User Manual

ManualsBrandsAxxess ManualsCar & Vehicle ElectronicsAxxess XSVI-2004 Amplifier Interface Harness for 1997-2004 Chevrolet Vehicles with Factory Amplified System

INSTXSVI-2004

1-800-221-0932 metraonline.com

REV. XX/XX/12

INSTXSVI-2004

1-800-221-0932 metraonline.com

REV. XX/XX/12

INSTXSVI-2004

1-800-221-0932 metraonline.com

REV. XX/XX/12

INSTXSVI-2004

1-800-221-0932 metraonline.com

REV. XX/XX/12

1997-2004 GM accessory Interface

• Provides accessory (12-volt 10-amp)

• Retains R.A.P. (Retained Accessory Power)

• High level speaker input

• Retains door woofers

• USB updatable

Chevrolet Corvette 1997-2004

XSVI-2004

1997-2004 GM accessory Interface

• Provides accessory (12-volt 10-amp)

• Retains R.A.P. (Retained Accessory Power)

• High level speaker input

• Retains door woofers

• USB updatable

Chevrolet Corvette 1997-2004

XSVI-2004

1997-2004 GM accessory Interface

• Provides accessory (12-volt 10-amp)

• Retains R.A.P. (Retained Accessory Power)

• High level speaker input

• Retains door woofers

• USB updatable

Chevrolet Corvette 1997-2004

XSVI-2004

1997-2004 GM accessory Interface

• Provides accessory (12-volt 10-amp)

• Retains R.A.P. (Retained Accessory Power)

• High level speaker input

• Retains door woofers

• USB updatable

Chevrolet Corvette 1997-2004

XSVI-2004

Wiring the XSVI-2004:

• Connect the Yellow wire to the radio’s 12-volt battery or memory wire.

• Connect the Black wire to the radio’s ground wire.

• Connect the Red wire to the ignition wire of the aftermarket radio.

• Connect the Orange/White wire to the illumination wire of the aftermarket radio.

If the aftermarket radio has no illumination wire, tape off the orange wire.

• Connect the Blue/White wire to the amp turn on wire of the aftermarket radio.

• Connect the White wire to the left front positive speaker output of the aftermarket radio.

• Connect the White/Black wire to the left front negative speaker output of the

aftermarket radio.

• Connect the Gray wire to the right front positive speaker output of the aftermarket radio

• Connect the Gray/Black wire to the right front negative speaker output of the

aftermarket radio.

• Connect the Green wire to the radio’s left rear positive speaker output.

• Connect the Green/Black wire to the radio’s left rear negative speaker output.

• Connect the Purple wire to the radio’s right rear positive speaker output.

• Connect the Purple/Black wire to the radio’s right rear negative speaker output.

Wiring the XSVI-2004:

• Connect the Yellow wire to the radio’s 12-volt battery or memory wire.

• Connect the Black wire to the radio’s ground wire.

• Connect the Red wire to the ignition wire of the aftermarket radio.

• Connect the Orange/White wire to the illumination wire of the aftermarket radio.

If the aftermarket radio has no illumination wire, tape off the orange wire.

• Connect the Blue/White wire to the amp turn on wire of the aftermarket radio.

• Connect the White wire to the left front positive speaker output of the aftermarket radio.

• Connect the White/Black wire to the left front negative speaker output of the

aftermarket radio.

• Connect the Gray wire to the right front positive speaker output of the aftermarket radio

• Connect the Gray/Black wire to the right front negative speaker output of the

aftermarket radio.

• Connect the Green wire to the radio’s left rear positive speaker output.

• Connect the Green/Black wire to the radio’s left rear negative speaker output.

• Connect the Purple wire to the radio’s right rear positive speaker output.

• Connect the Purple/Black wire to the radio’s right rear negative speaker output.

Wiring the XSVI-2004:

• Connect the Yellow wire to the radio’s 12-volt battery or memory wire.

• Connect the Black wire to the radio’s ground wire.

• Connect the Red wire to the ignition wire of the aftermarket radio.

• Connect the Orange/White wire to the illumination wire of the aftermarket radio.

If the aftermarket radio has no illumination wire, tape off the orange wire.

• Connect the Blue/White wire to the amp turn on wire of the aftermarket radio.

• Connect the White wire to the left front positive speaker output of the aftermarket radio.

• Connect the White/Black wire to the left front negative speaker output of the

aftermarket radio.

• Connect the Gray wire to the right front positive speaker output of the aftermarket radio

• Connect the Gray/Black wire to the right front negative speaker output of the

aftermarket radio.

• Connect the Green wire to the radio’s left rear positive speaker output.

• Connect the Green/Black wire to the radio’s left rear negative speaker output.

• Connect the Purple wire to the radio’s right rear positive speaker output.

• Connect the Purple/Black wire to the radio’s right rear negative speaker output.

Wiring the XSVI-2004:

• Connect the Yellow wire to the radio’s 12-volt battery or memory wire.

• Connect the Black wire to the radio’s ground wire.

• Connect the Red wire to the ignition wire of the aftermarket radio.

• Connect the Orange/White wire to the illumination wire of the aftermarket radio.

If the aftermarket radio has no illumination wire, tape off the orange wire.

• Connect the Blue/White wire to the amp turn on wire of the aftermarket radio.

• Connect the White wire to the left front positive speaker output of the aftermarket radio.

• Connect the White/Black wire to the left front negative speaker output of the

aftermarket radio.

• Connect the Gray wire to the right front positive speaker output of the aftermarket radio

• Connect the Gray/Black wire to the right front negative speaker output of the

aftermarket radio.

• Connect the Green wire to the radio’s left rear positive speaker output.

• Connect the Green/Black wire to the radio’s left rear negative speaker output.

• Connect the Purple wire to the radio’s right rear positive speaker output.

• Connect the Purple/Black wire to the radio’s right rear negative speaker output.

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS

Summary of content (2 pages)

PAGE 1
INSTXSVI-2004 INSTXSVI-2004 Chevrolet Corvette 1997-2004 XSVI-2004 Chevrolet Corvette 1997-2004 XSVI-2004 1997-2004 GM accessory Interface • • • • • 1997-2004 GM accessory Interface Provides accessory (12-volt 10-amp) Retains R.A.P. (Retained Accessory Power) High level speaker input Retains door woofers USB updatable • • • • • INSTALLATION INSTRUCTIONS Provides accessory (12-volt 10-amp) Retains R.A.P.
PAGE 2
INSTXSVI-2004 INSTXSVI-2004 INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Initializing the XSVI-2004: Initializing the XSVI-2004: When all the connections are completed plug the XSVI-2004 into the vehicle. Turn the ignition key to the “On” position for thirty seconds, then turn the key off. When all the connections are completed plug the XSVI-2004 into the vehicle. Turn the ignition key to the “On” position for thirty seconds, then turn the key off.