AW-CU300 EVB User Guide (PCB 2223 Ver:I1,I2) V0.2 2015/06/12 Kai.
Relative Software Application Software •FTDI VCP Drivers (FT2232D) •Libusb-win32-bin-1.2.6.0 •Cygwin Set-up Procedure 1. Download FTDI VCP Drivers (FT2232D) 2. Download Libusb-win32-bin-1.2.6.0 3. Set Up CU277 EVB for Windows 4. Install FTDI VCP Drivers 5. Install Libusb-win32-bin-1.2.6.0 6. Install Cygwin 7. Insert file “OpenOCD.zip” 8. Burning MCU Image with normal firmware 9. Run WIFI Normal Driver 10. Burning MCU Image with MFG firmware 11.
Relative Hardware I1 EVB Power Supply Option: 1. 2. USB B-type 5V Input Power Jack 5V Input (If the USB B-type driving force shortage) CU300 Wake Up CU300 Push SW External QSPI (32M-Bit) flash to CU300 AW-CU300 External 32.768KHz to CU300 LDO 5V to 3.3V LDO 5V to 3.
Relative Hardware I2 EVB Power Supply Option: 1. 2. USB B-type 5V Input Power Jack 5V Input (If the USB B-type driving force shortage) CU300 Wake Up External QSPI (32M-Bit) flash to CU300 CU300 Push SW External 32.768KHz to CU300 AW-CU300 LDO 5V to 3.3V LDO 5V to 3.
1. Download FTDI VCP Drivers (FT2232D) Install the driver manually. You can get the driver from FTDI’s web site. http://www.ftdichip.com/Drivers/VCP.
2. Download Libusb-win32 You can get the driver from libusb-win32’s web site. http://sourceforge.
3. Set Up CU300 EVB I1 for Windows The USB port (B type) connects the CU300 evaluation board to the PC. Please refer to “AW-CU300 EVB I1’s PCB Info” document. 3.
3. Set Up CU300 EVB I2 for Windows The USB port (B type) connects the CU300 evaluation board to the PC. Please refer to “AW-CU300 EVB I2’s PCB Info” document. 3.
4-1.
4-2. Install FTDI VCP Drivers Verifying Driver Installation: To verify that driver installation has completed successfully, you can open the “Device Manager” (right-click My Computer, select Properties). In the System Properties windows, select Hardware, Device Manager. Two “USB Serial Port” should be listed under MY-PC\Ports (COM & LPT) 10 Confidential
5-1.
5-2. Install Libusb-win32 Verifying Driver Installation: To verify that driver installation has completed successfully, you can open the “Device Manager” (right-click My Computer, select Properties). In the System Properties windows, select Hardware, Device Manager. One “USB Serial Converter A” should be listed under MY-PC\Ports (lib usbwin32 devices) DONE 12 Confidential
6-1. Install Cygwin Install Cygwin: 1. Install Cygwin from: http://www.cygwin.com/setup_x86.exe (for x86 32-bit systems) or http://www.cygwin.com/setup_x86_64.exe (for x86 64-bit systems) 2. Select the option Install from Internet 3. Use default installation path: c:\cygwin. If you chose an alternate installation directory, please make sure that there are no spaces in the path. 4. Pick the Local Package Directory (this is the download cache directory) 5. Select the option Direct Connection 6.
6-2.
7-1. Insert file “OpenOCD.zip” Unzip “CU300_OpenOCD.zip” and put “readelf.exe” to C:\cygwin\bin 15 Confidential
7-2. Insert file “OpenOCD.zip” Unzip “CU300_OpenOCD.zip” and put them to C:\cygwin\ 16 Confidential
7-3. Insert file “OpenOCD.zip” Process C:\cygwin\Cygwin.
7-4. Insert file “OpenOCD.
8-1. Burning Normal F/W Check config_normal_RTC.txt, layout.
8-2. Burning Normal F/W Key in command : ./flashprog.sh -l layout.txt -b config_normal_RTC.
8-3.
9-1.
9-2.
10-1. Burning MFG F/W Check config_mfg.txt, layout.
10-2. Burning MFG F/W Command : ./flashprog.sh –l layout.txt –b config_mfg.
10-3.
11-1.
11-2.
Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
This device is intended only for OEM integrators under the following conditions: The antenna must be installed such that 20 cm is maintained between the antenna and users, and The transmitter module may not be co-located with any other transmitter or antenna. As long as 2 conditions above are met, further transmitter test will not be required.
Industry Canada statement: This device complies with RSS-247 of the Industry Canada Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Ce dispositif est conforme à la norme CNR-247 d'Industrie Canada applicable aux appareils radio exempts de licence.
This device is intended only for OEM integrators under the following conditions: (For module device use) 1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and 2) The transmitter module may not be co-located with any other transmitter or antenna. As long as 2 conditions above are met, further transmitter test will not be required.
End Product Labeling This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may be maintained between the antenna and users. The final end product must be labeled in a visible area with the following: “Contains IC: 6100A-CU300”.
