ORION® SE Trimble® Ranger™ Handheld IMPORTANT: This manual contains important information. READ AND KEEP FOR REFERENCE.
Trimble® Ranger™ Page ii 1-11
Installation & Operation Manual CONTENTS Introduction............................................................................................................................................. 7 About This Manual.................................................................................................................................. 7 LICENSE REQUIREMENTS........................................................................................................................ 7 Manual Organization..
Trimble® Ranger™ Detailed Operations................................................................................................................................ 19 The Reading Cycle................................................................................................................................................................. 19 Restarting the Unit..............................................................................................................................................
Installation & Operation Manual Advancing the Display......................................................................................................................................................... 36 Error Conditions – Stopped Meters and Reverse Flow....................................................................................................... 36 Other Reading functions – The Reading Menu.......................................................................................................
Trimble® Ranger™ Reading the Transmitter Through the Optical Port........................................................................................................... 66 Starting the Badger Meter ORION® Transmitter without the Programmer..................................................................... 66 Using the Programmer to start a Transmitter.................................................................................................................... 67 Stopping a Transmitter..........
Installation & Operation Manual Introduction The Trimble® Ranger™ handheld computer is a flexible and easy-to-use tool, which can be used with various meter reading technologies. It provides utilities with a handheld interrogator that can be operated with a customized keypad for data entry. The Trimble handheld can gather and accept: • Meter readings from meters equipped with Badger Meter ORION® and Badger Meter GALAXY® endpoints. • Meter readings that are visually read and manually entered.
Trimble® Ranger™ The following Hot Keys can be pressed to make finding and bookmarking of accounts easier for the operator: Read Screen Key Assoc. Hot Key On-screen usage A -- Auto-mode -- Assoc. Hot Key (double/single-tap) B BOOKMARK C -- Toggle Bookmark Next Bookmark D RD DIRECT Toggle route reading direction. E RESEQ Resequence (unimplemented) F RTSTART Route Start G -- H HI/LO I -- View High/Low reads for current account.
Installation & Operation Manual Manual Organization The manual is divided into these sections: • Introduction • Glossary • The Makeup of the Trimble Ranger • Detailed Operations • What If Things Go Wrong The Glossary section will provide definitions of the terminology for automatic meter reading. The “Makeup of the Trimble Ranger” section describes all pertinent features. The “Detailed Operations” describes Trimble Ranger functions.
Trimble® Ranger™ GLOSSARY The following is common Trimble Ranger terminology. TERM DEFINITION BadgerTouch® Badger Meter’s touch product. Comment code A comment code is a message from the office to the meter reader that is displayed as soon as the meter is displayed on the read screen. The possible messages are defined and maintained by the user in Badger Meter Reading Data Management Software and chosen from the defined list.
Installation & Operation Manual TERM DEFINITION Send readings The function that prepares gathered meter readings and transfers them to the Badger Meter Reading Data Management Software. Service The type of utility being measured by the meter, for example Water, Gas or Electric. Settings The values that can be changed by the user to control behavior to certain functions.
Trimble® Ranger™ THE MAKEUP OF THE TRIMBLE RANGER The Trimble Ranger is made up of a number of functions that all work together to perform meter reading quickly and easily. Review the following section to familiarize yourself with the hardware that makes up the Trimble Ranger..
Installation & Operation Manual Unit Setup Charge the PowerBoot Module The PowerBoot Module™ that contains the batteries is shipped detached from the unit. Before operating the Trimble Ranger, the PowerBoot should be charged. The AC charger that ships with your unit has adapters to fit most electrical outlets. Connect the appropriate outlet adapter to the AC charger. Plug the charger into an electrical outlet and plug the barrel end of the charger into the PowerBoot.
Trimble® Ranger™ Applying and Removing Power To turn the unit on, press and release the green Power key on the lower left hand corner of the keypad. To turn the unit off, press and release the Power key again. One of the most convenient features of the unit is “instant on” and “instant off” (also known as “suspend/resume”). There is no waiting for the unit to boot up every time it is turned on. “Instant on” does not occur on the first boot-up.
