B&R wireless board "RFM-2-NF" Standard Documentation for Radio Equipment Certification Date: 2019-04-09 Project number: N/A B&R reserves the right to change the contents of this document without notice. The information herein is believed to be accurate as of the date of publication; however, B&R shall not be liable for any errors or omissions it may contain.
B&R wireless board "RFM-2-NF" Standard Documentation for Radio Equipment Certification Version information I Version information Version Date Comment Responsible 1.0 2018-10-24 First edition Roland Sevcik 1.1. 2018-11-08 China Requirements added / Figure 8 refreshed Roland Sevcik 1.2. 2018-12-04 Test Conditions in Chapter 2 added Roland Sevcik 1.3 2018-12-20 Statement user manual added, Link of BOM corrected, Statement 8.2, Roland Sevcik 8.3 and 8.
B&R wireless board "RFM-2-NF" Standard Documentation for Radio Equipment Certification Table of contents IV Table of contents 1 Introduction ................................................................................................................. 4 2 Operational description ............................................................................................. 4 3 .Block diagram ............................................................................................................
B&R wireless board "RFM-2-NF" Standard Documentation for Radio Equipment Certification Introduction 1 Introduction This document describes the structure, the basic specification, the main properties and main functionalities of the B&R wireless board “RFM-2-NF” as required for the certification of radio equipment. The optional annexes may contain additional papers like datasheets, certificates, declarations, power of attorney, and similar documentation.
B&R wireless board "RFM-2-NF" Standard Documentation for Radio Equipment Certification 1) Cable Power Supply – Panel Cable Power Supply – Panel no >3m no Cable PC – Panel (DVI-D) no >3m no Wiring for PE/FE-connections (to panel and PC) no N/A no brown: white: blue: black: grey: +24V d.c +24V d.c -24V d.c -24V d.c PE/FE Wires of the PE/FE-network should be as short as possible and must be prepared by the test house in respect to the local test environment.
B&R wireless board "RFM-2-NF" Standard Documentation for Radio Equipment Certification Block diagram 3 Block diagram The block diagram shows the basic elements of the RFM-2-NF, the standardized interface (USB), the on board voltage regulator and the used parts of the SRD controller. Permanently disabled or not used elements of the SRD controller are pictured in grey color and are not relevant for radio equipment compliance assessment. Same for auxiliary, ancillary equipment and accessories.
B&R wireless board "RFM-2-NF" Standard Documentation for Radio Equipment Certification The main components are: ID Manufacturer Type/Material Remarks SRD controller Host connector LEDs Printed pattern antenna Shielding ELATEC interchangeable interchangeable N/A interchangeable TWN4 multitech nano interchangeable interchangeable N/A interchangeable Not a standard USB connector Optical user interface (status LED’s) PCB material FR4, 1,6 mm 4.
B&R wireless board "RFM-2-NF" Standard Documentation for Radio Equipment Certification Schematics 4.4 Schematics N/A 4.5 Part list / BOM See section 4.1 (main components) 5 Host interface description 5.1 Hardware The host interface provides isolated power supply 5 VDC ±5%, power consumption max. 500 mA (typically 120 mA with RF field on) and the data exchange interface lines (USB protocol) to a B&R Industrial PC. Non-standardized cable between RFM-2-NF and PC. 5.
B&R wireless board "RFM-2-NF" Standard Documentation for Radio Equipment Certification Auxiliary equipment 7 Auxiliary equipment This section describes the used auxiliary equipment and refers to hardware, software and instructions for conducting RF testing and is addressed to inspection engineers. It is not part of the ordinary user manual bundled with the product, but describes the test jig.
B&R wireless board "RFM-2-NF" Standard Documentation for Radio Equipment Certification If testing under special environment conditions is necessary, the software BurnIn Test V8.1 Pro can be used to force the system to process graphic data. The following settings in the menu item “Configuration” are recommended for testing. To start the test, click the green symbol with the hint “Start selected test” in the symbol bar of the main window.
B&R wireless board "RFM-2-NF" Standard Documentation for Radio Equipment Certification Labeling 8 Labeling This section describes the labeling, means marking of the module, the end-device (product that incorporates the module), the packaging and requirements for the manual in respect to the requirements for radio equipment. The final labels can have additional information, due to other requirements. 8.
B&R wireless board "RFM-2-NF" Standard Documentation for Radio Equipment Certification End-Device-Marking 8.2 End-Device-Marking The end-device (host) containing the B&R wireless board (RFM-2-NF) must show the following markings: Domain/Country EU Marking USA Canada This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s license-exempt RSS(s) and part 15 of the FCC Rules.
B&R wireless board "RFM-2-NF" Standard Documentation for Radio Equipment Certification Packaging-Marking 8.3 Packaging-Marking This section describes the necessary information on the packaging (sticker) of a B&R end-device that contains an RFM-2-NF but also for the packaging (sticker) of the B&R wireless board RFM-2-NF when shipped for retrofit or as spare part. In case of retrofitting the labeling requirements of an end-device must be taken into account.
B&R wireless board "RFM-2-NF" Standard Documentation for Radio Equipment Certification de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. Japan China none none The information for the end-user described above is implemented in the user manuals of the end-device(s).
B&R wireless board "RFM-2-NF" Standard Documentation for Radio Equipment Certification Figure index 13 Figure index Figure 1: Swing arm version test jig (typical connection scheme) ................................................................ 5 Figure 2: Cabinet version test jig (typical connection scheme) ..................................................................... 5 Figure 3: B&R wireless board “RFM-2-NF” block diagram .........................................................................
B&R wireless board "RFM-2-NF" Standard Documentation for Radio Equipment Certification Table index Table index Table 1: Version information.......................................................................................................................... 2 Table 2: Distribution ....................................................................................................................................... 2 Table 3: Organization of safety notices ..............................................
B&R wireless board "RFM-2-NF" Standard Documentation for Radio Equipment Certification Index Index D S Distribution ............................................................ 2 Safety guidelines .................................................. 2 F T Figure index ........................................................15 Table index ........................................................ 16 Table of contents ................................................. 3 I Index .........................
