GRAPHICS 808s R9000901 - R9000908 R9000902 - R9000907 INSTALLATION MANUAL
BARCO PROJECTION SYSTEMS GRAPHICS 808s R9000901 - R9000908 R9000902 - R9000907 INSTALLATION MANUAL Date : 241197 Revision : 04 Art. No.
Due to constant research, the information in this manual is subject to change without notice. Produced by BARCO NV, November 1997. All rights reserved. Trademarks are the rights of their respective owners.
Table of contents Contents CHAPTER 1 SAFETY INSTRUCTIONS On safety .................................................................................................................................................... 1-1 On installation ............................................................................................................................................ 1-2 On servicing .....................................................................................................................
Table of contents CHAPTER 6 AC POWER CONNECTION AC Power cord connection ......................................................................................................................... 6-1 Preparing your power cord .......................................................................................................................... 6-1 Mains lead with CEE7 plug .....................................................................................................................................
Safety instructions 1 SAFETY INSTRUCTIONS Projectors are built in accordance with the requirements of the international safety standards IEC950, UL 1950 and CSA C22.2 No. 950, which are the safety standards of information technology equipment including electrical business equipment.
Safety instructions WARNING FOR THE USERS: THIS EQUIPMENT MUST BE GROUNDED (EARTHED) via the supplied 3 conductor AC power cable. (If the supplied power cable is not the correct one, consult your dealer.) A.
Unpacking and dimensions 2 UNPACKING AND PROJECTOR DIMENSIONS Unpacking To open the banding around the carton, pull out the clip as shown below : Take the projector out of its shipping carton and place it on a table. Save the original shipping carton and packing material, which will come in handy if you ever have to ship your projector. For maximum protection, repack your projector as it was originally packed at the factory.
POWER SUPPLY FRONT IR RECEIVER 590 510 576 558 456 590 BACK IR RECEIVER R7627612 R7627615 R7627616 816 806 A 286 CRT CRT POINT B 211 209 170 AIRFLOW AIRFLOW 84 R7626572 R7626575 R7626576 27 226 2-2 MAX 428 APPROXIMATE WEIGHT WITH HD8 LENS - 67 KG 45.5 148 136 *SERVICE* ROTATION COVER 596 169.
Installation guidelines 3 INSTALLATION GUIDELINES Installation guidelines Careful consideration of things such as image size, ambient light level, projector placement and type of screen to use are critical to optimize the use of the projection system. Environment Which screen type? Do not install the projection system in a site near heat sources such as radiators or air ducts, or in a place subject to direct sunlight, excessive dust or humidity.
Installation guidelines Where to install the projector ? To indicate a correct installation position it is necessary to know : The distance from projector to ceiling in case of Ceiling mounted or the distance from projector to floor in case of Table mounted; The distance from projector to screen. &HLOLQJ 3' % &' $ 3UR MHFWRU To find the correct position for the BARCOGRAPHICS 808s, equipped with HD8 lenses, use the following formulas: In metric : 6FUHHQ PD[m] = 1.269 x SW[m] + 0.
Installation setup 4 INSTALLATION SETUP WARNING : Risk of electric shock ! Installation only by BARCO authorized service personnel ! Access to Controls Opening the top cover During the projector setup and installation it is necessary to open the top cover. Follow the procedure described below : Turn the locking screw with a screwdriver counter clockwise; Lift up and pivot the top cover. WARNING : The projector's top cover is not supported with locking hinge.
Installation setup Scan Adaptation The scan switches must be placed in the correct position which corresponds to the desired scanning configuration. To change the scanning, it is necessary to remove the projector top cover and to open the protection plate. For opening the projector's top cover, see 'Access to controls'. WARNING ! TURN OFF PROJECTOR AND UNPLUG THE POWER CORD BEFORE CHANGING THE SCAN DIRECTION.
Installation setup Vertical Scan Switch One vertical switch is used for the three CRT's. See position of the switch (diagrams) for the corresponding projector configuration. To set the vertical scan switch : Remove the vertical deflection module (the third module viewing from the rear of the projector).
Installation setup To check the current positions of the scan switches, proceed as follows: Attention : This procedure can only be done after power (mains) connection. So, first continue with the projector setup and the connections and then return to this procedure. Switch on the projector. The projector starts up on the last selected source. Press the key.
Projector setup 5 PROJECTOR SETUP The DIP switches on the controller board allow the SETUP of the projector : 8 DIP switches for setting the projector address. 1 DIP switch for setting the powerup mode. 3 DIP switches for setting the baud rate for communication. 1 DIP switch for setting the password mode. To gain access to the DIP switches : - Open the top cover.
Projector setup Setting the address is a hardware SETUP of your projector which must be done during installation. Use the 8 DIP switches provided on the controller board labelled 'Projector Address'. Each DIP switch has its own decimal value. The sum of the values associated to those DIP switches gives the address. As shown in the table, if Switch No. 1 is set to ON, it represents a decimal value of 128, Switch No.2 for 64, Switch No.3 for 32, and so forth.
