Table of Content Section 1: Introduction to GT Mini Contents of the Box 02 Installation of GT Mini levee 17 Section 2 : Working with GT Mini Interacting with GT career 23 introduction to B Medical Connect ADD 31 Section 3: Using Advanced Con fig.
PART ONE Contents of the Box G1 Mini with Frame Battery Pack Temp Sense 810 18mm eg 02
Contents of the Box GT Mini Temp Sense 810 Battery Pack Screws Lae 3M Waterproof Tape 2 x 2.
Detailed Specification Battery Pack Specifications Sheet Constructed using industrial plastics, the battery pack hosts 4 Limn O: chemistry-based cells with a capacity of L000OmAh each. Connected in parallel, the total capacity of the battery pack thence is 4000mAh.
Detailed Specification Material Dimension Battery Cells Battery Capacity / Cell Battery Voltage Battery Chemistry Battery Connectivity Battery Operating Temperature Battery Storage Temperature 05 ABS 53mm (L) by 64mm (W) by 12mm (H} 04 1000mAh av Limn O: Parallel -10°C to 60°C Room Temperature
Construction + Screw Holes Two screw holes are provided to fasten the battery pack into the GT device. The screw holes are designed to host 2.5mm screw heads. Battery Connector ._ . Two pin battery connector protrudes from the battery pack. This connector slides into the GT device to power the device. Special care is to be taken when inserting the battery pack into the GT device.
Detailed Specification Temp Sense 810 Specifications Sheet Constructed using industrial plastics, Temp Sense B10 hosts, BLE circuitry, Temperature Sensor and the batteries. The batteries survive the sensor for b years.
Detailed Specification Physical Battery Material Dimension Battery Cells Battery Capacity / Cell Battery Voltage Battery Chemistry Battery Storage Temperature 08 ABS 70mm (L) by 28mm (W) by 08mm (H) 02 354mAh 3v LIMN Room Temperature
Detailed Specification Temperature Sensor Temp Sense 810 Type Accuracy Operating Temperature Grading Certification 09 Digital +0.1°C (maximum) from —20°C to 50°C +0.15°C {maximum} from —40 °C to 70°C +0.2°C (maximum) from —40°C to 100°C +0.
Construction QR Code Identifier QR code that uniquely identifies the Temp Sense 810. The QR code is used for pairing the Temperateness « with the GT Mini. Vv Dual Batteries Dual batteries with chemistry of LIMN that survive a vast temperature range of -40°C to +125°C. Sensing Tip Stainless steel-based sensing tip that can measure the air temperature or touch based temperature. Constructed using industrial plastics, Temp Sense 810 hosts, BLE circuitry, Temperature Sensor and the batteries.
Detailed Specification Global Tracker Mini Specifications Sheet Constructed using industrial plastics, Global Tracker hosts, BLE circuitry, battery monitoring circuitry, display, buzzer, Temperature Sensor, memory, real time clock and battery. The batteries i.e. the battery pack survives the device for 5 years.
Detailed Specification Physical Battery Temperature Sensor Material Dimension Battery Pack Type Accuracy 13 ABS 120mm (L) by 84mm (W) by 20mm (H) 4000mAh Digital +0.1°C (maximum) from 20°C to 50°C +0.15°C {maximum} from —40 °C to 70°C +0.2°C (maximum) from —40°C to 100°C +0.
Detailed Specification Operating Temperature GT Mini Grading Certification Calibration Screen Type Display Size Display resolution Buzzer Type 14 -10°C to +60°C Medical Grade MAST E1112 and ISO80601 -2-56 INST traceable, ISOMERIC 17025 Factory calibrated as per ISOMERIC 17025 E-ink display 29" 296 px x 128 px Pie
Detailed Specification Protection Connectivity Button Certification Volume Waterproofing Type Technology Version Type 15 75dB P67 Short Range Radio Bluetooth Low Energy 5.
Construction B Medical Logo Laser Printed B Medical logo QR Code QR Code for uniquely identifying 1 the device and for pairing the ~ : application with the device. Push Button t-. E-Ink Display Single rubberized push Low power 2.9” e-ink display button for interactivity. with 296 pixels x 128 pixels. Air Vents & Conduits Air vents for Ambient temperature Sensor Buzzer sound.
PART TWO Installation of GT Mini (Device Preparation) STEP 1 Remove the outer frame. The frame can be removed by pulling on the notch in the bottom.
STEP 2 insert the battery pack into the GT Mini device. Special care is to be taken while pushing the connector into the device {black connector side facing up).