Installation & Operation Manual PowerBoot Module The PowerBoot includes the batteries to power the unit, the power port used to charge the unit, and the I/O ports that are used to communicate with other devices using a USB or serial cable. Battery life The Trimble Ranger has been designed to operate with the internal BlueTooth® and 802.11 wireless communication features and will automatically turn them off when not in use. Do not turn these wireless features on unless instructed.
Trimble® Ranger™ Swapping the PowerBoot Module The PowerBoot is designed to be quickly swapped in the field (if you have purchased additional PowerBoot Modules). If the current PowerBoot Module runs low, replace it and continue with your w ork. The unit saves enough power that if you swap the PowerBoot within a couple of minutes, it will not trigger a reset. If the saved power runs out before the new PowerBoot is connected, the unit will reset.
Installation & Operation Manual Accessing Storage Memory using File Explorer File Explorer (Start / Programs / File Explorer) allows browsing of the contents of folders on your unit. To easily delete, rename, or copy an item, touch and hold the item. NOTE: Unlike desktop PCs, Windows Mobile® 5.0 does not support a Recycle Bin. Once a file is deleted, it cannot be recovered.
Trimble® Ranger™ Date & Time Setting During training, the Trimble Ranger will be started and the initial settings will be completed by your trainer. These initial settings include setting the time, the date, the time zone, and the unit’s name. Each Trimble Ranger will have a unique name to make loading and unloading easier. To update the time or date, use the Date function in Windows Mobile, accessed by clicking Start / Settings / Clocks and Alarms.
Installation & Operation Manual Detailed Operations The Reading Cycle Using the Trimble Ranger for meter reading is easy. The reading cycle consists of these steps: 1. From Badger Meter Reading Data Management Software, use the Load Collector function to send the meter information. 2. From the Main Menu of the Trimble Ranger press the “R” key to begin the meter reading. 3.
Trimble® Ranger™ You may also tap on any colored title bar at any time and see a temporary popup information bar detailing the current battery status: Copyright Screen The Copyright screen is the starting point for the route reading program. From here, you can: • View the route reading program name, version, and copyright information • View the Trimble Ranger’s “Friendly Name” -- Every Trimble Ranger is assigned a globally unique name (GUID) consisting of an excessive number of characters.
Installation & Operation Manual • Trademarks “T” button : Will display the list of Trademarks referenced in this program. • Continue “ENTER” button : Pressing the Continue button or pressing the ENTER key on your Trimble Ranger keyboard brings you to the Main Menu. • “Exit” LEFT Soft Menu key : Exits the program. • “View ID” RIGHT Soft Menu key : takes you to the Device “Friendly Name” editing screen, where you can also view the Trimble Ranger’s GUID.
Trimble® Ranger™ Device ID/Name screen From the Copyright screen, press the “View ID” RIGHT Soft Menu key to display the Device ID/Name screen: • “Close” LEFT Soft Menu key : closes this screen • “Change Name” RIGHT Soft Menu key : allows you to edit/change your Trimble Ranger’s “Friendly Name” Select the “Change Name” RIGHT Soft Menu key, the screen changes to look like this: • Clear button : tapping the Clear button will erase all characters in the “New” “Friendly Name” field.
Installation & Operation Manual ReadCenter Main Menu Press the Continue button on the Copyright screen to see the Main Menu. There are five functions on the main menu to choose from. These options can be selected by using the Stylus to tap the box containing the desired function or by pressing the appropriate underlined alpha character on the keyboard: • Read Route “R” – Begin reading meters • Program and Quick Read “Q” – Use the Trimble Ranger to read meters when you do not have any loaded (i.e.