Projector setup Baud Rate for communication with a computer The communication speed between the projector and the computer has 8 possible settings. With DIP Switch No. 6, No.7 and No.8 of the 8 DIP switches on the controller board, labelled as Baud rate code (sum), it is possible to select the baud rate (communication speed). Each DIP switch has its own decimal value. The sum of the values associated to those DIP switches gives the baud rate code. Each baud rate code corresponds an communication speed.
AC power connection 6 AC POWER CONNECTION AC Power (mains) cord connection Use the supplied cord to connect your projector to the wall outlet. Plug the female power connector into the male connector at the back of the projector.
AC power connection AC Power check Check the power voltage which is determined by the ART. NR. (Article number) included in the label pasted on the backside of the projector. Projectors connected Projectors connected ART.NR.:RXXXXXXX $UW QU [[[[[[[[[ 6HULDO QU [[[[[[[ SER.NR.:RXXXXXXX with the ART. NR. R9000901 and R9000902 must be to a 230 VAC power source. with the ART. NR. R9000908 and R9000907 must be to a 120 VAC power source.
AC power connection Switching on the projector Push the power (mains) switch located on the rear panel of the projector to switch the projector ON and OFF : If the switch is pressed in : ON 9 QRP If the switch is Not pressed in : OFF 2)) 21 POW ER , QRP 9 )UHT $PS +] / M A IN S The projector can be started up in the 'Operational mode' (image displayed) or in the 'Standby mode', depending on the position of the 'Powerup' DIP switch on the controller board (see p.5-2).
Source connections 7 SOURCE CONNECTIONS Signal input connection The following signals can be connected to the projector through the inputs on the back panel of the projector : Composite Video 7KLV GH Y LF H F RP SOLH V ZLWK SDU W RI WKH )& & U XOH V 2SH U DWLRQ LV VXEMH F W WR I R OO R ZL Q J WZ R F R Q G L W LR Q V 7 K L V G LF \ QRW F V K I O LQW 6HH LQ VWDOODWLR Q LQ VWUX FWLR QV E HIR UH FR QQ HFWLQ J WR WKH VXS S O\ S-Video 9RLU OD Q R WLFH G LQ VWDOOD
Source connections Connecting a S-Video (or Composite Video) source to Port 2 Separate Y-luma/C-chroma signals for higher quality playback of Super VHS signals can be connected to Port 2 . The composite video can also be connected to this port. To select the S-video input : Press the numeric button 2 on the RCU or the local keypad.
Source connections Procedure to remove the line termination resistors : Turn off the projector and unplug the projector power cord. Unsolder and remove the resistors. Remove the top cover from the projector (see p.4-1). Remove the RGB Input Auto Sync Tracking Module from the main frame. To remove the RGB Input Auto Sync Tracking Module, follow the same procedure as described in p.
Source connections Connecting a RGB Analog source with Trilevel sync to Port 4/5 (option) 7KL V G HY LF H FR P S OLH V ZL WK SDUW RI WK H ) && UX OHV 2S HUD WLR Q L V V XE MH FW WR 6HH LQVW D O ODWLR Q L QVWUX FWLR QV E H I RUH FR QQ HF W LQJ WR WK H VXSS O\ IR OO R ZL Q J WZR FR QG L WL RQ V 9RL U OD Q RWL FH G LQVWDO ODWLR Q DY DQ W GH UDF FR UGHU DX U p VHDX G LF I Q F QG W K L V G FF LQF O RGB analog input terminals with Tri-level sync input or with Tri-lev
Installation adjustment mode 8 INSTALLATION ADJUSTMENT MODE Access to Installation Adjustment Mode It will be necessary to perform several mechanical adjustments while in the Installation Adjustment Mode. It will be required to open and remove the projector's top cover in order to gain access to the adjustment points.
Installation adjustment mode Important : Access to adjustments The top cover of the projector should be removed in order to gain access to the adjustments. Please refer to p.4-1 for how to remove the top cover. Projector Distance On the screen, a drawing will be displayed together with parameters indicating a correct installation position.
Installation adjustment mode Raster Centering The raster must be centered on the CRT faceplate of each tube, therefore, it is necessary to look into the lenses. 5$67(5 &(17(5,1* Caution : To avoid eye discomfort while performing these adjustments, reduce the contrast and gradually increase the brightness level until the raster becomes visible behind the image. Warning : In order to ensure maximum CRT longevity and to avoid CRT damage, do not shift the raster outside the phosphor area of the CRT.
