BaiCells EG7035 User Manual V1.0 All rights reserved © BaiCells Technologies Co., Ltd.
About This Document This document introduces the specifications of BaiCells EG7035 CPE and guides users to install and configure it. Copyright Notice BaiCells copyrights this specification. No part of this specification may be reproduced in any form or means, without the prior written consent of BaiCells. Disclaimer This specification is preliminary and is subject to change at any time without notice. BaiCells assumes no responsibility for any errors contained herein.
Contents 1. 2. 3. Product Overview ....................................................................................................... 1 1.1 Introduction .............................................................................................................. 1 1.2 Features ..................................................................................................................... 1 1.3 Product Description............................................................................
A.1 The POWER indicator does not turn on. .................................................................. 14 A.2 Fails to Login to the web management page. .......................................................... 14 A.3 The CPE fails to search for the wireless network. .................................................... 14 A.4 The power adapter of the CPE is overheated. ......................................................... 14 A.5 The parameters are restored to default values. ............
Contents of Figure Figure 1-1 EG7035 Appearance .................................................................................. 2 Figure 1-2 Interface and Button of EG7035 ................................................................. 3 Figure 3-1 Install the Sample .......................................................................................... 8 Figure 3-2 Connection Diagram ...................................................................................... 8 Figure 4-1 Login Page .....
Contents of Table Table 1-1 EG7035 Product Description ........................................................................ 2 Table 1-2 EG7035 Appearance Index .......................................................................... 2 Table 1-3 Description of EG7035 Interface and Button ............................................... 3 Table 1-4 LED Indicators .............................................................................................. 3 Table 2-1 Basic Specification ................
1. Product Overview 1.1 Introduction Baicells is a high-tech company dedicated in wireless broadband access solutions and service operation. With the advent of the Internet+ era, the development of WBB is imminent. Through continuous innovation, Baicells launches the world first mobile broadband system based on the Internet architecture and unlicensed spectrum. Baicells can provide serious CPEs, include indoor and outdoor unit on different spectrums. Baicells EG7035 is a high performance outdoor CPE.
Protection support IP67. Support pole installation or wall mounting. 1.3 Product Description EG7035 CPE product is shown in Table 1-1. Table 1-1 EG7035 Product Description Product EG7035 1.4 Description 3.65G LTE Customer Premise Equipment Appearance The appearance of EG7035 is shown in Figure 1-1, and is described in Table 1-2.
1.5 Interface and Button The interface of EG7035 is shown in Figure 1-2, and is described in Table 1-3. Figure 1-2 Interface and Button of EG7035 Table 1-3 Description of EG7035 Interface and Button Connectors ETH RJ45 USIM Slot Restore Button 1.6 Description One LAN Support 1.8V/3.
2. Technical Specifications 2.1 Basic Specification Table 2-1 Basic Specification Specification LTE Standard Ethernet LAN Port LED Indicators USIM Restore Button Description 3GPP Release 9 One RJ-45 port 10/100 auto-sensing, auto-MDX, 12V ~ 24V PoE Power/LET Signal/LAN Indicator Support 1.8V/3.3V 2FF USIM Tact Button Power Supply 2.
SIM Network Connection setup LTE Scan Mode VPN NAT Statistics 2.
Table 2-5 Environment Specification Feature Operating Temperature Storage Temperature Operating Humidity Drop Protected Level 2.6 Capability -40℃ ~ 55℃ -40℃ ~ 70℃ 5% ~ 95% 0.8m IP67 Regulatory Compliance FCC Compliance This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Warning This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator & your body. IC Compliance This device complies with Industry Canada licence-exempt RSS standard(s).
3. Product Installation 1.1 Installation Steps 1. Assemble waterproof parts. Plug cable local connection, as shown in Figure 3-1. 2. Open the waterproof cover, and according to the instructions on the SIM card. 3. Connected to the adapter, Pay attention to the adapter interface identify. Figure 3-1 Install the Sample 4. Mount adapter, and electricity, you can see the LED turn light, as shown in Figure 3-1.
4. CPE Configuration 4.1 Log in By using a Web browser to login the CPE management page, the CPE configuration management. Log on to the Web management page steps are as follows: 1. Power on. 2. In the address column of browser, type in http://192.168.1.1, then press “Enter”, login in page is shown in Figure 4-1. Figure 4-1 Login Page 3. Enter the user name and password, click "Login" button. After password authentication, you can log on to the web management page.
Figure 4-2 Setup Network Mod 4.2.2 LTE Setting To set the LTE Network, perform the following steps: 1. Choose Network Setting>LTE Setting. 2. In the LTE Setting area, you can configure the LTE network. 3. In the LTE Setting area, you can also view the network information such as frequency, DL&UL MCS, RSRP, RSRQ, CINR, SINR, Tx Power, Cell ID, PCI, MCC and MNC.
4.2.3 Setting Connect Method To set the LTE network connect method, perform the following steps: 1. Choose Network Setting>LTE Setting. 2. In the LTE Setting area, you can set the connect method. 3. There are two methods to connect the LTE network, it is needed to choose a method between Auto and Manual, if you want to auto connect to the LET network you should choose the Auto, otherwise you should choose Manual. 4. Click “Submit”. Figure 4-4 Setup Connect Method 4.2.
4.2.5 Setting Scan Mode To set the LTE network scan mode, perform the following steps: 1. Choose Network Setting>LTE Setting. 2. In the LTE setting area, you can set the scan mode. 3. You can choose full Band, PCI Lock, or a band the CPE supported. Figure 4-5 Setup Scan Mode 4.2.6 Setting Frequency (Earfcn) To set the frequency, perform the following steps: 1. Choose Network Setting>LTE Setting. 2. In the LTE setting area, click to set the frequency. 3.
Figure 4-6 Setting frequency 4.2.7 APN Management 1. To set and manage APN, perform the following steps: 2. Choose Network Setting>APN Management. 3. In the APN Management area, you can set the APN. 4. Choose an APN number which you want to set. 5. In the APN Setting area you can set the APN parameters, such as enable or disable the APN, APN name, username, password and so on. 6. If you want set an APN as default gateway, you should check that is enabled. 7. Click “Submit”.
Appendix A FAQs A.1 The POWER indicator does not turn on. Make sure that the power cable is connected properly and the CPE is powered on. Make sure that the power adapter is compatible with the CPE. A.2 Fails to Login to the web management page. Make sure that the CPE is started. Verify that the CPE is correctly connected to the computer through a network cable. If the problem persists, contact authorized local service suppliers. A.3 The CPE fails to search for the wireless network.
Appendix B Product List Index Content 1 EG7035 CPE Picture Amount 1 2 12V/1A adapter 1 3 PoE Combiner 1 4 Mounting bracket 1 5 User Manual n/a 1 15
BaiCells EG7035 Bracket Installation Guide V1.0 All rights reserved © BaiCells Technologies Co., Ltd.
Assemble Bracket 1 Install bracket and screw on, do not tighten the screws. 2 Install ground wire and lock the screw. 3 Tighten four screws using allen hexagon wrench. 4 Put U shape screw on bracket of lock wall and install it on CPE bracket. 5 Screw on four bacaket srews.
Install on Pole 1 Loop U shape screw on pole and put on pole bracket. 3 Adjust CPE to a suitble position. 4 Tighten four screws. 2 Tighten U shape screw nut using wrench.
