LTE Turbo UE Configuration Guide for EG8015Q-M11 Document Version: 01 All rights reserved © Baicells Technologies Co., Ltd.
About This Document This document describes the configuration of the LteTurbo CPE for EG8015Q-M11. It is a guide that how to configure the device after its installation completes. Copyright Notice Baicells Technologies Co., Ltd., copyrights the information in this document. No part of this document may be reproduced in any form or means without the prior written consent of Baicells Technologies Co., Ltd. Disclaimer The information in this document is subject to change at any time without notice.
Menu 1. 2. 3. 4. 5. 6. 7. Configuration Overview .............................................................................................. 1 Installation ................................................................................................................... 1 2.1 Part & Materials ........................................................................................................ 1 2.2 Led .........................................................................................
8. 7.2 General VPN ............................................................................................................. 16 7.3 OpenVPN .................................................................................................................. 17 System........................................................................................................................ 18 8.1 NTP .........................................................................................................
1. Configuration Overview The Baicells LteTurbo CPE is loaded with its own GUI for configuring its operating parameters. You can log in to the GUI either locally through the Local Maintenance Terminal (LMT), which is an Ethernet port, or remotely via IP address. You can also use the Baicells Operations Management Console (OMC) to configure the CPE; this document, however, focuses only on using the web GUI.
Power Cable 1 PoE Power Adaptor 1 You will need standard tools, Ethernet cable, ground wire, and RJ-45 connectors for installing and connecting the outdoor unit. 2.2 Led The CPE has 10 lights, divided into 6 groups according to the function: wifi signal light, lte signal light, power light, sim light, lan light, miu light (see figure below).
Wifi signal light Arc logo ，Three lights indicate wifi signal strength according to the number of lights, full light indicates strong signal; full out when not connected Lte signal light Vertical logo ， Three lights indicate lte signal intensity according to the number of lights, full light indicates strong signal; flash when not connected Power light The power light is bright, indicating that the power supply is normal, otherwise the power supply is abnormal Sim light Light on -> Insert th
Miu light Reserved Note: The status of the lamp is meaningless during the start-on process, and wait for the start-on (5 minutes) before checking the LED status.
3. Login Web Client 3.1 Web Client Environmental Requirements Table 3-1 describes the requirements on computer of the client. Table 3-1 Environmental Requirements of the Client Item Description CPU Above Intel Core 1GHz Memory Above 2G RAM Hard disk No less than 100 MB space available Operating system Screen resolution Above 1024 x 768 Browser Chrome 6 or higher 3.2 Microsoft: Windows XP, Windows Vista or Windows7 Mac: MacOSX10.
Figure 3-1 Internet Protocol Version (TCP/IPV4) Select either “Obtain an IP address automatically” or “Use the following IP address”: If “Obtain an IP address automatically” selected, go directly to step 7 If “Use the following IP address” selected, follow step 5 ~ step 7 NOTE: In general, if the auto obtaining fails, one needs to set up the IP address manually. 5. Select “Use the following IP address”. 6. Input IP address, subnet mask, and default gateway, and then click “OK”. IP address: 192.
3.4 1. Log In Open a web browser, and enter http://192.168.150.1, as shown in Figure 3-1. Figure 3-1 GUI Login 2. Input user name, password, and click “Login”. The homepage is given in Figure 3-2. Default user/password : admin/admin Figure 3-2 GUI Homepage NOTE: The information may vary by product type or software version. The front page shows the information as the basic information and status information of the LteTurbo CPE.The status information is dynamically refreshed, refreshed every 3 seconds.
The status information area displays the WLAN connection status, rate statistics, LAN port connection status, and a list of connection devices.
4. Network Setting 4.1 LAN Settings Config Lan IP and DHCP params 4.
4.3 WLAN Settings Config wireless params, and wds switch. 4.
4.
5. LTE Setting 5.1 Connection Mode Support AUTO, Manaual mode 5.2 Scan Mode Support full band, fix pci, fix channel for lte scan. 5.
5.
6. Security Setting 6.1 Zones 6.
6.3 Traffic Rules 6.
7. VPN Setting 7.1 IPSec 7.
7.
8. System 8.1 NTP 8.
8.3 Dynamic DNS 8.
8.5 TR069 8.
8.7 SNMP 8.
8.9 Ping Watchdog 8.
8.11 SAS Setting 8.
8.13 Diagnosis 8.
9. Regulatory Compliance FCC Compliance This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
