e13 036092 5-CHANNEL POWER AMPLIFIER Einbau- und Bedienungsanleitung Installation & Operating Instructions A470-170 Manual DEF.indd 1 12.09.
Inhalt Einleitung . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A B C D E F G H I Seite 4 Allgemeine Merkmale . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Anschlüsse & Bedienungselemente A470-170 . . . . . . 5/6 Montage-Tipps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Verkabelungs-Tipps . . . . . . . . . . . . . . . . . . . .
Index Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A B C D E F G H I Index Page 16 General Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Connections & Controls A470-170 . . . . . . . . . . . . . . 17-18 Amplifier Location & Mounting . . . . . . . . . . . . . . . . . . . 19 Wiring Tips . . . . . . . . . . . . . . . . . . . . . .
Einleitung Vielen Dank für das Vertrauen, das Sie uns mit dem Kauf dieses AXTONQualitätsprodukts entgegengebracht haben. Die AXTON Car Audio Verstärker wurden speziell für den Einsatz in mobilen Soundsystemen mit einer 12-Volt-Stromversorgung (mit negativer Chassis Masse) entwickelt. Damit Sie sich mit den technischen Eigenschaften und klanglichen Feinheiten Ihres Verstärkers vertraut machen können, empfehlen wir Ihnen, diese Einbau- und Bedienungsanleitung vor der Installation sorgfältig durchzulesen.
Anschlüsse & Bedienungselemente Rückseite AXTON A470-170 6 7 5 7 8 9 bl bm bn bo bp bq br bs bt bu cl cm cn co A470-170 1 A2180 2 3 A1350 A470-170 Manual DEF.indd 5 4 5 12.09.
B 1 ANschlüsse und BedienungSelemente GROUND/GND Anschlußklemme für die Verbindung zur Chassis- Masse (-12V). REMOTE/REM Anschlußklemme für die automatische Ein- bzw. Ausschaltung des Verstärkers über den ‚Amp‘- oder ‚Antenna-Remote‘Anschluß Ihres Steuergerätes. 2 3 +12 V Anschlußklemme für die direkte Verbindung zum positiven Batterie-Pol des Kfz. 4 FUSE Sicherungen für die interne Absicherung das Verstärkers gegen Überlastung und Fehlmanipulation.
C MONTAGE-TIPPS 1 Die Plazierung Ihres Verstärkers hat einen großen Einfluß auf die Ableitung der im normalen Betrieb entstehenden Wärme bzw. auf das eventuelle Ansprechen der automatischen Überhitzungssicherung des Gerätes. Aufgrund der Wärmeentwicklung des Verstärkers sollten Sie einen gut belüfteten Installationsort auswählen. Ideal für die Langzeitstabilität Ihres Verstärkers ist grundsätzlich jeder Montageort, an dem Luft ungehindert an den Kühlrippen vorbeiziehen kann.
4 Verwenden Sie die empfohlenen Stromkabelquerschnitte (siehe E). Zu geringe Querschnitte verringern die Ausgangsleistung, bewirken Verzerrungen und evtl. zu frühes Ansprechen der Übertemperatur-Sicherung. 5 Sichern Sie die +12V-Hauptleitung von der Batterie zum Verstärker ca. 20-30 cm nach der Batterie mit einer Hauptsicherung ab und verwenden Sie unbedingt Stromkabel mit leistungsbezogenem Querschnitt (Einzelheiten dazu finden Sie unter Abschnitt F, Anschluss und Einstellungen).
E AnschLUss DER A470-170 ACHTUNG: DAS -12V KABEL MUSS VOR BEGINN DER ANSCHLUSSARBEITEN UNBEDINGT VOM MINUSPOL DER BATTERIE ENTFERNT WERDEN! Empfohlene Stromkabel-Querschnitte für +12V und Masse (bei ca. 5 m +12V Kabel) sowie entsprechende HauptsicherungsWerte Modell Kabel-Querschnitt Hauptsicherung A470-170 20 mm² 60 A Idealerweise werden die AnschIüsse in dieser Reihenfolge durchgeführt: 1 2 Das Steuergerät muß ausgeschaltet und der Lautstärke-Regler ganz zurückgedreht sein.
