
UNPACKING AND DIMENSIONS UNPACKING AND DIMENSIONS UNPACKING AND DIMENSIONS Projector dimensions UNPACKING AND DIMENSIONS Projector dimensions 5975248 BARCOVISION 701 MULTIMEDIA 090797 2-3 5975248 BARCOVISION 701 MULTIMEDIA 090797 2-3
UNPACKING AND DIMENSIONS UNPACKING AND DIMENSIONS UNPACKING AND DIMENSIONS 2-4 UNPACKING AND DIMENSIONS 5975248 BARCOVISION 701 MULTIMEDIA 090797 2-4 5975248 BARCOVISION 701 MULTIMEDIA 090797
INSTALLATION GUIDELINES INSTALLATION GUIDELINES INSTALLATION GUIDELINES Environment What about ambient light? What about ambient light? Which screen type? Which screen type? What image size? How big should the image be? What image size? How big should the image be? Where to install the projector? How to install the projector? 5975248 BARCOVISION 701 MULTIMEDIA 090797 INSTALLATION GUIDELINES Environment 3-1 Where to install the projector? How to install the projector? 5975248 BARCOVISION 701 M
INSTALLATION GUIDELINES INSTALLATION GUIDELINES Installation guidelines Installation guidelines Careful consideration of things such as image size, ambient light level, projector placement and type of screen to use are critical to the optimum use of the projection system. Careful consideration of things such as image size, ambient light level, projector placement and type of screen to use are critical to the optimum use of the projection system.
INSTALLATION GUIDELINES INSTALLATION GUIDELINES * Which screen type? * Which screen type? There are two major categories of screens used for projection equipment. Those used for front projected images and those for rear projection applications. There are two major categories of screens used for projection equipment. Those used for front projected images and those for rear projection applications.
INSTALLATION GUIDELINES INSTALLATION GUIDELINES * Where to install the projector? * Where to install the projector? To indicate a correct installation position it is necessary to know the distance : - projector - ceiling - projector - screen To indicate a correct installation position it is necessary to know the distance : - projector - ceiling - projector - screen To find this correct position for the BARCOVISION 701 MULTIMEDIA, equipped with HD145 lenses, formulas are given in the next paragraph.
INSTALLATION GUIDELINES INSTALLATION GUIDELINES ceiling ceiling PD B CD PD B CD A A projector projector screen screen Front view Front view screen width SW 5975248 BARCOVISION 701 MULTIMEDIA 090797 3-5 Top view 5975248 BARCOVISION 701 MULTIMEDIA 090797 INSTALLATION GUIDELINES Top view INSTALLATION GUIDELINES screen width SW 3-5
INSTALLATION GUIDELINES * How to install the projector? * How to install the projector? Ceiling mount or table mount? To install the projector, apply always the BARCO kits which are specially designed for this function. Ceiling mount or table mount? To install the projector, apply always the BARCO kits which are specially designed for this function. BARCO ceiling support. BARCO ceiling support. Always use the BARCO ceiling support to attach your projector to the ceiling.
INSTALLATION SET UP INSTALLATION SET UP INSTALLATION SET UP INSTALLATION SET UP Access to controls Scan adaptation Scan adaptation 5975248 BARCOVISION 701 MULTIMEDIA 070597 4-1 INSTALLATION SET UP INSTALLATION SET UP Access to controls 5975248 BARCOVISION 701 MULTIMEDIA 070597 4-1
INSTALLATION SET UP INSTALLATION SET UP Access to controls Access to controls Opening procedure : Opening procedure : During the projector set up and installation it is necessary to open the top cover. During the projector set up and installation it is necessary to open the top cover. To gain access, handle as follow : To gain access, procede as follow : *Turn both lock screws with a screwdriver or a coin counter clockwise. *Turn both lock screws with a screwdriver or a coin counter clockwise.
