Model Name: AW-GA200/AW-GA201 802.11g/54Mbps 802.11g Access Point + Wireless Audio Receiver Combo Solution User Manual AzureWave Technologies Inc, 2006 Contents Chapter 1 Introduction.................................................................... 1 Chapter 2 Getting Start with AW-GA100......................................... 1 Chapter 3 How to make wireless audio feature working? ............. 3 Chapter 4 Installation and Setup Wizard.........................................
Chapter 1: Introduction AW-GA100 is 802.11g Access Point + Wireless Audio Receiver Combo Solution. It support following feature Ø Ø 802.11g Access point feature, including AP feature and AP Client feature. Wireless sound card (WSC) feature: Wireless sound card (WSC) is the most advanced technology on wireless audio transmission. Users only need to install Azurewave driver/utility on your computer, computer can stream audio via 802.11 wireless network or 802.3 wire network to the receiver.
Audio Out L/R The Audio Out (Left and Right) ports connect to the Audio In (Left and Right) ports of your audio receiver. Ethernet This Ethernet port connects to Ethernet network devices, such as a switch or router, if using a wired connection. Reset Button There are two ways to Reset the Device's factory defaults. Either press the Reset Button, for approximately ten seconds, or restore the defaults from the Password tab in the device's Web Based Utility.
up status. Ethernet . The Ethernet LED displays two modes. If the LED is continuously lit, the device is successfully connected to a device through the Ethernet port. If the LED is flashing, it is an indication of any network activity. Wireless LAN If the LED is flashing, it means Wireless LAN is acting. Wireless Audio The Wireless Audio LED displays three modes. - LED is off, it means nobody run wireless audio feature (but could be use AP feature).
For detailed installation and instruction of AzureWave wireless audio driver/utility, please refer to Chapter 4 and Chapter 5. Step 2: Power on your AW-GA100, connect AW-GA100 to powered speaker or decoder. Plug-in the power adapter bundled with AW -GA100, the power LED will be light up. AW GA100 DON’T built-in speaker, so you have to connect to “ Powered Speaker” ,Decoder(For SPDIF output) or Home stereo.
Chapter 4: Installation and Setup Wizard 4.1 Install your wireless audio driver and utility Insert Installation CD onto your PC, then click start button and select run, enter “d:\setup.exe” (if “D” is the letter of your PC’s CDROM drive). When auto-installation utility is staring, please follow utility’s instruction to complete Driver/Utility Installation process. After Installation is done, the utility will automatically start the Setup Wizard.
4.2 Setup Wizard 4.2.1 Starting Setup Wizard to configure Device Insert Installation CD onto your PC, then click start button and select r un, enter “d:\setup\setup.exe”(if “D” is the letter of your PC’s CDROM drive). When auto-installation utility is staring, please follow utility’s instruction to complete Driver/Utility Installation process. After Installation is done, the utility will automatically start the Setup Wizard.
AP/Receiver existing on same network. The device name will display on wireless audio utility. Step 2 Wireless setting After you choosing “Create a new network” and enter next step, you can setup SSID and encryption way for wireless security. The device support WEP/None/ WPAPSK(TKIP)/ WPA2PSK(AES)/ WPA2PSK(TKIP)+(AES) Step 3 Encryption Key Then follow instruction to input security key based on different encryption way. Step 4 Network Settings On next step, you will enter the network setting page.
Step 2 Wireless setting After you choosing “Create a new network” and enter next step, you can setup SSID and encryption way for wireless security. The device support WEP/None/ WPAPSK(TKIP)/ WPA2PSK(AES)/ WPA2PSK(TKIP)+(AES) Step 3 Encryption Key Then follow instruction to input security key based on different encryption way. Step 4 Internet Setting AW-GA201 support following connection type -DHCP -Static IP -PPPoE -PPTP AW-GA201 will detect you network status and show your network protocol as default item.
Device Management The devices windows will show up “device name” of wireless audio receiver connect to the same network. Users can use “connect” and “disconnect” to connect 1 or more device. Note: AW-GA201 support multi-link feature, it means PC can steam music to 1 or more devices. But due to system limitation, if AW -GA201 work as AP or RT mode, we strongly suggest NOT to run “multi-link” feature on the device, otherwise it could be cause audio stream quality issue.
and operation of this product. Common Problems and Solutions 1. The music is coming from PC’ s speaker and not the speaker that connects to the AWGA100. Open the AzureWave Wireless Audio Utility to connect to the AW-GA100 in order to listen to music from speakers that connect to the Device. 2. My Wireless Device has been connected on the utility, but there is no music coming from the speaker. • Check LED on front panel, make sure the wireless audio LED(blue one) is lighting up and flashing.
Why can’ t I see the Device on my Device Utility? • My Device has a wired connection to my network. • Restart the PC and try again. • Check all the cable connections and power. My device is wirelessly connecting to my network, so why can’ t I see the Device on my Device Utility? • Restart the PC and try again. • If it’ sthe first time, please return to the setup wizard again and make sure you configure the Device properly or move your Device closer to your wireless access point and try again.