F EINSTELLUNGEN A470-170 System-Verstärker-Konzept Die AXTON A470-170 ist eine 5-Kanal Endstufe. Mit einer einzigen A470-170 läßt sich auf einbaufreundliche Weise ein komplettes und klangstarkes 5-kanaliges Lautsprechersystem mit zwei Paar StereoSatelliten (vorn und hinten) und einem Subwoofer ansteuern. Die individuell regelbaren, integrierten Hochpass- bzw. Tiefpass-Filter der A470-170 erlauben es, die eingesetzten Lautsprecher genau den Einsatzbereich zuzuteilen, für den sie am Besten geeignet sind.
Satelliten-Grundregel 1 Das klanglich höherwertigere SatellitenSystem sollte immer vorne eingebaut werden. Satelliten-Grundregel 2 Ausgehend von ungefähr gleichen Durchmessern und gleicher Bauart des Front- und Heck-Lautsprecher-Systems sollte die Trennfrequenz der Front-Satelliten wenn möglich immer tiefer liegen als die der HeckSatelliten! Die zu wählende LOWPASS / LPF-Tiefpass-Trennfrequenz des Subwoofers sollte normalerweise im Bereich zwischen 50 und 90 Hz liegen. Stellen Sie den LOWPASS FREQ.
™ Drehen Sie nun den GAIN FRONT Regler Ihres Verstärkers langsam im Uhrzeigersinn auf, bis Sie einen tonal ausgewogenen Klangcharakter erzielt haben. Eine leichte Bassbetonung ist vorzuziehen, da sie von den Fahrgeräuschen wieder „überdeckt‘ wird. ™ Drehen Sie nun den GAIN REAR Regler langsam auf, bis Sie mit den Heck-Lautsprechern einen guten ‚Rear-Fill‘ und ein homogenes Gesamtklangbild erreicht haben.
G Störungsbehebung Problem Ursache Kein Musiksignal auf den Lautsprechern ● und Status-LED leuchtet rot oder gar nicht ● ● ● ● ● ● + 12 V oder GROUND (Masse) oder “Remote“-Kabel nicht (richtig) angeschlossen Sicherung des Verstärkers durchgebrannt Hauptsicherung an der Batterie durchgebrannt Kurzschluß auf einem der Lautsprecherausgänge DC/Gleichspannung am Ausgang Überlastung des Verstärkers Überhitzung des Verstärkers Ein Sirren das mit der ● Motordrehzahl zu- oder abnimmt ● Schlechter M
H Technische DateN AXTON 5-Kanal System Verstärker Sinusleistung mono/stereo (an 13.8V) Satelliten (Front+Rear) an 4 Ohm (2 x stereo) min. Subwoofer (mono) an 4 Ohm min. Sinusleistung mono/stereo (an 13.8V) Satelliten (Front+Rear) an 2 Ohm (2 x stereo) Subwoofer (mono) an 2 Ohm Frequenzgang (Sub+Front+Rear) Verzerrungen/Klirr (THD) an 4 Ohm Rauschabstand Kanaltrennung Flankensteilheit Hochpass und Tiefpass Regelbereich Hochpass Regelbereich Tiefpass Regelbereich Subsonic CH 5 Empf.
A470-170 Manual DEF.indd 15 12.09.
Introduction Thank you for purchasing this AXTON quality audio component. The AXTON amplifier series has been developed for the use with mobile sound systems using 12 Volts negative chassis ground power supply. The amplifiers may be used in combination with almost any brand and type of head unit and speakers in cars, vans, boats etc. and when installed correctly, AXTON amps will produce exceptional results.
Connections & Controls REAR-PANEL AXTON A470-170 6 7 5 7 89 bl bm bn bo bp bq br bs bt bu cl cm cn co A470-170 1 A2180 2 3 A1350 A470-170 Manual DEF.indd 17 4 17 12.09.
B CONNECTIONS AND CONTROLS A470-170 1 GROUND/GND Power connection terminal to chassis ground or negative terminal of car battery (-12 V). 2 REMOTE/REM Remote switching contact for the automatic (remote) turn-on/turn-off of the power amplifier from the head-unit's remote (or antenna control) lead. 3 4 +12 V Power connection terminal to positive terminal of car battery.
