FCC ID: 2AG32MBS3100190 LTE Base Station mBS31001 Installation Guide 01 All rights reserved © Baicells Technologies Co., Ltd.
LTE TDD Base Station Installation Guide About This Document This document is a guidance of mBS31001 hardware installation for installation personnels, including the preparation of installation tools and supporting materials, the demands for installation environment, installation procedure, cable connection and power on.
LTE TDD Base Station Installation Guide Table of Contents 1. 2. 3. Product Overview ......................................................................................................... 1 1.1 Introduction ........................................................................................................... 1 1.2 Features ................................................................................................................. 1 1.3 Appearance .......................................
LTE TDD Base Station Installation Guide 3.6.2 Connect RF Cable .......................................................................................... 14 3.6.3 Connect Power Connector ............................................................................. 15 3.6.4 Connect Ground Cable .................................................................................. 16 3.7 Antenna Feeder System.............................................................................. 16 Install 4. 3.
LTE TDD Base Station Installation Guide 1. Product Overview 1.1 Introduction mBS31001 is a high performance outdoor micro base station based on LTE TDD technology, which is developed by Baicells. The mBS31001supports wired backhaul connections to backbone networks, and provides LTE access to user terminals, implemented voice and data service transmissions.
LTE TDD Base Station Installation Guide 1.3 Appearance The mBS31001 base station appearance is shown in Figure 1-1. Figure 1-1 Nova-436Q Appearance The mBS31001 interfaces and indicators are shown in Figure 1-2.
LTE TDD Base Station Installation Guide The mBS31001 interfaces are described in Table 1-1. The mBS31001 interface indicators are described in Table 1-1. Table 1-1 mBS31001 Interface Indicators Identity PWR Green CELL2 Green CELL1 Green ALM 1.4 Color Red Status Description Steady On Power On OFF No Power Supply Fast flash: 0.125s on,0.125s off CELL 2 inactivated Slow flash: 1s on,1s off CELL 2 activated Fast flash: 0.125s on,0.
LTE TDD Base Station Installation Guide Item Description Receive Sensitivity -100 dBm Backhaul 1 Optical (SFP) and 1 RJ-45 Ethernet interface (1 GE) MIMO DL 2 x 2 on each carrier Dimension 310mm(H) x 239 mm(W) x 105 mm(D) Installation Type Pole, wall Antenna External high gain antenna Overall Power < 60 W Power 48V DC, AC adaptor (multi-national standards) Weight About 5.5kg Note: The test method of receiving sensitivity is proposed by the 3GPP TS 36.
LTE TDD Base Station Installation Guide Item Description MTBF ≥ 150000 hours MTTR ≤ 1 hour Support remote/local maintenance, based on SSH protocol Support remote maintenance Support online status management Support performance statistics Support failure management Support configuration management Support local or remote software upgrading and loading Maintenance Support log Support connectivity diagnosis Support automatic start and configuration Support alarm reporting Support KPI Recording Support u
LTE TDD Base Station Installation Guide This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
LTE TDD Base Station Installation Guide 2. Installation Preparation 2.1 Support Materials Prepare the following support materials accordingly, as given in Table 2-1. Table 2-1 Support Materials for Installing Base Station Item Description Power cable < AWG16 e.g.
LTE TDD Base Station Installation Guide 2.3 Installation Environment 2.3.1 Locational Requirements Environments with high-temperatures, harmful gases, unstable voltages, volatile vibrations, loud noises, flames, explosives, and electromagnetic interference (large radar stations, transmitting stations, transformer substations) are not suitable for the operation of mBS31001, and thus should be avoided. Places prone to have impounded water, soaking, leakage, or condensation, should also be avoided.
LTE TDD Base Station Installation Guide Grounding Notes: The ground wire adopts yellow-green wire that is no smaller than 16 mm². Grounding principle: as near as possible. The base station connects to the reliable outdoor grounding point (earth) through one ground screw. The connection of the grounding points and the ground bar need to be tight and reliable. Rustproofing the terminals is required. This can be done with rust preventing paint, anti-oxidation coatings, grease, and so on. 2.
LTE TDD Base Station Installation Guide 3. As the following figure, hung the two pins on the base station bracket to the installation bracket, push the base station until the hook block to the base station bracket. 4. Tighten two screws on the top of the bracket using cross screwdriver to complete the installation.
LTE TDD Base Station Installation Guide 3.5 Install on Wall The wall must bear four times of the base station weight. 1. Take apart the assembled installation bracket kit to get the installation bracket 2. Fit the installation bracket on the wall, and mark the drilling locations. Caution: The arrow of the installation bracket must be upward. 3. Drill two 10mm diameter and 70mm depth holes in the wall by following the marked locations. 4.
LTE TDD Base Station Installation Guide 3. Lay optical fibers along the wire groove, and stretch out the wiring cavity from OPT hole. The redundant fiber should wind neatly. 3.6.2 Connect Ethernet Cable 1. Connect the Ethernet cable to ETH interface in the wiring cavity. 2. Lay Ethernet cable along the wire groove, and stretch out the wiring cavity from ETH hole. 3.6.
LTE TDD Base Station Installation Guide 6. If the outlet is outdoors, place the power adaptor in a water proof box. After the cable connection is complete in the wiring cavity, tighten the screws on the cover to close the wiring cavity using M4 cross screwdriver. 3.6.4 Connect Ground Cable Make the grounding cable according the actual situation of the installation site. The Nova-436Q provides two grounding screws, which is located on the bottom of the base station, as shown in Figure 3-3.
LTE TDD Base Station Installation Guide Make sure that the top of pole and the clamp beneath the antenna are at the same level, after installing the omnidirectional outdoor antenna on the pole. Make sure that the antenna is high enough to meet the coverage requirement, and that the antenna top falls within the 45 degrees safety angle towards the lightening rod, as shown in Figure 3-4.
LTE TDD Base Station Installation Guide Figure 3-5 Omnidirectional Antenna Installation (2) 3.7.2 Install Directional Antennas 1. First, assemble the antennas, as shown in Figure 3-6. Figure 3-6 Assembling Procedure of Directional Antennas 2. To install it on the iron tower, use a pulley to transport the antenna assembled to the platform on the iron tower, as shown in Figure 3-7. Following the safety rules when working at these heights.
LTE TDD Base Station Installation Guide Figure 3-7 Transportation the Antennas in the Height 3. Fix the pole vertically to the ground or concrete pillars on the rooftop using expansion screws, and fasten it with steel wires. Then, mount the directional outdoor antenna onto the pole using the installation rack, as shown in Figure 3-8. Figure 3-8 Directional Antenna Installation 4. When the base station has been installed in a proper position, connect all the cables and wires. 5.
LTE TDD Base Station Installation Guide 4. Power On Power on the Nova-436Q, and the indicators will light up, as shown in Figure 4-1. Figure 4-1 LED Indicators The explanation of the indicator signal is given in Table 4-1. Table 4-1 Nova-436Q Indicator Description Identity PWR CELL2 Color Green Green Status Description Steady On Power On OFF No Power Supply Fast flash: 0.125s on,0.125s off CELL 2 inactivated Slow flash: 1s on,1s off CELL 2 activated CELL1 Green Fast flash: 0.125s on,0.
Caution: This device complies with Part 15 of the FCC rules and Industry Canada license‐exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications or change to this equipment.
