BandLuxe R100 3.
Table of Contents Table of Contents Table of Contents .....................................................................1 Package Contents ....................................................................3 Package Contents.................................................................................3 Features ................................................................................................4 Hardware Overview............................................................................
Table of Contents Management ...................................................................................... 41 Diagnosis............................................................................................ 43 Recover & Renewal............................................................................ 44 Status ...................................................................................... 46 3.5G HSPA & Internet........................................................................
Package Contents Package Contents Thank you for your purchase of this 3.5G WiFi Router. This product is designed to access the Internet via 3.5G technology and share the bandwidth through a WiFi network. It is easy to configure and operate even for non-technical users. This manual contains instructions for installing and configuring the product. Read the manual carefully before you use the product, so that you can fully exploit the product functions. Package Contents BandLuxe R100 3.
Package Contents Features - Share mobile broadband access for multiple users. - Router on the road, data card on the move. - 3.5G ExpressCard for WAN access supported. - Compatible with 802.11b and 802.11g clients. - Compact & Stylish Design. Hardware Overview 1 ExpressCard Slot Connect a BandLuxe C100/C100S HSDPA ExpressCard or a compatible data card. 4 2 Factory Reset button To reset the Router, press the reset button briefly.
Package Contents 5 USB Port 6 Receptor Receptor for the Power Adaptor. 7 UMTS LED A solid light shows the Router is connected to a mobile network and ready. When green, the mobile network is in 3G mode. When blue, the mobile network is in 3.5G mode. When purple, the mobile network is in GPRS mode. A blinking light indicates that the Router is not connected to a mobile network or not ready. If the LED light is not lit, there is no link between the data card and the Router.
Installation Installation 1. Connect the power adaptor to the Router and connect it to an outlet. 2. Insert your SIM card into the slot on the BandLuxe C100/C100S data card, making sure the SIM card orientation matches the SIM card slot, as shown in the picture. Then insert the BandLuxe data card into the Router. Note: Please use the ExpressCard/USB switch in the back of the Router to select the interface. Only one of the interfaces can be used at a time.
Installation 3. One of the following two methods can be chosen to link your Router with PC. A. To link the Router with your PC via WiFi, in Microsoft Windows, go to Control Panel > Network Connections, right-click on Wireless Network Connection,.and choose View Available Wireless Networks. Select the HSPA_ROUTER wireless network, and click Connect. B.
Installation Enter the Router user name (admin) and password (hsparouter).
Internet Setup Internet Setup Basic Setting Connection Type The 3.5G HSPA Router can link to the internet via 3.5G HSPA or Ethernet. Select the connection type you prefer. 3.5G HSPA Setting Get Latest APN Database Get the latest Profile Name, Number, User Name, Password, and APN from the web site automatically. Roaming Connection To allow roaming network connection, select Enabled. To block roaming connection, select Disabled. Note: Charges for roaming connection may be high.
Internet Setup APN Setting The APN (Access Point Name) is provided by your mobile network operator. You can choose to set the APN automatically or manually. In most cases, the 3.5G Router works properly when the APN is set to Auto. To set the APN manually, contact your mobile network operator for the APN, User Name and Password of the data service. Connection On Demand: You can set the idle time for the 3.5G HSPA connection.
Internet Setup PPPoE Choose PPPoE (Point to Point Protocol over Ethernet) if your ISP uses a PPPoE connection. Your ISP will provide you with a username and password. This option is typically used for DSL services. Service Name: Enter the ISP Service Name (optional). Connect on Demand: Enter a maximum idle time during which the Internet connection is maintained during inactivity. Keep Alive: If you select this option, the Router will periodically check your Internet connection.
Internet Setup Subnet Mask: This is the Router’s Subnet Mask, as seen by users on the Internet (including your ISP). Your ISP will provide you with the Subnet Mask. Server IP Address: Enter the Server IP provided by your ISP (optional). L2TP Choose L2TP (Layer 2 Tunneling Protocol) if your ISP uses a L2TP connection. Your ISP will provide you with a username and password. Internet IP Address: Enter the IP address provided by your ISP.