C Amplifier LOCATION & MOUNTING 1 The mounting location of the power amplifier will have a large effect both on its ability to dissipate the heat generated during normal operation through the heat sink and on the possible triggering of its internal overheat protection shut-off circuit. Any mounting position allowing for a good air stream across the cooling fins of the amplifiers heatsink will improve cooling and long-term stability dramatically.
5 Make sure you are using a main fuse protection for the +12Vpower input of the amplifier within max. 30 cm of the car battery and power cables with an amperage adequate cross-section and main fuse (for details see section E: „Connecting“). 6 The GROUND/GND cable (-12V) should have the same crosssection as the +12V power cable. Make sure to get a good chassis ground contact, because poor ground contacts are the cause for most power problems with car audio installations.
E CONNECTING a470-170 IMPORTANT: DISCONNECT THE -12V MAIN POWER CABLE FROM YOUR CAR BATTERY BEFORE ANY CONNECTING WORK IS CARRIED OUT! Recommended Power Cable Cross-Sections and Main Fuse Values (for +12V and Ground cable based on 5m +12 V cable) Model Cross-Section Main Fuse A470-170 20 mm² 60 A 3 4 Remote lead connection from head-unit to amplifier. Speaker cables to respective speakers or passive crossovers. Make sure to maintain polarity! "" to "" and "" to "".
F CONTROLS & ADJUSTMENTS A470-170 5-Channel System Amplifier The AXTON A470-170 is a powerful 5-channel system amplifier. One single A470-170 allows for an easy-to-install, speaker-dedicated amplification of a complete 5-channel speaker system, i.e. with two stereo pairs of independently controlled satellite speakers (front and rear) and one mono subwoofer.
Satellite rule 1 The better sounding satellite system should always be installed in the front of the vehicle. Satellite rule 2 Based on identical speaker diameters and quality of the front and rear satellites, the crossover cut-in frequency of the front satellites should usually be set lower than the highpass frequency of the rear satellites. The LPF / LOWPASS SUB cut-off frequency for the subwoofer should usually be set in between 50 and 90 Hz.
™ Start turning up the REAR GAIN control (3CH/4CH) clockwise until you feel to you have reached an appropriate ‚rear fill‘ in the back of the car, so that the overall in-car sound becomes smooth and balanced. ™ Finally, you may want to do some fine-tuning on the different highpass and lowpass frequencies selected. It is recommended to start fine-tuning with the subwoofer (LOWPASS SUB) frequency.
G TROUBLESHOOTING Problem Cause No music signal on loudspeakers and STATUS-LED on amp is red or off ● + 12 V and/or GROUND (GND/ -12V) and/or “Remote” line not (properly) connected ● Fuse on amplifier or distributor blown ● Main Fuse on car battery side blown ● Short-circuit on any of the speaker outputs ● DC voltage at speaker outputs ● Amplifier overload ● Amplifier overheated A high-pitched buzzing sound ● Bad ground (GND) conntact of amplifier or head unit in- or decreasing with engine speed ● Ins
H Specifications AXTON 5-Channel System Amplifier A470-170 Rated power output mono/stereo (at 13.8V) Satellites (Front+Rear) at 4 ohms (2 x stereo) min. Subwoofer (mono) at 4 ohms min. Rated power output mono/stereo (at 13.
A470-170 Manual DEF.indd 27 12.09.
Introduction Merci d’avoir acheté cet amplificateur AXTON Cette gamme d’amplificateurs a été spécialement développée pour une utilisation en milieu automobile utilisant une alimentation 12 V avec masse au châssis. Ces amplificateurs peuvent être utilisés en combinaison avec tout autre composants audio disponible sur le marché tant au niveau hautparleurs que sources. Installés correctement, les appareils AXTON vous procureront un niveau de reproduction sonore exceptionnelle.
Connections et réglages Face avant AXTON A470-170 6 7 5 7 89 bl bm bn bo bp bq br bs bt bu cl cm cn co A470-170 1 A2180 2 3 A1350 A470-170 Manual DEF.indd 29 4 29 12.09.
