BeoLab 7–1 Guide
CAUTION: To reduce the risk of electric shock, do not remove cover (or back). No User-serviceable parts inside. Refer servicing to qualified service personnel. WARNING: To prevent fire or electric shock, do not expose this appliance to rain or moisture. Do not expose this equipment to dripping or splashing and ensure that no objects filled with liquids, such as vases, are placed on the equipment.
Daily use When you have finished setting up the loudspeaker as described on the following pages, connect the entire system to the mains. 3 Cleaning the loudspeaker Clean dusty surfaces using a dry, soft cloth. If necessary, remove grease stains or persistent dirt with a lint-free, firmly wrung cloth, dipped in a solution of water containing only a few drops of mild detergent, such as washing-up liquid.
Set up the loudspeaker 4 We recommend that you follow this procedure: – Disconnect your Bang & Olufsen system from the mains. – Place the loudspeaker according to the guidelines on this page. – Use the enclosed accessories to mount the loudspeaker to the BeoVision stand or wall bracket as explained on the next page. – Connect the loudspeaker as explained in ‘Cable connections’ (pp. 6–7). – Set the POSITION switch to the correct setting. This is explained in ‘Adapt the loudspeaker to your room’ (pp. 8–9).
On this page is shown how to fasten the loudspeaker to a BeoVision 7* stand or wall bracket. If you wish to use the loudspeaker with another Bang & Olufsen system, refer to the Guide enclosed with the system. b c a c d d c c *NOTE! BeoVision 7 and its accessories are not available on all markets. Adjustments: First, make sure that the television is adjusted to a level position on its stand or wall bracket.
Cable connections 6 The loudspeaker is primarily intended to be used in a setup with BeoVision 7*. It may, however, be used with other Bang & Olufsen systems as well. If used in a setup not including BeoVision 7, you will require a mains cord and a Power Link cable. These cables are available as optional accessories from your Bang & Olufsen retailer. Mains connection to the television POWER LINK socket POSITION switch The socket panel is located on the rear of the loudspeaker.
Connection to BeoVision 7… Connect the loudspeaker to one of the Power Link sockets on the left BeoVision 7 socket panel. BeoVision 7 For further information about the BeoVision 7 socket panels, refer to the Guides enclosed with the product. BeoLab 7–1 Cable clamp: For safety reasons, the mains cord from the wall outlet must be secured to the loudspeaker. To do so, tug the cord behind the clamp. The two mains cords and the Power Link cable are enclosed with BeoVision 7.
Adapt the loudspeaker to your room 8 When a loudspeaker is placed in a corner or close to a wall, the bass level is boosted compared to the bass level from a loudspeaker placed in a more free-standing position. The POSITION switch The POSITION switch has two settings – F and W: F W • F (Free-standing position) Use this setting if the loudspeaker is placed so that the front grill is more The POSITION switch is located on To remove this excessive bass than 50 cm (20") from the rear wall, the socket panel.
Setup examples The three examples to the left all show the loudspeaker placed more than 50 cm (20") from the rear wall – and therefore the POSITION switch should be set to F. F F F The four examples to the right all show the loudspeaker placed closer than 50 cm (20") from the rear wall – and therefore the POSITION switch should be set to W.
For the Canadian market only! This class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. This product fulfils the conditions stated in the EEU directives 89/336 and 73/23. For the US-market only! NOTE: This equipment has been tested and found to comply with the limits for a class B digital device, To get access to the approval pursuant to part 15 of the FCC Rules.
www.bang-olufsen.