Trimble® Ranger™ Route Info screen • Route File– The name/number of the route • Route File Time – The time of the last captured reading • Last download – The time when this route was transferred from the PC • Last upload file – The time the previous route was transferred to the PC For more details, see the Route Operations portion of the Details section. To return to the Route Transfer screen, select the “Close” LEFT Soft Menu key, or press your Trimble Ranger’s ENTER key.
Installation & Operation Manual Meter Reading Log In screen The bottom of the screen shows the function of the two application-specific soft keys in the top row of the keypad (just under the screen). Their function conforms to the needs of the program that is currently running. The Log In screen accepts your 3 to 5 character personal ID (PIN). Your PIN can be your name, your initials, an ID number, etc. When PIN is entered, the screen looks like this.
Trimble® Ranger™ If a valid PIN is entered, the Trimble Ranger displays the Main Menu. If the PIN is not valid, the Trimble Ranger will indicate. Select the “Retry” LEFT Soft Menu key or press your Trimble Ranger’s ENTER key and reenter your PIN correctly to display the Main Menu. If you select the “Cancel” RIGHT Soft Menu key or press the “C” key on your Trimble Ranger, you will return to the Copyright screen. The Read Screen After successfully entering your Log In information, meter reading begins.
Installation & Operation Manual Navigation If the current meter is the first one in the route and you press the Previous Account button, the READCENTER® Software will ask you if you want to stay at the beginning of the route or if you wish to go to the end of the route. • Selecting the “No Stay” RIGHT Soft Menu key or pressing “N” key will keep you at the first meter in the route. • Selecting the “Yes Last” LEFT Soft Menu key or pressing the ENTER key will take you to the last meter in the route.
Trimble® Ranger™ Reading Meters The Read Screen shows specific information about the meter to be read including: • Meter information appears on the first five lines of the display. This information can be customized by the user through Badger Meter Reading Data Management Software. See the Badger Meter Reading Data Management Software manual for information on setting the account information loaded to the Trimble Ranger. • The sixth line will display user-customizable information.
Installation & Operation Manual Gathering Meter Readings The Trimble Ranger performs meter readings both automatically and manually. When in automatic mode, the handheld will accept Badger Meter ORION meter readings and store them in the proper account. The screen will display the next unread meter, or the meter that was last displayed on the screen. If a reading is received for the meter shown on the screen, the screen is updated with the next unread meter.
Trimble® Ranger™ Processing the ORION Meter Reading Once the Trimble Ranger has received a meter reading from a Badger Meter ORION endpoint, it processes the information in a number of steps: • Determines if the message from the endpoint was received correctly • Determines the tamper status, non-usage, reverse flow (ADE only), and potential leak status of the endpoint • Determines the reading value reported by the endpoint • Evaluates the reading value against the high and low audit values to determ
Installation & Operation Manual If you choose Trouble Code, the Trimble Ranger will return to the Tamper Menu screen once the code is entered and stored so that you can also enter a manual reading. If you choose to enter a Manual Read, you’ll see this screen: Enter the reading and press the “Enter” button or select the “OK” RIGHT Soft Menu key. If you wish to skip the manual read, select the “Cancel” LEFT Soft Menu key. When you have completed entries for this meter, press the ”OK” LEFT Soft Menu key.
Trimble® Ranger™ The previous screen is an Encoder Error reported by an ORION endpoint while the second picture is one reported by a Touch read. To process an Encoder Error, choose one of these options by pressing the corresponding button or by using the Stylus to tap the correct option on the screen. • “T” (Trouble Code) – Using this option you can enter a trouble code to report the status of the meter to the office. See the Trouble Code section for more details.
Installation & Operation Manual The read screen for manual mode looks like this: When in manual mode, the meter reader can enter readings for manually read meters or perform any other Trimble Ranger function such as searching for a particular meter or viewing progress. When the manual and touch-type meters have been read and the next meter to read is a Badger Meter ORION® endpoint, you can return to automatic mode by pressing the “A” key. This action will return the handheld to automatic meter reading.