INSTALLATION SET UP INSTALLATION SET UP During some installations it will become handy to remove the top cover totally. Therefore, - pivote the top cover ± 60° During some installations it will become handy to remove the top cover totally. Therefore, - pivote the top cover ± 60° - push the top cover to the front side of the projector until it jumps out of its hings. Turn the top cover till 90° and lift it up. - push the top cover to the front side of the projector until it jumps out of its hings.
INSTALLATION SET UP INSTALLATION SET UP Scan adaptation Scan adaptation The scanning can be switched by turning the Horizontal and Vertical scan connectors and the convergence connectors. To change the scanning, it is necessary to open the projector top cover and to rotate the chassis. For opening the projector's top cover, see Getting access to controls. The scanning can be switch by turning the Horizontal and Vertical scan connectors and the convergence connectors.
INSTALLATION SET UP INSTALLATION SET UP Horizontal scan connectors Horizontal scan connectors Vertical scan connectors Vertical scan connectors Convergence connectors RS232 IN RS232 OUT COMM PORT (800 peripherals) REMOTE R G(S) B S VIDEO Convergence connectors S-VIDEO RS232 OUT COMM PORT (800 peripherals) REMOTE 5975248 BARCOVISION 701 MULTIMEDIA 070597 4-5 R G(S) B S VIDEO S-VIDEO INSTALLATION SET UP INSTALLATION SET UP RS232 IN 5975248 BARCOVISION 701 MULTIMEDIA 070597 4-5
INSTALLATION SET UP INSTALLATION SET UP A : Horizontal scan inversion A : Horizontal scan inversion Three connectors are used, one for each horizontal deflection coil. When changing the horizontal scan, insure that all three connectors are set in the same position. See position of the connectors for the corresponding projector configuration. Three connectors are used, one for each horizontal deflection coil.
INSTALLATION SET UP INSTALLATION SET UP After scan inversion, close the chassis and close the top cover. Reconnect the power cord to the wall outlet. After scan inversion, close the chassis and close the top cover. Reconnect the power cord to the wall outlet. Note Switching over from floor to ceiling or vice versa requires a complete readjustment of picture geometry and convergence.
INSTALLATION SET UP The 'Projector set up menu' will be displayed. - Select with the control disk 'Identification' and press ENTER. INSTALLATION SET UP The 'Projector set up menu' will be displayed. - Select with the control disk 'Identification' and press ENTER. PROJECTOR SET-UP IDENTIFICATION TOTAL RUN TIME CHANGE PASSWORD CHANGE LANGUAGE CHANGE PROJECTOR ADDRESS CHANGE BAUDRATE POWER UP MODE : operating BARCO LOGO Select with or then to return.
PROJECTOR SET UP PROJECTOR SET UP PROJECTOR SET UP PROJECTOR SET UP PROJECTOR SET UP PROJECTOR SET UP Password mode Password mode 5975248 BARCOVISION 701 MULTIMEDIA 070597 5-1 5975248 BARCOVISION 701 MULTIMEDIA 070597 5-1
PROJECTOR SET UP PROJECTOR SET UP Projector Set Up Projector Set Up The strap on the CPU unit allow a set up of the password mode. The strap on the CPU unit allow a set up of the password mode.
PROJECTOR SET UP PROJECTOR SET UP Password mode Password mode With a strap on the controller unit, the important projector adjustments can be protected with a password. When the password feature is enabled (strap mounted on both legs), the customer has to enter a password before he can enter the specific adjustment. With a strap on the controller unit, the important projector adjustments can be protected with a password.
PROJECTOR SET UP PROJECTOR SET UP PROJECTOR SET UP 5-4 PROJECTOR SET UP 5975248 BARCOVISION 701 MULTIMEDIA 070597 5-4 5975248 BARCOVISION 701 MULTIMEDIA 070597
POWER CONNECTION POWER CONNECTION POWER (MAINS) CONNECTION POWER CONNECTION POWER CONNECTION POWER (MAINS) CONNECTION 5975248 BARCOVISION 701 MULTIMEDIA 090497 6-1 5975248 BARCOVISION 701 MULTIMEDIA 090497 6-1
POWER CONNECTION POWER CONNECTION Power (mains) cord connection Power (mains) cord connection Use the supplied power cord to connect your projector to the wall outlet. Plug the female power connector into the male connector at the front of the projector. Use the supplied power cord to connect your projector to the wall outlet. Plug the female power connector into the male connector at the front of the projector.