Installation adjustment mode CRT Projection Angle Adjustment The projection angle of the red and blue CRT's is dependent on the desired size of the projected image. If the centers of green, blue and red do not coincide, the CRT projection angle must be adjusted. NOTE : Never try to correct this misalignment with the shift correction or the static convergence controls. These controls may only be applied to correct small errors which cannot be corrected by the CRT angle adjustment.
Installation adjustment mode Loosen bolts E, F, G and H to pivot the blue CRT until the center of the Blue image and the center of the Green image coincide. When the angle of the blue CRT is corrected, tighten the four bolts. Press the key to continue with the diagonal focusing menu. Press the key to return to the CRT projection angle adjustment.
Installation adjustment mode Scheimpflug Adjustment (Diagonal image focusing) With the diagonal image focusing corrections, it is possible to obtain uniform focus for the total projected image. ',$*21$/ ,0$*( )2&86,1* These corrections must be repeated for each color. The Diagonal image focusing is repeated 3 times, first for green, then for red and then for blue. 1. TURN THE SCREW MARKED 01 TO FOCUS THE IMAGE DIAGONALLY from LEFT (bottom) TO RIGHT (top). 2.
Messages, warnings and failure codes 9 MESSAGES, WARNINGS AND FAILURE CODES SOURCE 01 Fh= 15.6 kHz Fv= 050 Hz SOURCE 01 Fh= 15.6 kHz Fv= 050 Hz enter password xxxx text on text off PROJECTOR ADDRESS : 003 WARNING : input not available When selecting a new source, information about this source will be displayed on the screen. Source number, horizontal and vertical frequencies of the displayed source. Announcement of the selected source. Message to enter your password. Password contains 4 digits.
Messages, warnings and failure codes WARNING : Projector will switch to 'Standby' when the RCVDS is no longer available. FAILURE RCVDS communication error WARNING : invalid frequency input The entered frequency or applied frequency of the source is out of the projector's range. FAILURE RWI communication error Hardware failure. Call a qualified service technician. WARNING : default settings loaded in the E2PROM Adjustment settings are lost.
Appendix A: BARCO ceiling mount support A BARCO CEILING MOUNT SUPPORT This appendix gives only an overview of the contents of the installation guidelines and some overview drawings. The installation guidelines for the BARCO ceiling mounting support can be ordered from BARCO. The order number: R5975693. Contents of the installation guidelines Overview drawing of the total system 1. Mounting instructions for the upper support to the ceiling a. Position of the upper support on the ceiling b.
Appendix A: BARCO ceiling mount support Projector position corrections Water-level adjustment D Projector axis adjustment C A-2 5975996 BARCOGRAPHICS 808s 241197
Appendix B: G2 adjustment B G2 ADJUSTMENT Once the on-screen menu "G2 ADJUSTMENT" is displayed, proceed as follows : * $'-8670(17 Use the potentiometers on the G2-ADJ. module to set the screen grid voltage for Red, Green and Blue. Adjust until the LED on the corresponding output amplifier is turned off. to return Remove the top cover from the projector (see p.4-1) and open the front metal protection cover by turning out the 3 retaining screws on both sides.
Gamma corrections C GAMMA CORRECTIONS When entering the gamma corrections, a warning will be displayed : "RISK OF INCORRECT ADJUSTMENT OF THE PROJECTOR. THE GAMMA CORRECTIONS ARE FACTORY ADJUSTED USING AN ACTAS COLOR ANALYZER ! THEREFORE, ONLY QUALIFIED INSTALLATION OR SERVICE PERSONNEL SHOULD PERFORM THESE ADJUSTMENTS ! " If you are qualified, press the key to continue.
Gamma Corrections To carry out the Red and Blue Midlights Correction : Push the control stick forward or backward to highlight the item R & B MIDLIGHTS in the menu and then press the key. If the key is pressed, the projector will return to the Service menu. After the key is pressed, a text box with the message "Adjust with arrow key", will be displayed on the screen.
Form Approved Bureau Budget No. 45-R0338 MATERIAL SAFETY DATA SHEET MANUFACTURER'S NAME AND FSCM (Federal Supply Code for Manufacturer's) BARCO N.V. EMERGENCY PHONE NO.
SECTION V HEALT HAZARD DATA TRESHOLD LIMIT VALUE EFFECTS OF OVEREXPOSURE EMERGENCY AND FIRST AID PROCEDURES STABILITY SECTION VI REACTIVITY DATA 100ppm CONDITIONS TO AVOID UNSTABLE STABLE X INCOMPATABILITY (Materials to avoid) HAZARDOUS DECOMPOSITION PRODUCTS HAZARDOUS POLYMERIZATION MAY OCCUR X CONDITIONS TO AVOID WILL NOT OCCUR SECTION IX SPECIAL PRECAUTIONS SECTION VIII - SPECIAL PROTECTION INFORMATION SECTION VII SPILL OR LEAK PROCEDURES STEPS TO BE TAKEN IN CASE MATERIAL IS RELEASED
