PRO-XR 2.
ADVISORY CAUTION: DO NOT STORE OR OPERATE THIS PRODUCT NEAR A HEAT SOURCE OR IN AN ENVIRONMENT OF EXTREME TEMPERATURES. AVOID EXPOSURE TO RAIN OR ANY OTHER SOURCE OF MOISTURE. DO NOT SUBMERGE IN WATER. IF EXTERIOR IS EXPOSED TO WATER, WIPE DRY BEFORE USE. DO NOT ATTEMPT TO OPEN THE CASING OR MAKE ANY MODIFICATION TO THE INTERNAL ELECTRICAL COMPONENTS. ELECTRIC SHOCK OR INJURY MAY RESULT. ANY UNAUTHORIZED MODIFICATION TO THIS PRODUCT WILL VOID ANY APPLICABLE WARRANTIES. The PRO-XR 2.
QUICK START GUIDE 1 Attach one of the included antennas to the transmitter (TX) by screwing it to the antenna threads on top. 2 Plug the EX-507XR lapel microphone into the transmitter’s (TX) Microphone Input located on top. 3 Turn on both the receiver (RX) and transmitter (TX) units by pressing and holding down the power button for 1 second. The units should pair automatically, and each show 2 solid green lights.
INTRODUCTION Congratulations on purchasing the Azden® PRO-XR 2.4 GHz Wireless Microphone System. The PRO-XR was designed to provide amateur and semi-professional video producers alike with a high quality, yet affordable wireless audio solution. The PRO-XR has a number of unique features that allow it to perform well even in the face of a crowded 2.4 GHz environment. First, the system auto-scans the full 2.
PRO-XRT TRANSMITTER (TX) ① Antenna ② Power Button ③ Transmission Power Button ④ Input Selector ⑤ Aux Input ⑥ Belt Clip ⑦ Reset ⑧ Microphone Input ⑨ Signal Indicator ⑩ Power Indicator ⑪ Mini USB Charging Port OPERATION Power On/Off Turn on the PRO-XRT by pressing and holding the Power Button ② for 1 second. It may take a few seconds for the transmitter and receiver to connect and show solid green Signal Indicator ⑨ lights.
PRO-XRR RECEIVER (RX) ① Antenna ② Power Button ③ Volume Control ④ Shoe Mount ⑤ Microphone Output ⑥ Reset ⑦ Headphone Output ⑧ Signal Indicator ⑨ Power Indicator ⑩ Mini USB Charging Port OPERATION Power On/Off Turn on the PRO-XRR by pressing and holding the Power Button ② for 1 second. It may take a few seconds for the transmitter and receiver to connect and show solid green Signal Indicator ⑨ lights.
The EX-507XR Lapel Microphone The PRO-XR system comes with a high quality lapel microphone. The lapel mic is omni-directional and powered by the transmitter (via plug-in power) and uses a standard, unbalanced TRS 3.5 mm male connector so it may be used with some other wireless systems if desired. It comes with a lapel clip and attached windscreen. To use the EX-507XR with the PRO-XR system, simply plug it into the Microphone Input located on the top of the transmitter.
Use With a Camera The PRO-XR receiver comes with a standard camera shoe mount attached for easy mounting to a DSLR camera, mirrorless camera, or camcorder. To mount the receiver, slide the shoe mount into the camera’s accessory shoe slot. Tighten the thumbwheel to secure the receiver in the shoe slot. 3.5 mm Mic Inputs: Your camera must be equipped with a 3.5 mm microphone input jack in order to use the PRO-XR system with it.
Connecting to a Mobile Device with TRRS Headphone Jack (Most Android devices / older iOS devices) 1. Connect the male end of the TRS to TRRS Adapter Cable to the headphone jack of your device. 2. Connect one end of the Audio Output Cable to the female end of the TRS to TRRS Adapter Cable. 3. Connect the remaining end of the Audio Output Cable to the PRO-XR receiver’s MIC OUT jack (located on the side of the unit).
Setting Optimal Recording Levels On Camera If you are able to set the microphone recording level on your camera, it is generally best to keep the camera’s gain level low and set the output level of the receiver to the maximum. This is because the preamps in most cameras tend to be of low quality and will add noise to the recording if a lot of gain is used.
Reset Button Both the transmitter and receiver have a recessed reset button located on the back. The reset button acts as a backup to the power button’s “off” function. In case either unit’s power button is unresponsive, the reset button can be used to power it off. To use the reset button, the unit must be powered on. Press the reset button by using a thin, rigid object like a paper clip or tip of a pen; push and hold for 1 second and then release. The unit will power off and need to be turned on again.
SPECIFICATIONS SYSTEM Operating Freq.: Signal-To-Noise: Dynamic Range: Operating Range: Freq. Response: Bit Rate: System Latency: Battery Life Span: Battery Type: Power Supply: 2.4 GHz ISM Band 86 dB A-weighted Mic: 90 dB / Line: 87 dB up to 500 feet in optimal conditions Mic: 60 Hz - 20 kHz Aux: 30 Hz - 20 kHz 384 kbps 4.5 ms 500 cycles (70% peak performance) Lithium-ion 3.7 V, 1200 mAh, 4.