POWER CONNECTION POWER CONNECTION See installation instructions before connecting to the supply OFF ON - Push out the module. POWER CONNECTION - Push out the module. 5975248 BARCOVISION 701 MULTIMEDIA 090497 V NOM 120/230 Volt I MAX 5/2.5 AMP FREQ 60/50 Hz POWER CONNECTION OFF ON See installation instructions before connecting to the supply V NOM 120/230 Volt I MAX 5/2.
POWER CONNECTION POWER CONNECTION - Loosen both screws of the protective cover and take off the cover. - Loosen both screws of the protective cover and take off the cover. Retaining screws Retaining screws 120 V 230 V - Pull out the 'power selector plug' and re-insert it as illustrated, depending on the wall outlet in the room. - Re-mount the protective cover and secure with both screws. - Re-insert the module. - Put the plastic cover back and secure both retaining screws.
POWER CONNECTION POWER CONNECTION Switching on/off Switching on/off The projector is switched ON and OFF using the power (mains) switch ON/OFF. The projector is switched ON and OFF using the power (mains) switch ON/OFF. Pressed : ON Not pressed : OFF Pressed : ON Not pressed : OFF The projector can start now in the 'operational mode' (image displayed) or in the 'stand by mode', depending on the position of the 'power up' dip switch on the controller unit.
POWER CONNECTION POWER CONNECTION POWER CONNECTION 6-6 POWER CONNECTION 5975248 BARCOVISION 701 MULTIMEDIA 090497 6-6 5975248 BARCOVISION 701 MULTIMEDIA 090497
INSTALLATION ADJUSTMENTS INSTALLATION ADJUSTMENTS INSTALLATION ADJUSTMENTS INSTALLATION ADJUSTMENTS Overview flow chart installation mode Overview flow chart installation mode Scheimpfug adjustment Scheimpfug adjustment Optical lens focusing Optical lens focusing Raster centering 5975248 BARCOVISION 701 MULTIMEDIA 070597 7-1 CRT projection angle adjustment Alignment of the projector 5975248 BARCOVISION 701 MULTIMEDIA 070597 INSTALLATION ADJUSTMENTS Alignment of the projector INSTALLATION AD
INSTALLATION ADJUSTMENTS INSTALLATION ADJUSTMENTS Entering the adjustment mode Entering the adjustment mode ADJUSTMENT MODE ADJUSTMENT MODE Select a path from below: Select a path from below: GUIDED RANDOM ACCESS INSTALLATION SERVICE IRIS GUIDED RANDOM ACCESS INSTALLATION SERVICE IRIS source 1 source 1 Select with or then to return Select with or then to return Installation Service Guided Adjustment 5975248 BARCOVISION 701 MULTIMEDIA 070597 INSTALLATION ADJUSTM
INSTALLATION ADJUSTMENTS INSTALLATION ADJUSTMENTS Overview flow chart installation mode. Overview flow chart installation mode. LOOSEN THE 4 LENS MOUNTING NUTS ON EACH LENS, UNTIL THE TAG OF EACH SCHEIMPFLUG RING CAN BE MOVED TO ITS DESIRED POSITION (1.4 M, 2.4 M OR 4.0 M SCREEN WIDTH° to continue to return OPTICAL LENS FOCUSING SCHEIMPFLUG ADJUSTMENT 1. LOOSEN THE NUT ON THE REAR OF THE XXXX LENS, ROTATE THE LENS BARREL TO FOCUS THE CENTER OF THE IMAGE, THEN TIGHTEN THE NUT 2.
INSTALLATION ADJUSTMENTS INSTALLATION ADJUSTMENTS Installation mode start up Installation mode start up It will be necessary to perform several mechanical adjustments while in the installation mode. Remove the top cover in order to gain access to the adjustment points (see Access to controls). Two possible ways to enter the installation mode : It will be necessary to perform several mechanical adjustments while in the installation mode.