Trimble® Ranger™ To change the direction of the meter reading, tap on the direction arrows (“>>”). The screen will display the direction of the reading by showing an arrow pointing to the left next to the reading field. When you enter a meter reading now, the reading will be shown on the display from right to left.
Installation & Operation Manual Here is what you will see if you enter a reading below the low limit. Select the “OK” LEFT Soft Menu key and the Trimble Ranger will display the read screen again. Re-enter the meter reading and press Enter. If the second meter reading matches the first meter reading, the Trimble Ranger records the reading and displays the next meter.
Trimble® Ranger™ If you’ve entered a low reading, you might see this screen: If the value shown is the correct value, select the “Yes” LEFT Soft Menu key. The reading will be accepted and stored. It will then advance to the next meter. If the value shown does not match the reading for this meter, press the No button on the screen. The handheld will return to the reading screen for this meter. Begin the meter reading process can then begin again.
Installation & Operation Manual When no consumption has occurred at a meter with an ADE, the ORION endpoint reports the condition and you’ll see a screen like this: You can enter a manual read or a trouble code. When you are finished with the entries for this meter, select the “OK” LEFT Soft Menu key. The read screen will look like this: The no usage indicator is at the bottom right corner of the screen.
Trimble® Ranger™ The settings to control these options are stored in the Utility Settings off of the Read Menu or Main Menu. • Pressing the “U” key or tapping in the box will turn the No usage check on and off. • Pressing the “R” key or tapping in the box will turn the Reverse Flow check on and off. If the No Usage check is turned on, and the manual reading for a meter is the same as the previous reading, you’ll see a screen like this.
Installation & Operation Manual If the Reverse Flow check is turned on, and the manual reading for a meter is lower than the previous reading, you’ll see a screen like this. Because the reading may be in error, you will be asked to verify the reading. • If the ”Hi/Low Entry Disposition” is set to “Reentry Required” or “Reentry w/Cancel,” you will be asked to enter the reading again. • If ”Accept/Reject” is selected, you will be asked if the reading is correct.
Trimble® Ranger™ to the original reading direction, choose this function again—it toggles between the two. • Comments “O”. Allows you to select Reader Codes, Trouble Codes, and to enter Text Message. • New Account “N”. New account creation. • Utilities “U”. Takes you to the Utilities menu, where you can view route reading progress, current battery state, and settings. • Erase Read “E”. Erases the current Account’s reading.
Installation & Operation Manual Search In addition to the “Hot Keys”, meter readers can also find a specific account through the Search Menu. When you are displaying a meter to read, press the menu button to display the Read Menu screen. From the reading menu, press “S” key or tap the box on the screen labeled “Search”. The screen will display the Search Menu. There are different ways to search for a particular meter.
Trimble® Ranger™ In our example, the five fields being used are name, address, meter number, AMR serial number, and route/sequence number. In addition, the account number and the AMR module number can also be searched. Click on the up arrow button to move the highlight field up and the down arrow button to move the field down. Next, enter the text via the keyboard for which you want to search in the Search Text field. In our example, we will search for a particular name.
Installation & Operation Manual If this is the meter you are looking for, tap the “Yes” button on the screen. If this is not the meter you are looking for, tap the “No” button on the screen and the search will continue. If you wish to stop the search, select the “Cancel” LEFT Soft Menu key and the reader will return to the Search Menu. If the meter cannot be found, you’ll see this screen. Searching for accounts using the other fields on the read screen works in exactly the same manner.
Trimble® Ranger™ To log a Trouble Code or one or more Reader Codes, touch the Comments button “O” or tap the Comments button on the screen using the Stylus from the Reading Menu. The Comments Menu will be displayed. From there you can choose the Trouble Code button “T” or the Reader Code button “R”, depending on which code you wish to use. In addition, the Trouble Code or Reader Code can be selected by tapping the appropriate box on the screen with the Stylus.