Internet Setup DDNS DDNS (Dynamic DNS Service) is a system which allows the domain name data held in a name server to be updated in real time. It allows an Internet domain name to be assigned to a computer with a varying (dynamic) IP address. Before you can use this feature, you need to sign up for DDNS service with a DDNS service provider, www.dyndns.org or www.TZO.com. Service Type: From the drop-down list, select your DDNS service type. User name: Enter the user name for your DDNS account.
Internet Setup Optional Host Setting Host Name and Domain Name These fields allow you to assign a host and domain name for the Router. Some ISPs require these names as identification. In most cases, leaving the fields blank will work. MTU MTU (Maximum Transmission Unit) specifics the largest packet size permitted for Internet transmission. To have the Router select the best MTU for your Internet connection, keep the default setting, Auto.
Internet Setup Time Setting Select the Time Zone from the drop-down menu according to your current location. Automatically adjust clock for daylight saving changes: Select the checkbox to enable Daylight Saving time.
Router Setup Router Setup Network Setting Router IP This is the Router’s IP address and subnet mask which is seen in your local network. The default IP address is 192.168.1.1, and the default Subnet Mask is 255.255.255.0. Keeping the default values will work. DHCP Service DHCP stands for Dynamic Host Control Protocol. The DHCP Server will automatically assign an IP address to the computers on the LAN/private network.
Router Setup DHCP Reservation To assign the same IP address to a PC every time it reboots, click the DHCP Reservation button. A list of DHCP clients is displayed with the following information: Client Name, Interface, IP Address, and MAC Address. Select a checkbox to reserve a client’s IP address. To add clients, click Add Clients. To manually assign an IP address, enter the client’s name in the Enter Client Name field. Enter an IP address in the Assign IP Address field.
Router Setup Advanced Routing NAT Setup The Network Address Translation (NAT) service is a standard that allows multiple computers on a private network to share a single IP address. RIP The Routing Information Protocol (RIP) helps the Router dynamically adapt to changes of network connections by communicating information about which networks each Router can reach and how far away those networks are. Static Routing This section allows you to define fixed routes to defined destinations.
Router Setup Destination LAN IP: Enter the Destination IP address that will be assigned to a specific network or host. Subnet Mask: Enter the subnet mask associated with the Destination IP. Gateway: This is the IP address of the gateway device that allows for contact between the Router and the remote network or host. Interface: This interface tells you whether the Destination IP Address is on the LAN & Wireless (Ethernet and wireless networks) or the WAN (Internet).
WiFi Setup WiFi Setup Basic WiFi Network Basic WiFi Setting Network Mode: From this drop-down menu, you can select the wireless standards running on your network. If you have both 802.11g and 802.11b devices in your network, keep the default setting, Mixed. If you have only 802.11g devices, select Wireless-G Only. If you have only 802.11b devices, select Wireless-B Only. If you do not want to use any WiFi network, select Disabled.
WiFi Setup WiFi Security WiFi Security Setting R100 provides several different levels of security to protect your WiFi network. Select a level in the Security Mode drop-down menu. WEP The Router supports two WEP (Wired Equivalent Privacy) standards: 64-bit and 128-bit. Select a standard from the drop-down list. The 64-bits encryption requires 10 hexadecimal digits (letters a-f and numbers 0-9 are valid). The 128-bits encryption requires 26 hexadecimal digits (letters a-f and numbers 0-9 are valid).
WiFi Setup TKIP and AES, with dynamic keys.
WiFi Setup WPA-Personal Encryption: Choose TKIP or AES from the drop down list. (AES is a stronger encryption method than TKIP.) Passphrase: Enter a passphrase between 8-63 characters. Key Renewal: Enter a key renewal value to tell the Router how often it should change the encryption keys. The value must be between 60-99999. WPA2-Personal WPA2 is a more advanced, more secure version of WPA. Encryption: Choose AES, or WPA-TKIP, or WPA2-AES from the drop down list.
