Baicells mBS1105 Base Station Installation Guide V100R001C00 01 All rights reserved © Baicells Technologies Co., Ltd.
Baicells mBS1105 Base Station Installation Guide(V100R001C00,02).docx About This Document This document is a guidance of mBS1105 hardware installation for installation personnel, which includes the preparation of installation tools and supporting materials before installation, the demands of installation environment, installation of base station, connection of cable and power on.
Baicells mBS1105 Base Station Installation Guide(V100R001C00,02).docx Contents 1. 2. 3. 4. Product Overview ....................................................................................................... 1 1.1 Introduction ............................................................................................................... 1 1.2 Features...................................................................................................................... 1 1.3 Appearance .........
Baicells mBS1105 Base Station Installation Guide(V100R001C00,02).docx 4.6.2 Connect GPS Antenna ....................................................................................... 16 4.6.3 Connect RF Cable .............................................................................................. 17 4.6.4 Connect Optical Fiber ....................................................................................... 17 4.6.5 Connect Ethernet Cable ................................................
Baicells mBS1105 Base Station Installation Guide(V100R001C00,02).docx Figures Figure 1-1 mBS1105 Appearance ................................................................................ 2 Figure 1-2 mBS1105 Interfaces and Indicators ............................................................ 2 Figure 3-1 Installation Space Requirement .................................................................. 9 Figure 3-2 Antenna Weatherproofing ..................................................................
Baicells mBS1105 Base Station Installation Guide(V100R001C00,02).docx Tables Table 1-1 mBS1105 Interface Description .................................................................... 3 Table 1-2 mBS1105 Interface Indicators ...................................................................... 3 Table 2-1 Shipping List ................................................................................................. 6 Table 3-1 Support Materials for Installing Base Station ...............................
Baicells mBS1105 Base Station Installation Guide(V100R001C00,02).docx 1. Product Overview 1.1 Introduction Baicells mBS1105 is a high performance outdoor 3.65GHz micro base station based on TD-LTE technology, which is developed by Baicells. The mBS1105 supports wired backhaul connections to backbone networks, and provides LTE access to user terminals, implemented voice and data service transmissions.
Baicells mBS1105 Base Station Installation Guide(V100R001C00,02).docx 1.3 Appearance The mBS1105 base station appearance is shown in Figure 1-1. Figure 1-1 mBS1105 Appearance The mBS1105 interfaces and indicators are shown in Figure 1-2.
Baicells mBS1105 Base Station Installation Guide(V100R001C00,02).docx The mBS1105 interfaces are described in Table 1-1. Table 1-1 mBS1105 Interface Description Interface Name Description PWR Power interface: +48V (+42V~+60V) DC GPS External GPS antenna, N-female connector. ANT0 External antenna 0, N-female connector. OPT Optical interface, connect to external transmission network, used for data backhaul. ETH RJ-45 interface, used for debug or data backhaul.
Baicells mBS1105 Base Station Installation Guide(V100R001C00,02).docx Item Description Receiving sensitivity -102 dBm Synchronization Mode Backhaul Mode Optical and RJ-45 Ethernet backhaul MIMO 2*2MIMO Dimension 227mm (L) * 305mm (W) * 74mm (H) Installation Method Pole mounted, wall mounted Antenna External high gain antenna Overall Power < 50 W Power 48V DC Weight About 4.
Baicells mBS1105 Base Station Installation Guide(V100R001C00,02).docx Item Description Support online status management Support performance statistics Support failure management Support configuration management Support local or remote software upgrading and loading Support log Support connectivity diagnosis Support automatic start and configuration Support alarm reporting 1.4.
Baicells mBS1105 Base Station Installation Guide(V100R001C00,02).docx 2. Out-of-Box Audit Before opening the box, make sure the package is in good condition, undamaged and not wet. During the unpacking, avoid potential damaging impacts from hits or excessive force. Once unpacked, check the contents to see if they are consistent with that in the shipping list shown in Table 2-1.
Baicells mBS1105 Base Station Installation Guide(V100R001C00,02).docx 3. Installation Preparation 3.1 Support Materials Prepare the following support materials accordingly, as given in Table 3-1. Table 3-1 Support Materials for Installing Base Station Item Description Power cable < AWG16，e.g.
Baicells mBS1105 Base Station Installation Guide(V100R001C00,02).docx 3.3 Installation Environment 3.3.1 Locational Requirements Environments with high-temperatures, harmful gases, unstable voltages, volatile vibrations, loud noises, flames, explosives, and electromagnetic interference (large radar stations, transmitting stations, transformer substations) are not suitable for the operation of mBS1105, and thus should be avoided.
Baicells mBS1105 Base Station Installation Guide(V100R001C00,02).docx Figure 3-1 Installation Space Requirement 3.4 Personnel Requirements The installation personnel must master the basic safe operation knowledge, through the training, and having the corresponding qualifications.. 3.
Baicells mBS1105 Base Station Installation Guide(V100R001C00,02).docx The connection of the grounding points and the ground bar need to be tight and reliable. Rustproofing the terminals is required. This can be done with rust preventing paint, anti-oxidation coatings, grease, and so on. 3.6 1. Weatherproof Protection To weatherproof the connections, wrap them with all-weather electrical tape and mastic tape, as shown in Figure 3-2. Figure 3-2 Antenna Weatherproofing 2.
Baicells mBS1105 Base Station Installation Guide(V100R001C00,02).docx 4. Base Station Installation 4.1 Installation Procedure The installation procedure of mBS1105 is given in Figure 4-1. Figure 4-1 Installation Procedure of mBS1105 4.2 Install the Mounting Bracket and Handle Using the M6*16 hex screw to fix the bracket on back side of the mBS1105, as shown in Figure 4-2.
