BARCO PROJECTION SYSTEMS DATA 2100 R9001070 INSTALLATION MANUAL Date: 100696 Art. No. :R5975846 Rev. : 01 BARCO PROJECTION SYSTEMS DATA 2100 R9001070 INSTALLATION MANUAL Date: 100696 Rev. : 01 Art. No.
Due to constant research, the information in this manual is subject to change without notice. Produced by BARCO NV, November 1996 All rights reserved. Trademarks are the rights of their respective owners. Printed in Belgium Due to constant research, the information in this manual is subject to change without notice. Produced by BARCO NV, November 1996 All rights reserved. Trademarks are the rights of their respective owners.
Table of contents WARNINGS & TABLE OF CONTENTS ....................................................................................................................................... 1-1 AVERTISSEMENTS & PRESCRIPTIONS DE SECURITE .......................................................................................................... 1-1 Remarque sur la Sécurité ..................................................................................................................................................
Safety Instructions WARNINGS AVERTISSEMENTS Safety instructions Prescriptions de sécurite On safety sécurité On installation installation On servicing entretien et réparation On cleaning nettoyage On repacking re-emballage On illumination éclairage 5975846A BARCODATA 2100LC 200596 1-1 Safety Instructions WARNINGS AVERTISSEMENTS Safety instructions Prescriptions de sécurite On safety sécurité On installation installation On servicing entretien et réparation On cleaning nettoyage On repacking re-emballage
Presciptions de sécurité Remarque sur la Sécurité DONNEES POUR LE PROPRIETAIRE Les projecteurs sont fabriqués conformément aux exigences des normes de sécurité internationales EN60950, UL 1950 et CSA C22.2 No. 950. Ces normes de sécurité sont imposées aux équipements de la technologie informatique incluant les équipements électriques. Le numéro de pièce et le numéro de série sont situés à l’arrière du projecteur. Copier ces numéros dans les espaces prévus ci-dessous.
Safety Instructions Notice on safety OWNER’S RECORD Projectors are built in accordance with the requirements of the international safety standards EN60950, UL 1950 and CSA C22.2 No. 950, which are the safety standards of information technology equipment including electrical business equipment. The part number and serial number are located at the rear of the projector. Record these numbers in the spaces provided below. Refer to them whenever you call upon your BARCO dealer regarding this product.
Presciptions de sécurité ATTENTION RISQUE D'ELECTROCUTION NE PAS OUVRIR ATTENTION : AFIN DE REDUIRE LE RISQUE DE CHOCS ELECTRIQUES, NE PAS ENLEVER LE COUVERCLE (OU LE DOS) IL N'Y A PAS DE PIECES REPARABLES PAR L'UTILISATEUR A L'INTERIEUR LE SERVICE NE PEUT ETRE EFFECTUE QUE PAR DU PERSONNEL QUALIFIÉ L’éclair avec une tête de flèche dans un triangle indique à l’utilisateur que les pièces à l’intérieur de l’appareil présentent un risque de chocs électriques.
Safety Instructions The lightning flash with an arrowhead within a triangle is intended to tell the user that parts inside this product are risk of electrical shock to persons. The exclamation point within a triangle is intended to tell the user that important operating and/or servicing instructions are included in the technical documentation for this equipment.
Presciptions de sécurité toutes les mesures requises pour les amoindrir, à ses propres frais. mise à la terre. Le connecteur n’est adapté qu’à des prises de courant du type avec terre. Ceci est une mesure de sécurité. Si le connecteur Instructions pour l’utilisateur : ne s’adapte pas dans la prise, contacter votre électricien pour Si cet équipement cause des interférences de radio ou de télévision, remplacer la prise non valable.
Safety Instructions Instructions to the user : plug into the outlet, contact your electrician to replace your obsolete outlet. Do not defeat the purpose of the grounding-type plug.
