Pre-assembly 2+ 1.Two or more people are required for assembly. 2.You will need one or more stepladders. 3. Wearing protective gloves is recommended. 4.You may need a safety hat. 5.Please use a Phillips screw driver. 6.For ease of construction, you may need a drill. 7.You may need a safety goggle. 8.Do not fully tighten screws prior to complete assembly.
0">.-· _. I\ I- ·V \ 闷 @ 4x . . . 2x 严 \ @) @2x . . @) ·. L=70x27x1490mm ·. 心 . \. @) 1x L=100x25x1565mm 闷 @ 1x L=100x25x1250mm . \ / 国 1x ., L=100x25x1565mm -� ·:. 固 畴 . \. . \· . \,., \ \ 蛐 丘) . . / / 2x L=70x27x1478mm @ 1x \ 豆 1x 0 2x ·. . L=70x25x1490mm . . . 一. .一 L=100x25x1565mm 1x . \. 1x L=70x25x1478mm \ � 1x L=100x25x1565mm @) . . . \ \ \ / 1x L=100x25x1250mm . \" ·.· \ / 1x L=70x27x1478mm . 姜〉 L=70x27x1490mm @ 1x
Part list L=019x1720mm 田) 向 5x L=016x1747mm 勹) s u L=016x1747mm 勺) u L=016x1747mm 闷 L=20x1Ox1747mm 令 冈 尧 辜 3 支 团 2x 5x u [J ( s ( u () V () 1x s e � cg) 1x @ 1x 但) s L=20x1Ox1747mm ,。? ! 1x () 1x s 5x () 1x L=016x1747mm 冈 L=019x1720mm (.) ]t rt @ 1x ` 团 32x 冈 2x ®ax 『 勹 1x 三 伈) 1x S4 S6 二二二二二二心 宅 @ 1x @ 1x `卵 函 荽) 10x 4x `勒 M6x15 M6x20 @ 3x M6x16 � � m (Dasx 吵雪卿 @3 x M6x28 moo 困 6x llllllllllllD M6x85
Step1: Connect part A1 and part A, part A2 and part A on the side of the wall using screws 1# and part B1 as shown in diagram. `严 Then connect part A2 and part A, A1 and part A on the other side using screws 1# and part B.
Step 2: @ 1x @) 1x @) 1x @) 1x As shown in the figure, use screws 1# to connect part C and C1, and also connect part C2 and C3 together. At the same time, connect five sliders (part S2) on each side.
'I OI)严 Step 3: Link part D and part D1, part D and part D2 using screws 1# as shown in diagram1# as shown in diagram. And link part E and part E1, part E and part E2 using screws 1# as shown in diagram.
Step 4: Link part F and F1, part G and G1 using screws 1# as shown in diagram. And connect the sliders(part S1 and part S). Then hang part R on the outside slider of part G1.
c= 团 16x Step 5: M6x15 V @ 1x , M6x15 Connect part D2 with A1, D1 with A2 using screws 2# as shown in diagram. Also, connect part E1 with A2, E2 with A1 using screws 2# as shown in diagram. Step 6: @16x � @ 1x 8 Connect part C2 with A1, C3 with A2 using screws 2# as shown in diagram. Also, connect part C with A2, C1 with A1 using screws 2# as shown in diagram.
`阶 困 )))ll)))l))))) M6x85 3x S4 @ 1x Step 7: As shown in the figure, use screws 5# to connect part F with beams (part D1&D2), and also connect part F1 with beams (part E1&E2). Then connect part G and G1 with beams (part D&E) in the same way. Step 8: Insert part J&J1 into the pocket of top roof (part M) as shown in diagram, then insert part H&H1 into the pocket of top roof in turn.
Step 9: Insert part L&K, L1&K1 into the part M1 using part N.
团 G) ()] 00M6x16 7x `@ M6x20 3x `雹! 困 3x 1111111111111) M6x85 S4 @ 1x 11 Step 10: Secure the part M1 to the top.
。 `严 2 10x 8) M6x16 m®»一 3x M6x28 Step 11:Connect part J and part D1 and connect part H and part H1.
Step 12 : When the canopy is folded, hang the other end of string (part R) into the hole on the inside of beam (part E) to secure the top roof. ® 8 / 今 .“ , Step 13: 13 Insert stakes (part P) through the hole of stand plate (part B) into the ground, to stabilize the tent.