WiFi Setup WPA-Enterprise This option features WPA used in coordination with a RADIUS server. (This should only be used when a RADIUS server is connected to the Router.) Encryption: Choose TKIP or AES from the drop down list. (AES is a stronger encryption method than TKIP.) RADIUS Server: Enter the IP Address of the RADIUS server. RADIUS Port: Enter the port number of the RADIUS server. The default value is 1812. Shared Key: Enter the key shared between the Router and the server.
WiFi Setup down list. RADIUS Server: Enter the IP Address of the RADIUS server. RADIUS Port: Enter the port number of the RADIUS server. The default value is 1812. Shared Key: Enter the key shared between the Router and the server. Key Renewal: Enter a key renewal value to tell the Router how often it should change the encryption keys. The value must be between 60-99999. RADIUS RADIUS stands for Remote Authentication Dial-In User Service.
WiFi Setup Disabled If you do not want to use any security method for your wireless network, choose Disabled. Advanced WiFi Setting AP Isolation: This isolates all wireless clients and wireless devices on your network from each other. Wireless devices will be able to communicate with the Router but not with each other. Frame Burst: Enabling this option may provide your network with greater performance.
WiFi Setup Transmission Rate: The rate of data transmission should be set depending on the speed of your wireless network. You can select from a range of transmission speeds. CTS Protection Mode: CTS (Clear To Send) is a function used to minimize collisions among wireless devices on a wireless local area network (LAN).
WiFi Setup WiFi Clients Filter WiFi Clients Filter You can allow or deny specific users to access your wireless network by using the WiFi Clients Filter. Service: To use the WiFi Clients Filter, select Enabled. To disable it, select Disabled. Filtering By: You can filter users by two methods: Prevent the listed PCs from accessing the wireless network, or Permit the listed PCs to access the wireless network. Select the method you want.
3.5G HSPA Setup 3.5G HSPA Setup PIN Verification After the Router is connected to the HSDPA ExpressCard, if your SIM card PIN protection is enabled, you must enter the PIN code for verification. Enter the code in the PIN Code field, and click Verify. PIN Management U/SIM's PIN Management After your SIM card is verified, you can enable or disable the PIN protection on your SIM card. Select Enabled or Disabled, and click Apply.
3.5G HSPA Setup U/SIM's Change PIN You can change the PIN code on the SIM card. Enter your original PIN code in the Old PIN Code field, enter the new PIN code in the New PIN Code field and the New PIN Confirm field, and click Change. Preferred Network Preferred Network Network Type: In the drop-down menu, select the network type your SIM card supports. If you do not know the network type, select Auto.
3.5G HSPA Setup Network Selection To select the mobile network operator automatically, in the Select Network field, select Auto. To select the operator from a list, select Manual and click Rescan. The list is displayed below. Select the mobile network operator you are currently using on your SIM card.
Security Setup Security Setup Firewall Firewall This tab is used to configure a firewall that filters out various types of unwanted traffic on the Router’s local network. SPI Firewall Protection The SPI (stateful packet inspection) firewall is programmed to recognize legitimate packets for different types of connections. Only packets matching a known connection state will be allowed by the firewall; others will be rejected.
Security Setup Filter Internet NAT Redirection: To use port forwarding to block access to local servers from local networked computers, select Filter Internet NAT Redirection. Filter IDENT (Port 113): This feature keeps port 113 from being scanned by devices outside of your local network. Web filter services Using the Web Filters feature, you may enable up to four specific filtering methods. Proxy: Use of WAN proxy servers may compromise the Router's security.
Security Setup Internet Access Policy Access can be managed by a policy. Use the settings on this screen to establish and access policies. To display a policy’s settings, select the policy from the drop-down menu. To delete a policy, select the policy’s number and click Delete This Policy. To view all the policies, click Summary. To delete multiple policies, in the Summary screen, selecting the policies and click Delete).
