Installation guide

ManualsBrandsB-Tech Manualsaudio & home theatreBT10

BT10

HI-LOGIC PLUS™ SPEAKER FLOOR STANDS

INSTALLATION GUIDE & PARTS LIST

This Pack Contains 2 Speaker Stands

B-TECH AUDIO VIDEO MOUNTS

www.btechavmounts.com

CONTENTS

INSTALLATION TOOLS REQUIRED

FEATURES

Crosshead

screwdriver

Installation Safety Notes.....................................................................................................................2

Parts List.............................................................................................................................................4

Installation Instructions.......................................................................................................................6

Product Dimensions..........................................................................................................................11

B-Tech Contact Details.....................................................................................................................12

PLEASE KEEP THIS FOR FUTURE REFERENCE

4mm Hex Key

(Supplied)

REG DESIGN NO: 3003354

● Designed for home cinema speakers up to 10kg (22lbs)

● Die-cast base for greater stability, esoteric performance

and to curb unwanted vibration

● Adjustment height: 660mm (26”) – 1200mm (47.2”)

● Suitable for speakers with single point, dual point

and keyhole fixings

● Alternative speaker clamp supplied for speakers

without fixing holes

● Comprehensive mounting kit included

● Integrated cable management with

speaker cable pull-through wire

● Simple assembly and speaker mounting

● This pack contains 2 floor stands

Summary of content (12 pages)

PAGE 1
BT10 HI-LOGIC PLUS™ SPEAKER FLOOR STANDS INSTALLATION GUIDE & PARTS LIST This Pack Contains 2 Speaker Stands PLEASE KEEP THIS FOR FUTURE REFERENCE FEATURES ● ● ● ● ● ● ● ● ● Designed for home cinema speakers up to 10kg (22lbs) Die-cast base for greater stability, esoteric performance and to curb unwanted vibration Adjustment height: 660mm (26”) – 1200mm (47.
PAGE 2
INSTALLATION SAFETY INSTRUCTIONS CAUTION: These stands are intended for use only with the maximum weights indicated. Use with speakers heavier than the maximum indicated may result in instability causing possible injury. Do not attempt to install this product until all instructions and warnings have been read and properly understood. Please keep these instructions for future reference.
PAGE 3
CS Společnost B-Tech International Ltd. doporučuje provést instalaci tohoto produktu prostřednictvím odborného instalátora AV či jinak způsobilé osoby. Společnost B-Tech International Ltd, její distributoři a prodejci nenesou odpovědnost za škody nebo zranění způsobená nevhodnou instalací. Tento výrobek je nutno umístit do vhodné konstrukce a používat jen po uvedenou maximální výšku. DE B-Tech International Ltd.
PAGE 4
BT10 PARTS LIST 6 10 CLAMP ASSEMBLY 8 9 7 TUBE ASSEMBLY 1 2 3 Suitable for loads up to 10kg (22lbs) 5 4 4
PAGE 5
REF 11 12 PART NAME QTY 1 TUBE ASSEMBLY 2 2 HEIGHT ADJUSTMENT COLLAR 2 3 FLOOR BASE 2 4 M22 NUT 2 5 RUBBER FEET 6 6 M6 X 25mm HEX SCREW 2 7 CLAMP BRACKET 2 8 SPEAKER CLAMP 4 4 9 M6 x 60mm SCREW 10 FOAM PAD 4 11 DUAL POINT SPEAKER FIXING 2 12 SINGLE POINT SPEAKER FIXING 2 13 SPEAKER CABLE PULL-THROUGH WIRE 1 14 4mm HEX KEY (FOR PART 6) 1 INTERFACE KIT 13 A M5 X 12mm SCREW 4 B M6 X 12mm SCREW 4 C ¼” X ½” UNC SCREW 4 D ¼” X ½” UNC SCREW (FOR PART E) 2
PAGE 6
INSTALLATION INSTRUCTIONS 1 Attach tube to the floor base.
PAGE 7
2 Stick the rubber feet to the bottom of the floor base.
PAGE 8
3 i. Feed the pull-through wire through the hole at the top of the tube down to the floor base. 1 13 3 13 ii. Attach the speaker cable to the top of the pull-through wire, then pull the cable all the way through the tube.
PAGE 9
4 Choose an adaptor for the speaker.
PAGE 10
5 Loosen the height adjustment collar, adjust height then retighten.
PAGE 11
BT10 PRODUCT DIMENSIONS FLOOR BASE DUAL ADAPTOR 68mm 2.7" 56mm 2.2" 86mm 3.4" 290mm 11.4" 300mm 11.8" 10mm 0.4" SINGLE ADAPTOR 20mm 0.8" O18mm 6.5mm 0.3" 660mm 26" O 8mm 0.3" MIN 90mm 3.5" MAX 165mm 6.5" 90mm 3.5" (0.9") O ADJUSTABLE CLAMP MIN MAX 1200mm 47.2" 26mm 1" (0.7") O23mm 12mm 0.5" THESE INSTRUCTIONS ARE INTENDED AS A GUIDE ONLY AND B-TECH ACCEPTS NO LIABILITY FOR THE ACCURACY OF THE INFORMATION CONTAINED IN THIS DOCUMENT.
PAGE 12
www.btechavmounts.com B-TECH AUDIO VIDEO MOUNTS HEAD OFFICE Bennett House, Long March, Daventry, Northants NN11 4NR, UK Email: info@btechavmounts.co.uk EUROPE Brixtonlaan 32, Zaventem 1930, Brussels, Belgium Email: info@btechproav.com NORTH AMERICA 203 Eggert Road, Buffalo, NY 14215, USA Email: info@btechavmounts.com ASIA PACIFIC Ruby Industrial Complex, Singapore 347740 Email: info@btechavmounts.com.sg ©2009 Bennett Technologies Limited. All rights reserved.