AW-CU427-E AW-CU427-P IEEE 802.11 b/g/n MAC/baseband/radio and Bluetooth 4.2 IoT Module Internal Antenna Datasheet Rev.
Features WiFi MCU Single band 2.4 GHz 802.11 b/g/n 150-MHz Arm Cortex-M4F CPU with single- SDIO v2.0, including DS and HS modes Security–WEP, AES (HW), WPA/WPA2 TKIP (HW), cycle multiply (Floating Point and Memory (personal), CKIP Protection Unit) (SW), 100-MHz Cortex M0+ CPU WMM/WMM-PS/WMM-SA 1 MB Application Flash with 32-KB EEPROM area and 32-KB Supervisory Flash Dara Rate up to 72.
Asymmetric cryptographic methods (AES, (SHA-512, SHA-256) 3DES, RSA, and ECC) and Hash functions Up to 66 programmable IOs 3
1. Introduction 1.1.1 Product Overview AzureWave presents AW-CU427 Wi-Fi & Bluetooth with Microcontroller solution which provides a highly cost-effective, flexible and easy to-use hardware/software platform to build a new generation of connected, smart devices. These smart-connected devices enable device to deliver a broad-range of services to consumers including energy-management, demand-response, home automation and remote access.
WLAN VID/PID n/a WLAN SVID/SPID n/a Frequency Rage WLAN: 2.4 GHz Band Modulation Number of Channels Output Power (Board Level Limit)* Receiver Sensitivity Data Rate Security DSSS DBPSK(1Mbps), DQPSK(2Mbps), CCK(11/5.5Mbps) OFDM BPSK(9/6Mbps), QPSK(18/12Mbps), DBPSK(1Mbps), DQPSK(2Mbps), CCK(11/5.5Mbps), 16-QAM(36/24Mbps), 64-QAM (72.2/54/48Mbps) 802.11b: USA, Canada and Taiwan – 1 ~ 11 Most European Countries – 1 ~ 13 Japan – 1 ~ 13 802.
Bluetooth Features Description Bluetooth Standard Bluetooth 2.1+Enhanced Data Rate (EDR) / BT4.2 Bluetooth VID/PID n/a Frequency Rage 2400~2483.5MHz Modulation GFSK (1Mbps), Π/4DQPSK (2Mbps) and 8DPSK (3Mbps) Output Power Receiver Sensitivity Basic Rate : 8dBm +/- 2dBm (Max Settings) BLE:8dBm+/-2dBm(Max Settings) Min Typ DH5 -91 2DH5 -93 3DH5 -87 Operating Conditions Features Description Operating Conditions Voltage WIFI/BT VBAT:3.2V~4.8V (3.6V Typical) VDD for MCU(except for USB):1.7V~3.
Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
This module is intended for OEM integrators only. Per FCC KDB 996369 D03 OEM Manual v01 guidance, the following conditions must be strictly followed when using this certified module: KDB 996369 D03 OEM Manual v01 rule sections: 2.2 List of applicable FCC rules This module has been tested for compliance to FCC Part 15 2.3 Summarize the specific operational use conditions The module is tested for standalone mobile RF exposure use condition.
requirements required with this module installed. IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization.
This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with greater than 20cm between the radiator & your body. Déclaration d'exposition aux radiations: Cet équipement est conforme aux limites d'exposition aux rayonnements ISED établies pour un environnement non contrôlé. Cet équipement doit être installé et utilisé à plus de 20 cm entre le radiateur et votre corps.
This device is intended only for OEM integrators under the following conditions: (For module device use) The antenna must be installed and operated with greater than 20cm between the antenna and users, 2) The transmitter module may not be co-located with any other transmitter or antenna. As long as 2 conditions above are met, further transmitter test will not be required.
End Product Labeling This transmitter module is authorized only for use in device where the antenna may be installed and operated with greater than 20cm between the antenna and users. The final end product must be ”. labeled in a visible area with the following: “Contains IC: 6100A-CU427 Plaque signalétique du produit final Ce module émetteur est autorisé uniquement pour une utilisation dans un appareil où l’antenne peut être installée et utilisée à plus de 20 cm entre l’antenne et les utilisateurs.
