User Manual

ManualsBrandsAxxess ManualsAmplifier HarnessesMetra TYTO-01 JBL Amplifier Interface Harness

CAUTION!

All accessories, switches, climate

controls panels, and especially air bag indicator

lights must be connected before cycling the

ignition. Also, do not remove the factory radio

with the key in the on position, or while the

vehicle is running.

TYTO-01

INSTALLATION INSTRUCTIONS

INTERFACE FEATURES

INTERFACE COMPONENTS

TOOLS REQUIRED

• Cutting tool • Crimping tool • Tape

• Connectors (example: butt-connectors, bell

caps, etc.)

TABLE OF CONTENTS

Connections to be made ....................................2-3

Installing the TYTO-01 ............................................3

Testing the TYTO-01 ................................................3

Toyota ampliﬁed interface 2001-up*

• Provides accessory power (12-volt 10-amp)

• Used in ampliﬁed systems

• High level speaker input

• USB updatable

• Retains balance and fade

• TYTO-01 interface

• 16-pin harness with stripped leads

• 14-pin to 20-pin harness with stripped leads

*Visit AxxessInterfaces.com for up-to-date vehicle speciﬁc applications.

APPLICATIONS

See inside front cover

Summary of content (8 pages)

PAGE 1
TYTO-01 I N S TA L L AT I O N I N S T R U C T I O N S Toyota amplified interface 2001-up* TABLE OF CONTENTS Connections to be made.....................................2-3 Installing the TYTO-01.............................................3 Testing the TYTO-01.................................................3 *Visit AxxessInterfaces.com for up-to-date vehicle specific applications.
PAGE 2
APPLICATIONS Lexus ES330 ES300 IS300 LS430 RX330 RX350 RX400H SC430 2004-2006 2002-2003 2002-2005 2001-2006 2004-2006 2007-2009 2006-2008 2002-2010 Toyota 4-Runner (excludes Urban Runner) 2003-up Avalon 2005-up Camry 2007-up Corolla 2005-2011 FJ Cruiser 2011-up Highlander 2008-up Matrix 2005-2012 Prius 2004-2011 Prius (3rd gen/PHV) 2012-up Rav4 2004-up Sequoia 2005-up Sienna 2004-up Solara 2004-2008 Tacoma 2005-up Tundra 2006-up Tundra (double cab) 2004-2005 Venza (without NAV) 2009-up Venza (with NAV and
PAGE 3
CONNECTIONS TO BE MADE From the 20-pin harness, to the aftermarket radio: • Connect the Yellow wire to the 12-volt battery/memory wire. • Connect the Black wire to the ground wire. • Connect the Red wire to the accessory/ignition wire. INSTALLING THE TYTO-01 • With all connections completed to the aftermarket radio, plug the 20-pin harness into the vehicles wiring harness. • Reconnect the negative battery terminal. • Cycle the key, by turning the ignition on for 30 seconds.
PAGE 4
TYTO-01 I N S TA L L AT I O N I N S T R U C T I O N S IMPORTANT If you are having difficulties with the installation of this product, please call our Tech Support line at 1-800-253-TECH. Before doing so, look over the instructions a second time, and make sure the installation was performed exactly as the instructions are stated. Please have the vehicle apart and ready to perform troubleshooting steps before calling.
PAGE 5
TYTO-01 I N S T R U C C I O N E S D E I N S TA L AC I Ó N Toyota interfase amplificada 2001 y mas* INDICE Conexiones que se deben hacer.........................2-3 Instalación del TYTO-01...........................................3 Prueba del TYTO-01.................................................3 * Visite AxxessInterfaces.com para aplicaciones específicas de vehículos actualizadas.
PAGE 6
APLICACIONES Lexus ES330 ES300 IS300 LS430 RX330 RX350 RX400H SC430 2004-2006 2002-2003 2002-2005 2001-2006 2004-2006 2007-2009 2006-2008 2002-2010 Toyota 4-Runner (excluye Urban Runner) 2003 y mas Avalon 2005 y mas Camry 2007 y mas Corolla 2005-2011 FJ Cruiser 2011 y mas Highlander 2008 y mas Matrix 2005-2012 Prius 2004-2011 Prius (3rd gen/PHV) 2012 y mas Rav4 2004 y mas Sequoia 2005 y mas Sienna 2004 y mas Solara 2004-2008 Tacoma 2005 y mas Tundra 2006 y mas Tundra (doble cabina) 2004-2005 Venza (sin NA
PAGE 7
CONEXIONES QUE SE DEBEN HACER Del arnés de 20 pins al radio de mercado secundario: • Conecte el cable amarillo a la batería de 12 voltios/cable de memoria. • Conecte el cable negro con el cable de tierra. • Conecte el cable rojo con el cable de accesorios/ignición. INSTALACIÓN DEL TYTO-01 • Cuando termine de hacer todas las conexiones en el radio de mercado secundario, conecte el arnés de 20 pins en el arnés de cables del vehículo. • Reconecte la terminal negativa de la batería.
PAGE 8
TYTO-01 I N S T R U C C I O N E S D E I N S TA L AC I Ó N IMPORTANTE Si tiene dificultades con la instalación de este producto, llame a nuestra línea de soporte técnico al 1-800-253-TECH. Antes de hacerlo, revise las instrucciones por segunda vez y asegúrese de que la instalación se haya realizado exactamente como se indica en las instrucciones. Por favor tenga el vehículo desarmado y listo para ejecutar los pasos de resolución de problemas antes de llamar.