STEP 3 Upon pushing the battery pack into the device, all the way IN, the device will boot up and refresh {can take up to 65 seconds).
installation of GT Mini (Device Mounting) STEP 1 Use the 2.5mm screws in the box to fasten the battery pack into the GT Mini device. This will ensure that the battery pack is secured. se. 2 x 2.
STEPS Align and mount the GT Mini on the RCW. The 1Bmm screws can be used for the same. Frame can then be affixed once mounted.
STEP 6 Using the 3M stickers in the box, affix the Temp Sense 810 inside the RCW. The metal sensing element should be facing up. Stick 3M Sticker on the back side of Temp Sense B10.
PART ONE Home Screen : Understanding Screen iconography The E-ink display on the device is equipped with several icons that not just indicate the various functionalities of the device but also the status of the product at a given time. Here's what you'll see on the Home Screen: HIGH 2.5 °C 1.00 Oh of Au2.
SYMBOL: OK This icon is displayed when the temperature inside the vaccine box and the ambient temperature has been within the thresholds. SYMBOL : ALERT This icon is displayed when the temperature inside the vaccine box and the ambient temperature has breached the set thresholds. OPED SYMBOL : TEMPERATURE SLIDER Bl 2.5 TC This icon group displays the {6 current temperature as measured by the Temp Sense 810.
BITNET wham . nn Latte if the measured temperature is within the thresholds the arrow stays in the middle of the HIGH/ LOW bar. However, if the measured Temperature is HIGH, the arrow points to the HIGH in the HIGH/ LOW bar. SYMBOL : EMPTY TEMPERATURE When there is a disconnection between the Temp sense 810 and GT Mini the temperature is not available. This is illustrated by dashes.
Empty State Charged State SYMBOL: On Trip This icon is displayed (upon screen refresh) when the RCW is configured TRIP. The trip status can be changed from the app. SYMBOL : Temp Sense 810 Connected This icon is displayed when the GT Mini is connected to Temp Sense 810. SYMBOL : Ambient Temp. This icon is displayed when the vaccine box has measured the AMBIENT TEMPERATURE.
Screen Navigation : Home Screen History Screen GT Mini displays two different screens. We call them the Home Screen and the History Screen. One can shift from Home Screen to History Screen by pressing the button on the device once. On pressing the button again, the data for the previous date is shown. The device automatically comes back to Home Screen if no activity is detected for 20 seconds.
Ml 2:5 ¢ LOW Eb af A050 oT ETC Home Screen Pantomimic dL DAY AMBIENT IEEE Historical Screen 29
Historical Screen : Understanding Screen iconography SYMBOL : Date 2% men This icon on the History Screen displays the data of that specific date. SYMBOL : Time Zone rE: Wroclaw This icon in the History Screen displays the time-zone of that specific date. +0.0 signifies GMT. NYBBLE a Temperature Table The temperature data of the specific day for both Ambient Temperature (outside) and the Internal Temperature Temp Sense 810) are displayed.
PART TWO Mobile Application : Search & Download Available on both i05 and Android application stores, one can download from the respective stores either by searching for "B Medical Connect” or by scanning the displayed QR code for the respective stores.
STEP 1 Launch the downloaded application on the phone by clicking on the 'B Medical Connect’ app icon.
STEP 2 After application splash screen is displayed ‘Application Permissions are requested’. These MUST be given for the application to work properly.
STEP 3 After giving permissions you need to login by putting correct credentials.
STEP 4 Once you are logged in home screen is displayed. The app is ready to be use.
Connect to G1 Mini STEP 1 Launch the downloaded application on the phone by clicking on the ‘B Medical Connect’ app icon. Wait for the Home Screen.
STEP 2 Click on the push button on the GT Mini and let the Home Screen transition to History Screen. The GT Mini is discover able on Bluetooth and is now ready to connect to the App. Push Button Single rubberized push button for interactivity.
STEP 3 Click on the button in the Home Screen of the App. This opens the Scan Screen. This is used to identify and connect to GT Mini.
STEP 4 Using the camera window in the Scan Screen, point it to the GT Mini's QR code affixed on the top right corner of the device. Once the QR is detected, the APP will show the connect button. Click ‘Connect’.
STEPS On clicking ‘Connect’, the app attempts to connect to the GT Mini. On successful connection, the app fetches all data and records from the device.
STEP 6 The data fetched is processed and shown on the ‘Device Screen’ of the application. The ‘Device Screen’ is the screen from where both information and control of the device is managed. wit da A Hy Wanna ¢ sealant.
Add to Favorites STEP 1 After Installing B Medical Connect application, please tap on the icon available at the bottom of the screen to connect GT Mini to your phone.
STEP 2 Summary screen will be displayed once you are connected to GT Mini. Tap on the menu available at the upper right corner of the screen.