Security Setup To create an Internet access policy: 1. Select a number from the Access Policy dropdown menu. 2. Enter a policy name in the field provided. 3. To enable the policy, select Enabled. 4. To select which PCs are affected by the policy, click Edit List. The List of PCs screen appears. You can select a PC by MAC Address or IP Address. You can also enter a range of IP Addresses if you want the policy to affect a group of PCs.
Security Setup and Protocol fileds, and click Add. Single Port Forward Single Port Forwarding Port Forwarding allows you to set up public services on your network, such as web servers, ftp servers, e-mail servers, and other specialized Internet applications. To forward a port, enter the information in each field. Application Name: You can select an application from the 10 preset applications in the drop-down menu. For custom applications, enter the name of your application in one of the available fields.
Security Setup specific application. Enabled: To enable port forwarding for the application, select Enabled. To apply the changes, click Save Settings. Port Range Forward Port Range Forwarding Port Range Forwarding allows you to set up public services on your network, such as web servers, ftp servers, e-mail servers, and other specialized Internet applications. Application Name: Enter the name of your application.
Security Setup Port Range Trigger Port Range Triggering This feature allows the Router to watch outgoing data for specific port numbers. The Router remembers the IP address of the computer that sends the matching data, so that when the requested data returns through the Router, the data is pulled back to the proper computer by way of IP address and port mapping rules. Application Name: Enter the application name of the trigger. Triggered Range: For each application, enter the triggered port number range.
Security Setup QoS QoS Control Quality of service is the ability to provide different priorities to different applications, users, or data flows, or to guarantee a certain level of performance to a data flow. Wireless WMM Support: If no devices on your network support WMM, select Disabled. Otherwise, keep the default, Enabled. No Acknowledgement: If the Router’s Acknowledgement feature is disabled, the Router will not re-send data if an error occurs, then keep the default, Disabled.
Security Setup 1. Select the appropriate online games or applications. 2. Select the appropriate priority: High, Medium, Normal, or Low. 3. Click Add to save your changes. To add a new online games or applications: 1. Select Add a New Game/Application. 2. Enter any name to indicate the name of the entry. 3. Enter the port range that the application will be using. You can have up to three ranges to define for this bandwidth allocation. Port numbers can range from 1 to 65535. 4.
Administration Setup Administration Setup Management Router Access You can change the Router’s password here. Enter the password you want to set in the Router Password field, and re-enter it in the Re-Enter to confirm field. Then click Save Settings. Web Access Web Utility Access: HTTP (HyperText Transport Protocol) is the communications protocol used to connect to servers on the World Wide Web. HTTPs uses SSL (Secured Socket Layer) to encrypt data transmitted for higher security.
Administration Setup setting, you are only able to access the web-based utility via a wired connection. Remote Access Remote Management: To access the Router remotely, from outside the network, select Enabled. Web Utility Access: Choose to access the Router via HTTP or HTTPs. Remote Upgrade: To enable remote upgrade of the Router, select Enabled. Allow Remote IP Address: To allow any IP address to access to access the Router, select Any IP Address.
Administration Setup Diagnosis Log The Router can keep logs of all traffic for your Internet connection. To monitor the network, select Enabled. You can view logs by clicking View Log. If you want to view logs in a browser, enter an IP address in the Logviewer IP Address field. You can enter this IP in a browser to view logs.
Administration Setup Recover & Renewal Backup and Restore Backup Configurations Click Backup Configurations to back up your Router's current configuration. In the file dialog box, select a location and file name for the configuration file. Restore Configurations Click the Restore Configurations. In the file dialog box, click Browse to locate the configuration file, and click Restore. Factory Defaults To reset the Router's configuration settings to the default values, click Restore Factory Default.
