310 DIVERSITY CAMERA-MOUNT UHF WIRELESS MICROPHONE SYSTEM 310UDR - 35BT - 35HT - 35XT INSTRUCTION MANUAL
Thank you for purchasing the Azden 310 Diversity Wireless Microphone system. The components included with your system will vary depending on the system configuration you purchased. Below are the possible system configurations available with the 310UDR Diversity Receiver.
310UDR Diversity Receiver 6 5 1 2 9 3 4 8 7 1. Antennas For the best reception, the antennas should be pointed in an upward position. 2. Power Switch Turns the receiver “ON” or “OFF”. 3. LCD Display Multifunctional display shows battery life, signal strength, and frequency selection. Refer to “LCD Display Readouts” in this manual for further details. 4.
7. Battery Compartment Remove the battery compartment lid by sliding it down. Install two fresh alkaline “AA” batteries. Make sure the battery polarity is correct as marked inside the battery compartment. Alkaline batteries will perform best. 8. Headphone Level Adjustment Turn the dial to adjust headphone audio level. Turn clockwise to increase volume, counter-clockwise to decrease volume. 9. Shoe Mount Assembly First loosen the thumb wheel by turning it counter-clockwise.
14. AUDIO Switch It is best to set the AUDIO switch to “STBY” (standby) prior to first turning the POWER switch “ON”. When you are ready to begin transmitting, turn the AUDIO switch ON. The STBY position acts as a mute function that maintains the RF signal but turns off the audio. 15. LCD Display Multifunctional display shows battery life, audio level and frequency selection. Refer to “LCD Display Readouts” in this manual for further details. 16.
21. Phantom Power Switch Flip this switch to “48V” to turn on phantom power. Use only for microphones that require phantom power. 22. LCD Display Multifunctional display shows battery life, audio level and frequency selection. Refer to “LCD Display Readouts” in this manual for further details. 23. CHANNEL UP/DOWN Buttons Press the UP and DOWN buttons to change the transmission frequency. Group/Frequency numbers are shown on the LCD. 24.
LCD Display Readouts B A C LEVEL 30- 02 BATT E D 310UDR (RECEIVER) A. Battery level indicator: 3 bars = high, 1 bar = low B. Reception level indicator: 4 bars = high, 1 bar = low C. Audio connection indicator. If not lit, this indicates a loss in audio connection at the receiver. D. Receiving frequency “TV Channel” aka Group number: range 30 - 33 E. Receiving frequency “Channel” aka Frequency number: range 01 - 47 X W LEVEL 30- 02 BATT Z Y 35BT / XT / HT (TRANSMITTERS) Z.
Detailed Set Up Instructions The frequency of each unit may be changed by pressing the Up and Down channel buttons located under the LCD in the case of the 35BT, 35XT and 310UDR, or inside the battery compartment in the case of the 35HT.
Avoiding Interference and Drop Outs • Interference from other electro-magnetic sources in the environment is always a risk with any wireless radio technology. When using the system in a new location, always listen with headphones and observe the quality of the audio for a few minutes before you start filming. If you notice any interference noise, it will probably be best to change your transmission frequencies. Continue to monitor audio while filming if possible.
SPECIFICATIONS 310UDR Receiver Frequency Range: Type of Reception: Oscillator: RF Squelch Level: Frequency Response: S/N Ratio: Audio Out: Batteries: Dimensions: Weight: 35BT BodyFrequency Range: Oscillator: RF Power: Frequency Response: Dimensions: Weight: 35XT PlugFrequency Range: Antenna: Max Input Level: RF Power: Input Impedance: Audio Adjust Range: Dimensions: Weight: Frequency Range: Oscillator: RF Power: Frequency Response: Dimensions: Weight: UHF 188 Frequencies (566.125-589.