INSTALLATION ADJUSTMENTS Push the control disk up or down to highlight "Installation" and press ENTER. INSTALLATION ADJUSTMENTS Push the control disk up or down to highlight "Installation" and press ENTER.
INSTALLATION ADJUSTMENTS INSTALLATION ADJUSTMENTS When the password mode is active, your password will be asked. When the password mode is active, your password will be asked. Your password contains 4 digits. Your password contains 4 digits. a) Adjusting the projector with the RCU. a) Adjusting the projector with the RCU. Enter the digits with the numeric keys on the RCU. Enter the digits with the numeric keys on the RCU.
INSTALLATION ADJUSTMENTS INSTALLATION ADJUSTMENTS b) adjusting the projector with the local keypad. When the 'compose password' menu is displayed, select with the control disk the first digit of your password and press ENTER. Continue by selecting the second digit with the control disk and press ENTER. Handle in the same way for the third and fourth digit. b) adjusting the projector with the local keypad.
INSTALLATION ADJUSTMENTS INSTALLATION ADJUSTMENTS Scheimpfug adjustment Scheimpfug adjustment The scheimpfug correction can be adjusted separately for the three tubes within 3 ranges: The scheimpfug correction can be adjusted separately for the three tubes within 3 ranges: range 1 : 1.4 m (55") to 1.9 m (75"), optimum screen width 1.4 m (55") range 2 : 1.9 m (75") to 3.2 m (126"), optimum screen width 2.4 m (94") range 3 : 3.2 m (126") to 6 m (236"), optimum screen width 4 m (157") range 1 : 1.
INSTALLATION ADJUSTMENTS INSTALLATION ADJUSTMENTS 1. Open the top cover (see Gaining access to controls) 1. Open the top cover (see Gaining access to controls) 2. Loosen the lens bolts (do not remove them), and slide the lens to the front until the scheimflug ring can move freely (nutdriver 8 mm or screwdriver). 2. Loosen the lens bolts (do not remove them), and slide the lens to the front until the scheimflug ring can move freely (nutdriver 8 mm or screwdriver).
INSTALLATION ADJUSTMENTS INSTALLATION ADJUSTMENTS Optical lens focusing Optical lens focusing The optical focusing procedure is performed separately for each lens. The appropriate CRT will be switched on as the user proceeds through the optical focusing adjustment sequence. Each lens has two focus adjustment points, one at the rear of the lens and one at the front.
INSTALLATION ADJUSTMENTS INSTALLATION ADJUSTMENTS Electrical focusing Electrical focusing The electrical focus for red, green and blue is factory preset. When they have to be readjusted, follow the procedure as described below : - Ensure the lenses are correctly focused. - Open the top cover. - Adjust separately the focus control for red, green and blue for the sharpest image on the screen. The electrical focus for red, green and blue is factory preset.
INSTALLATION ADJUSTMENTS INSTALLATION ADJUSTMENTS Raster centering Raster centering The raster must be centered on the CRT screen surface of each tube, therefore, it is necessary to look into the lenses. The raster must be centered on the CRT screen surface of each tube, therefore, it is necessary to look into the lenses.
INSTALLATION ADJUSTMENTS INSTALLATION ADJUSTMENTS correct raster position correct raster position Press ENTER to activate the raster on the Blue CRT faceplate. Shift the blue raster with the control disk until the raster is centered on the CRT faceplate. Press ENTER to continue with the CRT projection angle adjustment 5975248 BARCOVISION 701 MULTIMEDIA 070597 ENTER continues to CRT Projection angle Adjustment. EXIT returns to Optical focusing. ADJUST returns to operational mode.
INSTALLATION ADJUSTMENTS INSTALLATION ADJUSTMENTS CRT projection angle adjustment CRT projection angle adjustment The projection angle of the red and blue CRT's is dependent on the desired size of the projected image. If the centers of green, blue and red do not coincide, the CRT projection angle must be adjusted. Never try to correct this misalignment with the shift correction or the static convergence controls.