STEP 3 After tapping on menu, you will have a few options. Please select ‘Add to Favorites’ from there.
STEPS After adding GT Mini to favorites, it will appear on the home screen. And you can access it any time without scanning QR Code.
Remove from Favorites STEP 1 After adding GT Mini to favorites, you can access it from the home screen. Please tap on it to connect (the data fetch is done only once per connection).
STEP 2 You will be provided two options. Please select ‘Connect’ and press the button on GT Mini as shown earlier.
STEP 3 Summary screen will be displayed once you are connected to GT Mini. Tap on the menu available at the upper right corner of the screen.
STEP 4 After tapping on menu, you will have a few options. Please select ‘Remove from Favorite.
STEPS You will receive confirmation of GT Mini removed from favorites.
STEP 6 After removing GT Mini from favorites, you will no longer see any GT Mini information on home screen. If you wish to see all information again, please try connecting it by scanning the QR Code.
Update Device STEP 1 Tap on the desired GT ID which is available on Home screen to connect. If you have not added GT Mini to favorites, please tap on button to scan QR code and connect.
STEP 2 You will be provided two options. Please select ‘Connect’ and press the button on GT Mini as shown earlier.
STEP 3 Summary screen will be displayed once you are connected to GT Mini. Tap on the menu available at the upper right corner of the screen.
STEP 4 After tapping on the menu, you will have a few options. Please select ‘Update Device’.
STEP 6 Once confirmation is done, device will start updating. You can see the progress from the screen. Upon completion, you will see ‘Device is up-to-date’. LER.
Trip Management (Start Trip) STEP 1 Tap on the desired GT ID which is available on Home screen to connect. If you have not added GT Mini to favorites, please tap on button to scan QR code and connect.
STEP 2 You will be provided two options. Please select ‘Connect’ and press the button on GT Mini as shown earlier.
STEP 3 Summary screen will be displayed once you are connected to GT Mini. Tap on the ‘Trip Settings’ section.
STEP 4 Toggle the slider to change the ‘Trip Status’ to ‘In Trip’. On the Trip setting screen, you can manage certain parameters according to your need.
STEPS Once you are ready please tap on ‘Deploy Con fig’ to confirm your configuration.
STEP 6 After successfully deploying configuration, you can see the ‘Status’ on the summary screen changed to ‘ON TRIP’. The LB symbol will appear on the GT Mini screen upon refresh. wit da A Hy Wanna ¢ sealant.
Trip Management (Stop Trip) STEP 1 Tap on the desired GT ID which is available on the Home Screen to connect. If you have not added the GT Mini to favorites, please tap on button to scan the QR code and connect.
STEP 2 You will be provided two options (View Data and Connect). Please select ‘Connect’ and press the push button on the GT Mini as shown earlier.
STEP 3 Summary screen will be displayed once you are connected to the GT Mini. Tap on the ‘Trip Setting’ section.
STEP 6 After successfully deploying configuration, you can see ‘Status’ on the summary screen changed to ‘NOT IN TRIP’. The LB symbol indicating ‘On Trip’ will also disappear from the GT Mini Screen upon refresh. EEE WE Wiesel < ee A Summary Ha Fa manana van Please note: To export the trip report you must reconnect to the GT Mini and follow the steps in the next section.
Trip Management (Trip Data) STEP 1 Tap on the desired GT ID which is available on the Home Screen to connect. If you have not added the GT Mini to favorites, please tap on the button to scan QR code and connect.
STEP 2 You will be provided with two options (View Data & Connect). Please select ‘Connect’ and press the push button on the GT Mini as shown earlier.
STEP 3 Summary screen will be displayed once you are connected to GT Mini. Scroll down to see ‘Trip Based Data’.
STEP 4 Tap on the drop down menu to select the trip. EE EET ea ¢ sealant.
STEPS You can view and analyses the data from graphs after selecting the trip from the drop down menu. You can Zoom In / Out on a temperature chart for more detailed visualization. wR way FEEL ¢ sealant.
Trip Management (Export Data) STEP 1 Tap on the desired GT ID which is available on the Home Screen to connect. If you have not added the GT Mini to favorites, please tap on button to scan the QR code and connect.
STEP 2 You will be provided with two options (View Data & Connect). Please select ‘Connect’ and press the push button on the GT Mini as shown earlier.
STEP 3 Summary screen will be displayed once you are connected to GT Mini. Scroll down to see ‘Trip Based Data’.
STEP 4 Tap on the drop down menu to select the trip for which you want to export data.
STEPS Scroll down to ‘Report’ and tap on ‘Export Report’ Senegalese 0 Ld Summary FEET ERE Blind an 80
STEP 6 Tap on the desired output format to download the report on your phone. Tap on check box to include “Raw Data" if you want.