Administration Setup dialog box, click Start. Router Upgrade To upgrade the Router's firmware, click Browse and locate the latest firmware upgrade file. After the file is located, click Start Upgrade. The upgrade progress is displayed. You can download the latest firmware from www.bandluxe.com. ; 45 Warning: Upgrading firmware may take a few minutes; do not turn off the power or press the Reset button during upgrade.
Status Status 3.5G HSPA & Internet Signal Quality When you access the Internet via 3G or 3.5G, click Refresh to show the signal strength. U/SIM Status Your SIM card verification status is shown in this area. Clicking Pin unlock displays the PIN Verification tab. Register Network Network Name: This shows the name of your network operator. Network Technology: This shows the network technology you are currently using.
Status Roaming status. Internet Connection Connection Type: This indicates the type of Internet connection you are using. Internet IP Address: This is the Router's IP Address, as seen on your local network. Subnet Mask and Default Gateway: The Router’s Subnet Mask and Default Gateway address are displayed here for DHCP and static IP connections. DNS1-3: The DNS (Domain Name System) IP addresses currently used by the Router are shown here.
Status Local Network Local MAC Address: This is the Router’s MAC Address, as seen by your ISP Router IP Address: The Router’s IP Address that appears on your local network. Subnet Mask: This shows the current subnet mask being configured for your local network. DHCP Server: The status of the DHCP server function is displayed here. Start IP Address: This shows the beginning of the range of IP Addresses used by devices on your local Ethernet network.
Appendix A: Specification Appendix A: Specification Form Factor Dimension (L x W x H, mm) 153 x 103 x 24 mm Weight (g) 160g typical Interface ExpressCard/34 interface for HSPA data modem Supported ExpressCard / USB interface switch Manual switch Wireless SecureEasySetup Button Yes LAN port RJ45, 1 port WAN port RJ45, 1 port Power plug Yes Reset button Yes Connectivity and Data Speed WLAN 802.11b/g LAN Ethernet Antenna WiFi Antenna 49 2 embedded antenna @ 2.4-2.
Appendix A: Specification Protocol Default connection "3.
Appendix A: Specification Accessories Power adaptor Supported Power Consumption Voltage 12V DC Current 1A max.
Appendix B: Important Safety Information and Glossary Appendix B: Important Safety Information and Glossary Europe – EU Declaration of Conformity This device complies with the essential requirements of the R&TTE Directive 1999/5/EC.
Appendix B: Important Safety Information and Glossary 2454 – 2483.5 MHz. For detailed information the end-user should contact the national spectrum authority in France.
Appendix B: Important Safety Information and Glossary Malti [Maltese] Magyar [Hungarian] Polski [Polish] Português [Portuguese] Slovensko [Slovenian] Slovensky [Slovak] Suomi [Finnish] Svenska [Swedish] Hawnhekk, [isem tal-manifattur], jiddikjara li dan [il-mudel tal-prodott] jikkonforma mal-ħtiġijiet essenzjali u ma provvedimenti oħrajn relevanti li hemm fid-Dirrettiva 1999/5/EC. Alulírott, [gyártó neve] nyilatkozom, hogy a [...
Appendix B: Important Safety Information and Glossary FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Appendix B: Important Safety Information and Glossary Glossary 2G: Second-generation mobile networking technology. Represents a switchover from analog to digital; most 2G networks use GSM. 3G: Third-generation mobile networking technology that enables simultaneous transfer of voice and non-voice data; most 3G networks use WCDMA. 3.5G: A more recent standard of mobile networking technology; generally uses HSDPA. APN (Access Point Name/Network): Provides GPRS routing information.
Appendix B: Important Safety Information and Glossary PIN (Personal Identity Number): Four to eight digital numbers SIM card security code; allows access to the carrier’s network. Rx: Shorthand for Reception. SIM (Subscriber Identity Module): A small card that contains key mobile device identification, subscription and contact information. SMS (Short Messaging Service): Allows text messages of up to 160 characters. Tx: Shorthand for Transmission.