B Connections et réglages A470-170 1 Masse: à connecter au châssis du véhicule ou à la borne négative de la batterie. 2 Remote: signal de mise en marche de l’amplificateur, à connecter à une sortie télécommandée de la source. 3 4 5 bs sorties avant: bornier haut parleur avant. Impédance sorties subwoofer: bornier haut parleur subwoofer. Indicateur de mise en protection: ce voyant (rouge) indique que l’amplificateur a enclenché une de ces protections suite à un problème.
C placement de l’amplificateur 1 L’emplacement de l’amplificateur dans le véhicule a une grosse incidence sur sa capacité à dissiper la température qu’il génère lors de son fonctionnement. Il peut en résulter un enclenchement excessif de la protection thermique. La position d’installation doit permettre une bonne circulation de l’air au travers des ouies d’aération. L’emplacement choisis doit être donc bien ventilé, à l’abris de la poussière et de l’humidité.
5 Il est impératif de placer un fusible principal au maximum à 30 cm de la batterie. L’ampérage de ce fusible est déterminé par la consommation de l’installation globale. (voir chapitre E) 6 Le câble de masse (GND) doit être de même section que le câble positif ( il y circule le même courant). Le point de masse sur le châssis doit être le meilleur possible et bien nettoyé pour assurer un bon contact électrique.
E Connecter le A470-170 Important : Le câble d’alimentation 12 v ne sera connecté à la batterie qu’a la fin complète de l’installation. 3 4 Le câble d’alimentation recommandé pour une longueur de 5 m aura une section de 20 mm2. 5 Le fusible principal pour cet amplificateur sera d’au moins 60 A Il est recommandé de câbler votre amplificateur comme suit : 1 2 assurez vous que la source est hors service et que sont contrôle de volume est au minimum.
F Contrôles et réglages A470-170 Amplificateur 5 canaux L’ AXTON A470-170 est un amplificateur 5 canaux performant. Un seul appareil vous permet d’alimenter un système de 5 haut-parleurs complet (avant, arrière et subwoofer). Les filtres intégrés indépendants vous permettent d’utiliser chaque hautparleur de façon optimum.
Règle 1 : Les haut-parleurs de meilleur qualité sont installés à l’avant du véhicule Il est recommandé de procéder aux réglages de sensibilité de gain d’amplification afin de correspondre à la séquence décrite ci-après : Règle 2 : en se basant sur des haut-parleurs de diamètres et de qualité identiques, la fréquence de coupure des hps avant sera tou jours réglée plus bas que la fréquence de coupure du filtre passe-haut des hps arrières.
G défauts / solutions Problème Cause Pas de musique, Voyant sur l’amplificateur éteint. ● ● ● ● ● Parasites aigus en rythme avec Le moteur ● mauvaise masse sur l’amplificateur et/ou l’autoradio. ● câble RCA de mauvaise qualité (blindage insuffisant).
H Spécifications AXTON amplificateur 5 canaux Puissance de sortie @ 13.8V Satellites (av/ar) @4 ohms stéréo Subwoofer (mono) @ 4 ohms Puissance de sortie @ 13.
I Warranty Certificate Please keep this Warranty Certificate along with the sales slip/proof of purchase. Limited Warranty This AXTON product is fully warranted against defective materials or workmanship for a period of 2 YEARS from date of purchase at retail. Warranty will only be granted if the warranty certificate is presented fully completed with model, serial number (if applicable), purchaser´s address, purchasing date and dealer stamp together with the original sales slip or proof of purchase.
I Garantiekarte Bitte bewahren Sie diese Garantiekarte zusammen mit Ihrer Kaufbestätigung auf. Seriennummer Modell Adresse des Händlers Garantiebestimmungen AXTON gewährleistet auf das in dieser Karte aufgeführte AXTON-Produkt für den Fall von Material- oder Herstellungsfehlern 2 Jahre Garantie beginnend ab Kaufdatum im Fachhandel. Garantieansprüche können nur mit einer korrekt und vollständig ausgefüllten Garantiekarte zusammen mit dem Original-Kaufbeleg geltend gemacht werden.
A470-170 Manual DEF.indd 40 12.09.