Presciptions de sécurité * Ne jamais introduire un objet quelconque dans l’appareil à travers * Les fentes et les ouvertures pourvues dans le boîtier et au dos ou les fentes du boîtier, car ils pourraient être en contact avec des sur le fond, sont destinées à la ventilation. Pour assurer un fonctionpoints de tension dangereux ou court-circuiter des pièces, ce qui nement fiable du projecteur et le protéger de toute surchauffe, ses ouvertures ne doivent être ni obstruées ni recouvertes.
Safety Instructions * Never push objects of any kind into this product through cabinet slots as they may touch dangerous voltage points or short out parts that could result in a risk of fire or electrical shock. product on a bed, sofa, rug, or other similar surface. This product should never be placed near or over a radiator or heat register. This projector should not be placed in a built-in installation or enclosure unless proper ventilation is provided. * Never spill liquid of any kind on the product.
Presciptions de sécurité - Si l’ appareil ne fonctionne pas normalement, bien que les instruc- Nettoyage tions soient correctement suivies. Ne régler que les commandes décrites dans les instructions de fonctionnement, car un mauvais Débrancher l’appareil de la prise avant tout nettoyage. Ne pas utiliser réglage d’autres commandes peut entraîner des dégâts et souvent des détergents liquides ou des aérosols.
Safety Instructions instructions are followed. On Cleaning Adjust only those controls that are covered by the operating instructions since improper adjustment of the other controls may Unplug this product from the wall outlet before cleaning. Do not use result in damage and will often require extensive work by a qualified liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.
Presciptions de sécurité Lors de l’installation du projecteur et de l’écran, il faut veiller à éviter toute exposition directe de l’écran à la lumière ambiante. Eviter tout éclairage perturbateur sur l’écran par des rayons du soleil ou des éclairages fluorescents. L’utilisation d’un éclairage ambiant contrôlable, tel qu’un spot incandescent ou un variateur de lumière est recommandée pour obtenir un éclairage correct de la pièce.
Safety Instructions When installing the projector and screen, care must be taken to avoid exposure to ambient light directly on the screen. Avoid adverse illumination on the screen from direct sunlight or fluorescent lighting fixtures. The use of controlled ambient lighting, such as incandescent spot light or a dimmer, is recommended for proper room illumination.
Power Connection POWER CONNECTION 2-1 5975846 BARCODATA 2100 100696 Power Connection POWER CONNECTION 5975846 BARCODATA 2100 100696 2-1
Power Connection Power (mains) cord connection Use the delivered power cord to connect your projector to the wall outlet. Plug the female power connector into the male connector at the front of the projector. SOURCE 5 SOURCE 4 RGBH/CV RGBH/CV R R G G B B H/ C H/ C SOURCE 1 VIDEO SOURCE 2 VIDEO The power voltage for the projector is indicated on the identification plate on the rear of the projector.
Power Connection Input Power (mains) voltage adaptation Attention The BARCODATA 2100 - R9001070 leaves the factory to operate on a mains (power) input of 230Vac. Adaptation of the power input of the projector from 230 Vac to 120Vac or vice versa is possible. Follow the procedure as described below. Procedure : - Unplug the power cord from the power input on the front panel. - Turn both lock screws of the top cover with a screwdriver or coin counter clockwise.
Power Connection The switched mode power supplied is located on right side of the projector. - Remove the black protection plate by turning out the 5 screws (indicated with a white arrow) and loosening the both screws (indicated with a hand). Slide the plate a little to the left and take the plate off. - Pull the power module a little to the front until the power selector plug is reachable.
Power Connection -Pull out the 'power selector plug' and re-insert it as illustrated, depending on the walll outlet of the room. - Close the top cover and secure with both locking screws. Fuses Warning For continued protection against fire hazard : - replace with the same type of fuse. - refer replacement to qualified service personnel Fuse type : T12.5 AH/250V Order no.
Power Connection Switching on Use the power switch to switch on. When '0' is visible, the projector is switched off. When '1' is visible, the projector is switched on.
Power Connection When the total run time of the lamp is 970 hours or more, the following message will be displayed for 1 minute. This message will be repeated every 30 minutes. Press EXIT to remove the message before the minute is over. When the total run time of the lamp is 1000 hours or more, the following message, with the exact run time is displayed on the screen. Lamp run time 980 h Lamp run time is 1000 hours. Operating the lamp longer than 1000 hours may damage the projector.