Configuration STEP 1 Tap on the desired GT ID which is available on the Home Screen to connect. If you have not added GT Mini to favorites, please tap on button to scan the QR code and connect.
STEP 2 You will be provided two options. Please select ‘Connect’ and press the button on GT Mini as shown earlier.
STEP 3 Summary screen will be displayed once you are connected to GT Mini. Tap on the {2 ‘Configuration’ icon.
STEP 5 After entering passkey you will be able to see configuration screen. Please change settings according to your requirements and deploy the configuration.
Pairing with another Temp Sense STEP 1 Tap on the desired GT ID which is available on the Home Screen to connect. If you have not added GT Mini to favorites, please tap on button to scan the QR code and connect.
STEP 2 You will be provided two options. Please select ‘Connect’ and press the button on GT Mini as shown earlier.
STEP 3 Summary screen will be displayed once you are connected to GT Mini. Tap on the {2 ‘Configuration’ icon.
STEP 5 After entering passkey you will be able to see configuration screen. Click on “ Pair with another Tenseness. NOTE : The pairing and unpaid buttons will only be visible if the Gt Mini that you have connected has firmware version 1.6.1 or above.
STEP 8 Application will scan & show you Temp Sense ID you wish to pair. tap on “Pair” to proceed further and it will get paired successfully.
Unpaid Global Tracker STEP 1 Tap on the desired GT ID which is available on the Home Screen to connect. If you have not added GT Mini to favorites, please tap on button to scan the QR code and connect.
STEP 2 You will be provided two options. Please select ‘Connect’ and press the button on GT Mini as shown earlier.
STEP 3 Summary screen will be displayed once you are connected to GT Mini. Tap on the {2 ‘Configuration’ icon.
STEP 5 After entering passkey you will be able to see configuration screen. Click on “ Unpaid GT". NOTE : The pairing and unpaid buttons will only be visible if the Gt Mini that you have connected has firmware version 1.6.1 or above.
STEP 6 Application will ask your confirmation before pairing. Tap on ‘Yes’ to proceed.
STEP 6 You will receive confirmation for pairing GT and application will take you back to home screen.
Fed de STEP 1 Tap on the desired GT ID which is available on the Home Screen to connect. If you have not added GT Mini to favorites, please tap on button to scan the QR code and connect.
STEP 2 You will be provided two options. Please select ‘Connect’ and press the button on GT Mini as shown earlier.
STEP 3 Summary screen will be displayed once you are connected to GT Mini. Tap on the bell icon available at the upper right corner.
STEP 4 You can check all the notifications received for the GT Mini. Ratepayer AEE 4 Si aaa Dais sda Sold ns SEER Aerie SE Gaia sided Silas Akita Hots RR BEE 105 Types of Notifications & Alerts 1. Ambient temperature threshold breach 2. Temp Sense 810 temperature threshold breach 3.
Trip status — ON / OFF Time zone ~ Default is UTC. Turning this on configures the historical data to the time zone as that of the mobile device that has connected with the GT Mini. Sensor low / high thresholds ~ The upper and lower limits of the temperature sensor can be configured as per the requirements of the load being transported.
STEP 1 After making your preferred changes to the configurable features, click on the ‘Deploy Con fig’ button at the bottom right of the screen.
STEP 2 You will see a confirmation text ‘Configuration Deployed Successfully’. SE important to note Upon deploying a configuration, your phone will automatically disconnect from the GT Mini. To make any new changes to the configurable features vou must reconnect to the GT Mini as per the instructions given in this manual.
Frequently Asked Questions Can multiple mobile devices connect to the GT Mini at the same time? No, only one mobile device may be connected to the GT Mini at any given point. How do | know the MAC ID of the GT Mini and Temp Sense? By scanning the QR codes on each of devices. How do | know which Temp Sense 810 is paired with which GT Mini? The last 4 digits of the MAC ID for both devices should match. How many days of historical data is available? 30 days from the current date.
06. Are the devices and the app CFR Part 11 compliant? Yes. 07. Is the temperature sensor INST traceable? Yes. 08. Why is there an Alarm Delay? As per WHO requirements, there must be a period of time provided for a temperature breach to “settle” back into the per-defined thresholds.
DOWNLOAD OUR APPLICATION Eee Google Play Be Website : www.cwdin.com Manufactured by Marketed by CWD Limited B Medical Systems Sal 101 Ha sham Premiere Bldg, 17. Op der Hei L-9808 Hosing en, 439 Kalevala Rd, Mumbai Luxembourg 40002 Contents of this manual are subject to change without prior notice, C & ® @Copyright 2022 B Medical Systems 5.4 r.