INSTALLATION ADJUSTMENTS Projection angle correctly aligned for screen width SW1 INSTALLATION ADJUSTMENTS The same projection angle is mis-aligned for new screen width SW2. Re-alignment is necessary. Each screen width change requires readjustment of the projection angle.
INSTALLATION ADJUSTMENTS A' A Screws A, B, C and D (M4) : upper fixation latch. nutdriver 7mm. Screw A', B', C' and D' (M4) : lower fixation latch. nutdriver 7mm. A' A Loosen the four hexagon screws A, A', B and B', upper and lower fixation latch. These screws fasten the cooling house of the red tube. Pivot the red CRT until the center of the red image coincides with the center of the green image. If the angle of the red CRT is corrected, tighten the four bolts.
INSTALLATION ADJUSTMENTS blue crosshair green crosshair Move the bleu CRT to the outside, away from the green CRT Loosen the four hexagon screws C, C', Dand D', upper and lower fixation latch. These screws fasten the cooling house of the blue tube. Pivot the blue CRT until the center of the blue image coincides with the center of the green image. If the angle of the red CRT is corrected, tighten the four bolts.
INSTALLATION ADJUSTMENTS INSTALLATION ADJUSTMENTS Alignment of the projector. Alignment of the projector. Overview of the corrections Overview of the corrections For detailed information about these corrections and procedures to be followed, see owner's manual. (pages given hereafter are for the random access adjustment mode) For detailed information about these corrections and procedures to be followed, see owner's manual.
APPENDIX A : CEILING MOUNT KIT CM50 APPENDIX A : CEILING MOUNT KIT CM50 Ceiling mount kit for 700 projectors (CM50). Ceiling mount kit for 700 projectors (CM50). This ceiling mount with or without pulley system enables to mount the BARCO 700 projector to the ceiling. The concept makes it possible to adapt the projector perfectly to the local mounting requirements in a safe and solid manner.
APPENDIX A : CEILING MOUNT KIT CM50 APPENDIX A : CEILING MOUNT KIT CM50 APPENDIX A : CEILING MOUNT KIT CM50 A-2 APPENDIX A : CEILING MOUNT KIT CM50 5975248 BARCOVISION 701 MULTIMEDIA 090497 A-2 5975248 BARCOVISION 701 MULTIMEDIA 090497
APPENDIX B : G2 ADJUSTMENT APPENDIX B : G2 ADJUSTMENT G2 adjustment G2 adjustment Enter the adjustment mode by pressing ADJUST and highlight Service. Press ENTER to start up the service mode.
APPENDIX B : G2 ADJUSTMENT If you are qualified, press ENTER to continue with the G2 adjustment, otherwise press EXIT to return to the service menu. APPENDIX B : G2 ADJUSTMENT If you are qualified, press ENTER to continue with the G2 adjustment, otherwise press EXIT to return to the service menu. SAFETY NOTICE SAFETY NOTICE RISK OF ELECTRICAL SHOCK RISK OF ELECTRICAL SHOCK G2 ADJUSTMENT SHOULD BE PERFORMED BY BARCO PERSONNEL, OR BARCO AUTHORIZED DEALERS.
APPENDIX B : G2 ADJUSTMENT APPENDIX B : G2 ADJUSTMENT Switch ABL to OFF by pressing ENTER and adjust the G2 control until the raster brightness looks the same as when the ABL function is ON. Check the correct raster adjustment by pressing ENTER to toggle ABL to ON. Repeat these steps if necessary. Check the correct raster adjustment by pressing ENTER to toggle ABL to ON. Repeat these steps if necessary. Continue with the other colors. Use the right or left arrow key to select the next color.
APPENDIX B : G2 ADJUSTMENT APPENDIX B : G2 ADJUSTMENT APPENDIX B : G2 ADJUSTMENT B-4 APPENDIX B : G2 ADJUSTMENT 5975248 BARCOVISION 701 MULTIMEDIA 070597 B-4 5975248 BARCOVISION 701 MULTIMEDIA 070597