Installation & Operation Manual If the code you need is not on the screen, move the slider bar on the right up and down until you see the code, then touch the code to highlight it. Finally, select the “Select” RIGHT Soft Menu key to choose that code for the current meter. The screen will look like this. Select the “OK” RIGHT Soft Menu key to store the chosen trouble code and return to the Comment menu, or select the “Cancel” LEFT Soft Menu key to cancel any entry of a trouble code.
Trimble® Ranger™ To enter a Reader Code, select the number of the code (either 1, 2, or 3 on the keypad or by tapping the appropriate box on the screen) to display the choices for that code. You can select the “Cancel” LEFT Soft Menu key to cancel the entry of a reader code. Again, if you choose to clear a Reader Code entry, choose the blank line at the top of the list and press the “Enter” key. If you have chosen a message, you might see a screen like this.
Installation & Operation Manual Bookmark The bookmark function allows you to mark a particular meter in the route as one you might wish to revisit later. One common use of the bookmark function occurs when you come upon a flooded meter pit, and your pump is back in the truck. You can set a bookmark at this meter and continue reading. Later, once you have the pump, you can search for the meter(s) that is/are bookmarked, and return to them to continue your work.
Trimble® Ranger™ If a meter has a reading, you cannot enter a skip code. You will see this error screen. Similarly, if the meter is skipped, you cannot enter a reading without first clearing the skip code. Because the skip code is either a Trouble code or a Reader code, the search function can be used to find a specific skip code. This screen shows the case where a Skip codes are defined as a Trouble code.
Installation & Operation Manual To return the meter’s status to unread, press the “Z” or “ZZ” keys again while the skipped meter is displayed on the screen. Search by Route When searching, you can search for a particular route. When you tap Search, then Select route, you will see a screen similar to this: If a route is not completely read, you can mark it as completed by tapping the Mark as Complete button. If the route is already marked as completed, you can remove the mark by tapping the Remove button.
Trimble® Ranger™ Text Messages To enter a text message, press the text message “M” button. If no Text Message currently exists, you will automatically be taken to the Text Message screen in editing mode—you can begin typing immediately. To create a new text message for this meter, simply begin typing. To cancel the message, select the “Cancel” LEFT Soft Menu key.
Installation & Operation Manual When the message is entered, select the “Save” RIGHT Soft Menu key to complete the message. Viewing High and Low Audit Values If you wish to see the high and low audit values, the account number, or the previous reading, from the Read Menu press the View Hi/Lo button “V”. The screen will display the account number for the meter being read, and the high, low, and previous reading values for the meter (if passed from billing software).
Trimble® Ranger™ In some cases, the high, low, or previous readings may not be displayed. On the Settings screen in the Utilities section, there are two choices that control the display of this screen. The high and low audit values will be displayed if you have chosen the Show High / Low setting. The previous reading will be displayed if you have chosen the Show Previous Reading setting and if the previous reading is passed from the billing software.
Installation & Operation Manual • The number of unexpected manual reads (AMR accounts with a manual read instead of an automated read) • The number of Tampers that have not yet been processed • The number of Encoder Errors that have not yet been processed • The number of Meter Popup Comments that have not yet been viewed • The number of Skipped meters The screen looks like this.
Trimble® Ranger™ When you have finished examining the statistics and information, select the “Close” LEFT Soft Menu key to return to the Utilities menu screen. Date/Time To change the date, use the Windows® function for date and time, which is accessed through the Change Date/Time program on the desktop. Battery Info If you need additional information regarding the change status of the battery, press the Battery Info “B” button from the Utilities menu.
Installation & Operation Manual The Settings are organized by topics. Here is the Settings Menu. The Hardware Settings screen looks like this. Clicking in the field will change the COM port value. To save your changes, select the “Save” RIGHT Soft Menu key. To cancel your changes, select the “Cancel” LEFT Soft Menu key. There are three Program Options Settings screens and they look like this.