Power Connection Switching off To switch off: - press first STANDBY key and let cool down until the fans stop blowing ( or at least 15 min). - switch off the projector with the power switch. 2-8 5975846 BARCODATA 2100 100696 Power Connection Switching off To switch off: - press first STANDBY key and let cool down until the fans stop blowing ( or at least 15 min). - switch off the projector with the power switch.
Password set up PASSWORD SET UP 3-1 5975846 BARCODATA 2100 270396 Password set up PASSWORD SET UP 5975846 BARCODATA 2100 270396 3-1
Password set up How to enable or disable the password function ? The password function is enabled when the password strap on the controller module is installed. To get acces to the controller module, handle as follows : - Power down the projector and disconnect the power cord from the wall outlet. - Turn both lock screws of the top cover with a screwdriver or coin counter clockwise. - Lift up and pivot the top cover a little and pull it to the back to remove.
Password set up When the strap is on the right leg and the middle leg, the password function is enabled, when the strap is on the left leg and the middle leg, the password function is disabled. Password enabled Password disabled 3-3 5975846 BARCODATA 2100 270396 Password set up When the strap is on the right leg and the middle leg, the password function is enabled, when the strap is on the left leg and the middle leg, the password function is disabled.
Password set up How to change the password ? Highlight Change password by pushing the control stick forward or backward and press ENTER to display the Change Password menu. ENTER displays the Change Password menu EXIT returns to the adjustment selection menu. The old password is displayed and can be changed by entering the digit with the numeric keys of the RCU or local keypath. SERVICE IDENTIFICATION CHANGE PASSWORD CHANGE PROJ.
100% OFF-AXIS Projection 100% OFF-AXIS PROJECTION 4-1 5975846 BARCODATA 2100 191196 100% OFF-AXIS Projection 100% OFF-AXIS PROJECTION 5975846 BARCODATA 2100 191196 4-1
100% OFF-AXIS Projection How to modify the projector for 100% off-axis projection. Note : 100% off axis projection is only possible with the SD(1.7:1) lens. a. Mount first the 2 supporting feet extensions. Handle as follows : - Turn the projector upside down. - Remove both plastic supporting feet (see fig. 1) by turning them anti clockwise. Fig. 1 Fig. 2 5975846 BARCODATA 2100 191196 4-2 100% OFF-AXIS Projection How to modify the projector for 100% off-axis projection.
100% OFF-AXIS Projection Mount the extensions by turning them in clockwise. Turn in the plastic supporting feet in the extensions. Place the projector on its feet. Adjust the projector feet until the projector is water leveled. 5975846 BARCODATA 2100 191196 4-3 100% OFF-AXIS Projection Mount the extensions by turning them in clockwise. Turn in the plastic supporting feet in the extensions. Place the projector on its feet. Adjust the projector feet until the projector is water leveled.
100% OFF-AXIS Projection b. Adjust the fresnel lens to correct the keystone. To get access to the fresnel lens, handle as follows : - Turn both lock screws of the top cover with a screwdriver or coin counter clockwise and left up and pivot the top cover. See also 'How to enable or disable the password function ?' in chapter 'Password set up'. The fresnel lens is mounted in the front part of the projector.
100% OFF-AXIS Projection - Turn slowly the lens unit to the front of the projector until the keystone distorsion is eliminated. Caution : Do not touch the lens unit with your fingers. Secure the correct position by fastening both locking screws. - Re-install the top cover. 5975846 BARCODATA 2100 191196 4-5 100% OFF-AXIS Projection - Turn slowly the lens unit to the front of the projector until the keystone distorsion is eliminated. Caution : Do not touch the lens unit with your fingers.
BARCO nv/Projection Systems Noordlaan 5 B-8520 Kuurne Belgium Printed in Belgium BARCO nv/Projection Systems Noordlaan 5 B-8520 Kuurne Belgium Printed in Belgium