Baicells mBS1105 Base Station Installation Guide(V100R001C00,02).docx Figure 4-2 Install the Mounting Bracket Caution: The arrow of the installation bracket must be upward. 4.3 Install GPS Antenna Installation requirements on the GPS antenna: No major blocking from buildings in the vicinity. Keep the rooftop buildings a distance away from the GPS. Make sure the space atop within 90 degrees (at least 45 degrees) is not blocked by any buildings.
Baicells mBS1105 Base Station Installation Guide(V100R001C00,02).docx 2. Pass the GPS antenna through the hole on the GPS mounting bracket. 3. Installation is complete. 4.4 Install on Pole Required diameter of the pole: 40mm ~ 100mm. Suggest the installation height higher than 120cm, and the installation space requirements meet the requirements in “3.3.3Space Requirements”. 1. As the following figure, assemble the bracket for pole installation, and fasten the four nuts. .
Baicells mBS1105 Base Station Installation Guide(V100R001C00,02).docx 2. Make sure the installation height of the eNodeB, fit the thread rod of the assembled bracket to the pole, and then pass the omega through the threaded rods, and fasten the four nuts. Caution: The arrow of the installation bracket must be upward. 3. As the following figure, hung the two pin on the eNodeB bracket to the installation bracket, push the eNodeB until the hook block to the eNodeB bracket 4.
Baicells mBS1105 Base Station Installation Guide(V100R001C00,02).docx 4.5 Install on Wall The wall must bear four times of the eNodeB weight. 1. Fit the base station on the wall, and mark the drilling locations. Caution: The arrow of the installation bracket must be upward. 2. Drill four 10mm diameter and 70mm depth holes in the wall by following the marked locations. 3. Check the up/down direction of the installation rack, and then fix the eNodeB to the wall using M8*80 expansion screws. 4.
Baicells mBS1105 Base Station Installation Guide(V100R001C00,02).docx 6. The installation is complete. 4.6 Connect Cable 4.6.
Baicells mBS1105 Base Station Installation Guide(V100R001C00,02).docx 4.6.3 Connect RF Cable 1. Open the dust cap of ANT0 and ANT1 interface. 2. Connect one end of the RF cable to ANT0 and ANT1 interface of the eNodeB and fasten them with wrench. 3. Connect the other end of the RF cable to the external antenna. 4. It is necessary for ANT0 and ANT1 interfaces to be weatherproofed. Refer to 3.6 Weatherproof Protection for more detail. 4.6.4 Connect Optical Fiber 1.
Baicells mBS1105 Base Station Installation Guide(V100R001C00,02).docx 4. If the outlet is indoors, place the power adaptor indoors. If the outlet is outdoors, place the power adaptor in a water proof box. After the cable connection is complete in the wiring cavity, fasten the screws on the cover to close the wiring cavity using M4 cross screwdriver. 4.6.7 Connect Ground Cable Make the grounding cable according the actual situation of the installation site.
Baicells mBS1105 Base Station Installation Guide(V100R001C00,02).docx Make sure that the antenna is high enough to meet the coverage requirement, and that the antenna top falls within the 45 degrees safety angle towards the lightening rod, as shown in Figure 4-4. In principle, no lightening rod can be welded to pole (no metal object is allowed within 1m of the horizontal direction of the omnidirectional antennas), when installing the omnidirectional antennas.
Baicells mBS1105 Base Station Installation Guide(V100R001C00,02).docx Figure 4-5 Omnidirectional Antenna Installation (2) 4.7.2 Install Directional Antennas 1. First, assemble the antennas, as shown in Figure 4-6. Figure 4-6 Assembling Procedure of Directional Antennas 2. To install it on the iron tower, use a pulley to transport the antenna assembled to the platform on the iron tower, as shown in Figure 4-7. Following the safety rules when working at these heights.
Baicells mBS1105 Base Station Installation Guide(V100R001C00,02).docx Figure 4-7 Transportation the Antennas in the Height 3. Fix the pole vertically to the ground or concrete pillars on the rooftop using expansion screws, and fasten it with steel wires. Then, mount the directional outdoor antenna onto the pole using the installation rack, as shown in Figure 4-8. Figure 4-8 Directional Antenna Installation 4.
Baicells mBS1105 Base Station Installation Guide(V100R001C00,02).docx 5. Power On Power on the mBS1105, and the indicators will light up, as shown in Figure 5-1. Figure 5-1 LED Indicators The explanation of the indicator signal is given in Table 5-1. Table 5-1 mBS1105 Indicator Description Type PWR RUN ALM ACT Color Green Green Red Green Status Meaning ON Have power input OFF No power input Fast blink: 0.125s on, 0.
Baicells mBS1105 Base Station Installation Guide(V100R001C00,02).docx Appendix A Additional Information A.1 Antenna Information The following is a list of antennas that are certified for use. Customers can choose different antennas according to the environment. Table 5-2 Antenna Information Antenna Type Antenna Max Gain(dBi) Manufacturer Model Number External Planar Antenna Dual Pole Kenbotong Technology Co., Ltd. KBT90DP13-3338 AT0 13 External Planar Antenna Dual Pole Kenbotong Technology Co.
Baicells mBS1105 Base Station Installation Guide(V100R001C00,02).docx A.2 Maximum Output Power The maximum output power can be set as follows: Antenna Max Gain (dBi) 10Log(Number of antennas) Channel BW (MHz) Max output power (dBm) EIRP (dBm) 10 23 39 20 23 39 10 22 39 20 22 39 10 25 39 20 25 39 10 29 39 20 29 40 10 30 39 20 30 39 10 33 39 20 33 39 10 28 39 20 28 39 13 14 11 7 3 6 3 8 A.
Baicells mBS1105 Base Station Installation Guide(V100R001C00,02).docx digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