Trimble® Ranger™ The Settings for Program Operation control how the READCENTER® Field Application software reacts to different meter reading conditions as follows: • Show Account Comments – when checked and Comments exist for the meter, they are displayed automatically when the meter is next to be read. • Show No Usage – when checked and the meter reading matches the previous reading, the No Usage message is displayed.
Installation & Operation Manual High/Low Options Settings Screen • Advance on High/Low – when checked and a high or low reading as just been entered, the READCENTER Field Application software will automatically display the next meter to be read. • Beep on High/Low – when checked and a high reading has just been entered, the READCENTER software will sound 3 beeps to signify the high reading. Two beeps will denote a low reading.
Trimble® Ranger™ Customizations Settings screens (1 to 3) • “Bookmarks Display Using Field” : The selected field will determine what data field is used to display a meter in a list of meters. You cycle through all available field types by tapping on the button. • “Search Hot Key” : The selection determines what happens when you utilize the Search hot key or quick key on the Read screen.
Installation & Operation Manual • “Skipped Meter Definition” : The selection determines what Comment codes (Trouble or Reader codes) are used to indicate a Skipped Meter. You can also disable Skipped processing by selecting “Skip not used.” • “Show message when automated read is applied to a skipped service” : When checked, the user will be notified when a Skipped meter is read via an automated read.
Trimble® Ranger™ Pressing the New Account button will bring up this screen. You can tap on the box to the right of “Name”, “Addr” and “AMR S/N” buttons to place your editing cursor in those fields. Simply start typing the text you wish. The “Name”, “Addr” and “AMR S/N” buttons open an on-screen keyboard to use for text entry.
Installation & Operation Manual Searching for a Route To search for the first meter in a route, press the “M” key from the reading screen to display the read menu. Then press the “S” key to display the Searching menu. You’ll see this screen. Choose the Select Route “R” key to display all of the routes that are currently loaded. You’ll see a screen similar to this.
Trimble® Ranger™ Progress Reporting by Route To view the progress of meter reading, use the Progress function: from the read screen press “M” for the menu, “U” for Utilities, and “P” for Progress. Either way, you’ll see a screen similar to this. Select the “Route Progress” RIGHT Soft Menu key to display the progress for the first route. You’ll see a screen like this.
Installation & Operation Manual Route Completion Messages While you are reading meters, the READCENTER® software is monitoring progress for all of the meters loaded into the handheld. If the last meter in a route is read, you’ll see a message like this denoting that the route is completed. Select the “OK” LEFT Soft Menu key to acknowledge that you have seen the alert message. The Route Completion messages will also be displayed if you are entering the read screen after displaying the Copyright screen.
Trimble® Ranger™ • Read the meters in the route or routes -- Read/Program Meters from the Trimble Ranger Main Menu -- Badger Meter ORION® meter readings will be gathered as they are received when the Trimble Ranger is in automatic mode.
Installation & Operation Manual To access the Badger Meter ORION Programming functions press the “P” key from the ORION Quick Read screen, and then from the Copyright screen of the READCENTER-Quick Read program, enter your 3 to 5 character User name and select the “OK” RIGHT Soft Menu key. You’ll see this screen: Note that you must perform a Read function before you can perform any other function.
Trimble® Ranger™ Reading the Endpoint Through the Optical Port To use the Programmer to Read the endpoint’s meter reading information, align the optical port on the bottom of the handheld computer and the LED and select the “Read” RIGHT Soft Menu key. If the port and the LED are aligned, you’ll see this message : Once the endpoint information has been read, the other fields on the screen will be updated. Once all the information is gathered, you’ll hear a beep and see this screen.
Installation & Operation Manual Using the Programmer to start a Endpoint If a Badger Meter ORION Endpoint is required to start its meter reading broadcast prior to registering usage, align the optical port and the LED and touch the “S” key or tap the “Start” button on the screen. Here’s what you would see if you started endpoint # 82397512.
