User's Guide

ManualsBrandsBanner Engineering ManualsElectronicsFREQUENCY HOPPING SPREAD SPECTRUM TRANSMITTER

SureCross™ 1 Watt Data Radio

WARNING…

Not to be used for personnel protection

Never use these products for personnel protection. Doing so could lead to serious injury or death.

These products do NOT include the self-checking redundant circuitry necessary to allow their use in personnel safety

applications. A failure or malfunction can cause either an energized or de-energized product output condition. Consult your

current Banner Safety Products catalog for safety products that meet OSHA, ANSI, and IEC standards for personnel protection.

Printed in USA 10/07 P/N 132031

Features

Data radios may be used to expand a Modbus network or avoid obstacles in the path of

the radio signals.

Wireless industrial device to extend the range of a Modbus network

+10 to 30V dc power input

Data routing controlled by Modbus slave IDs

Radio networks use unique network IDs

Frequency Hopping Spread Spectrum (FHSS) technology and Time Division

Multiple Access (TDMA) control architecture combine to ensure reliable data

delivery within the unlicensed Industrial, Scientific, and Medical (ISM) bands

Transceivers provide two-way communication between radios

For additional information and a complete list of accessories, including FCC approved

antennas, please refer to Banner Engineering’s website, www.bannerengineering.com/

surecross.

•

Model Power Frequency Master/Slave Serial Type

DX87M9S2

10 to 30V dc

900 MHz ISM Band

Master

RS232

DX87S9S42 Slave

DX87M9S4 Master

RS485

DX87S9S4 Slave

DX87M2S2

2.4 GHz ISM Band

Master

RS232

DX87S2S42 Slave

DX87M2S4 Master

RS485

DX87S2S4 Slave

Models

Summary of content (8 pages)

PAGE 1
SureCross™ 1 Watt Data Radio SureCross™ 1 Watt Data Radio Features Data radios may be used to expand a Modbus network or avoid obstacles in the path of the radio signals.
PAGE 2
SureCross™ 1 Watt Data Radio Overview Serial radios connect a Modbus control system to one or more DX80 Gateway devices acting as Modbus slaves. The data radios do not use addressing, error checking, or acknowledgement in the radio packets. Instead, the data stream appearing on the serial input of one radio within the network is reproduced on the serial outputs of all other radios in the same network. Addressing and error connection occur at the application layer.
PAGE 3
SureCross™ 1 Watt Data Radio This concept can be expanded indefinitely by chaining independent data radio connections through the serial interface. Very large networks can be created without complex network addressing. Modbus networks can be extended almost without limit while still maintaining the determinism and latency of the underlying TDMA networks. Modbus Master NID A NID A NID 1 NID A NID 2 NID B NID 1 NID 2 NID 1 NID 2 NID B NID 3 Banner Engineering Corp. • Minneapolis, MN U.S.A. www.
PAGE 4
SureCross™ 1 Watt Data Radio Hookup Diagrams 5-pin M12 Euro Hookup Color Brown White Blue Black Gray No.
PAGE 5
SureCross™ 1 Watt Data Radio Banner Engineering Corp. • Minneapolis, MN U.S.A. www.bannerengineering.com • Tel: 763.544.
PAGE 6
SureCross™ 1 Watt Data Radio FCC Certification - 900 MHz, 1 Watt Radio FCC Certification The DX80 Module complies with Part 15 of the FCC rules and regulations. FCC ID: UE3RM1809 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
PAGE 7
SureCross™ 1 Watt Data Radio Specifications Many of the DX80 parameters are configurable. The values in the tables represent factory defaults unless otherwise noted. General Power* +10 to 30V dc (For European applications: +10 to 24V dc, ±10%) Power Consumption Mounting #10 or M5 (M5 hardware included) M5 fasteners – Max. Tightening Torque 0.56 N•m (5 in•lbf) Case Material Polycarbonate Weight 0.26 kg (0.57 lb.
PAGE 8
SureCross™ 1 Watt Data Radio Specifications, continued Compliance 900 MHz Models FCC ID UE3RM1809: This device complies with FCC Part 15, Subpart C, 15.247 IC: 7044A-RM1809 Notice: This equipment must be professionally installed. The output power must be limited, through the use of firmware or a hardware attenuator, when using high-gain antennas such that the +36 dBm EIRP limit is not exceeded. The manufacturer does not take responsibility for the violation of any warning listed in this document.