Trimble® Ranger™ Changing the Odometer setting The most common use of the SET ODOMETER function is to clear a Tamper condition reported by a Endpoint. Besides clearing the tamper, the SET ODOMETER function will also allow you to change the meter reading stored in the endpoint.
Installation & Operation Manual Now we follow the steps for setting the Odometer value. First, we must place the optical port over the endpoint’s LED and perform the READ function. Next, we must update the odometer value on the display. Use the backspace key to delete the current odometer value from the Read step, and enter the desired odometer reading (12345). Now touch on the Set Odometer button.
Trimble® Ranger™ The Quick Read Menu is accessed from the Trimble Ranger Main Menu, and looks like this. The Quick Read Choice screen allows you to perform quick reads for each type of reading technology you use by pressing the button for that technology. Badger Meter ORION® Quick Reads Badger Meter ORION Quick Reads offer you great flexibility.
Installation & Operation Manual If you wish to look for a reading from a specific Badger Meter ORION receiver, use the RF S/N tab to choose and enter the desired serial number. The RF* tab is used when you wish to monitor all of the ORION endpoints in the area. • S/N field : The ORION Serial Number of interest. You can enter this number via the keypad on your Trimble Ranger. • MT field : Displays the Meter Type of the Serial Number once it has been heard.
Trimble® Ranger™ The table shows you each transmission heard from the specified S/N, with the more recent reads at the top. The “Δt” column shows the total number of seconds between reads. This screen shows an example of a Badger Meter ORION Gas endpoint. Note that the table has “Index-Sub” instead of “Reading.” This is necessary since a reading for an ORION Gas endpoint has both a main reading portion, and a sub count portion.
Installation & Operation Manual Here are five examples of the Wildcard Radio Read screen (RF *): A Badger Meter ORION Gas endpoint A Badger Meter RTR with “Potential Leak” indicated A Badger Meter All Digital Encoder with “No Usage” indicated 1-11 Page 73
Trimble® Ranger™ A Repeated Water A Repeated Gas • Reset “E” button: this will clear out all recorded reads and begins collecting reads anew. • Unique S/Ns “U” checkbox: When checked only unique ORION S/Ns will be collected; otherwise, all S/Ns are collected, even duplicates. • Left/Right cursor on the Trimble Ranger keypad: Moves you forward and backward in the collected readings. • “Next” RIGHT Soft Menu key: Same as Right cursor key. Moves you forward in the collected readings.
Installation & Operation Manual When you reach the end of the available reads and press the Right cursor to go beyond the last read, you will be informed of the problem: Also, if you attempt to press the Left cursor key to move beyond the first reading, you will be notified of that issue as well: When you have completed your Quick Reads, press the Close “C” button.
Trimble® Ranger™ WHAT IF THINGS GO WRONG In the unlikely event that you experience difficulty using the Trimble Ranger, we’d like you to take some steps to help us return your Trimble Ranger to proper operation. This section gives you guidelines on how to respond if the Trimble Ranger reports a problem. Restarting Windows® There are times that occur in which the Windows operating system receives conflicting information.
Installation & Operation Manual In some cases, the Specialist will direct you to perform some steps if the problem happens again. This will gather very valuable information that will speed the investigation of the problem. If the problem does happen again, please follow those steps and call the Hotline. The Specialist will gather the information for that particular problem, and direct you if further action is needed.
Trimble® Ranger™ Intentional Blank Page Page 78 1-11
Installation & Operation Manual Intentional Blank Page 1-11 Page 79
ORION® is a registered trademark of Badger Meter, Inc. Other trademarks appearing in this document are the property of their respective entities. Copyright 2011 Badger Meter, Inc. All rights reserved. Due to continuous research, product improvements and enhancements, Badger Meter reserves the right to change product or system specifications without notice, except to the extent an outstanding contractual obligation exists. Badger Meter | P.O.