User Manual

ManualsBrandsAxis ManualsAudio & VideoP1375-E network surveillance camera

Table Of Contents

AXISP1375-ENetworkCamera

UserManual

Summary of content (23 pages)

PAGE 1
AXIS P1375-E Network Camera User Manual
PAGE 2
AXIS P1375-E Network Camera Table of Contents Product overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Find the device on the network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Access the device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Verify that no one has tampered with the firmware . . . . . . . . . . . . . . . . . . . . About secure passwords . . . . . . . . . . . . . . . . . . . . . .
PAGE 3
AXIS P1375-E Network Camera Product overview Product overview 1 2 3 4 5 6 7 8 9 10 11 12 Weather shield Window Intrusion alarm magnet Safety wire IK10 tool Intrusion alarm sensor Cable cover Spring loaded thumb screw (4x) Optic unit Zoom puller Lock screw for focus ring Focus ring NOTICE TICE NO Do not lift the product in the cable cover.
PAGE 4
AXIS P1375-E Network Camera Product overview 13 14 15 16 17 18 19 20 21 22 23 I/O connector RS485/422 connector Power connector Network connector (PoE) microSD card slot Audio in Audio out Control button Status LED Cable gasket M20 (2x) Iris connector 24 Illuminator connector 4
PAGE 5
AXIS P1375-E Network Camera Find the device on the network Find the device on the network To find Axis devices on the network and assign them IP addresses in Windows®, use AXIS IP Utility or AXIS Device Manager. Both applications are free and can be downloaded from axis.com/support For more information about how to find and assign IP addresses, see the document How to assign an IP address and access your device on the device page at axis.com Access the device 1.
PAGE 6
AXIS P1375-E Network Camera Find the device on the network 3. Click Create login. The password has now been configured.
PAGE 7
AXIS P1375-E Network Camera Setup Setup About the product's built-in help You can access the built-in help from the product’s webpage. The help provides more detailed information on the product’s features and their settings. Replace the lens 1. Stop all recordings and disconnect power from the product. 2. Disconnect the lens cable and remove the standard lens. 3. Attach the new lens and connect the lens cable. 4. Reconnect the power. 5.
PAGE 8
AXIS P1375-E Network Camera Setup Hide parts of the image with privacy masks What is a privacy mask? A privacy mask is a user-defined area that covers a part of the monitored area. In the video stream, privacy masks appear either as blocks of solid color or with a mosaic pattern. You’ll see the privacy mask on all snapshots, recorded video, and live streams. You can use the VAPIX® application programming interface (API) to turn off the privacy masks.
PAGE 9
AXIS P1375-E Network Camera Setup Select exposure mode There are different exposure mode options in the camera that adjusts aperture, shutter speed, and gain to improve image quality for specific surveillance scenes. Go to Settings > Image > Exposure and select between the following exposure modes: • For most use cases, select Automatic exposure. • For environments with certain artificial lighting, for example fluorescent lighting, select Flicker-free.
PAGE 10
AXIS P1375-E Network Camera Setup 2. Adjust the size and placement of the rectangle in the camera’s live view around the area of interest, for example where the license plates of passing cars are expected to appear. You can then see the number of pixels represented by the sides of the rectangle. Note You can use an object of a known size in the view as a reference to decide how much resolution is needed for recognition.
PAGE 11
AXIS P1375-E Network Camera Setup Image with WDR. Note WDR may cause artifacts in the image. Find out more about WDR and how to use it at axis.com/web-articles/wdr About overlays Overlays are superimposed over the video stream. They are used to provide extra information during recordings, such as a timestamp, or during product installation and configuration.
PAGE 12
AXIS P1375-E Network Camera Setup Note If you update the overlay text it will be automatically updated on all video streams dynamically. Choose video compression format Decide which compression method to use based on your viewing requirements, and on the properties of your network. The available options are: Motion JPEG Note To ensure support for the Opus audio codec, the Motion JPEG stream is always sent over RTP.
PAGE 13
AXIS P1375-E Network Camera Setup Note Web browsers do not support H.265 decoding. Use a video management system or application supporting H.265 decoding. Set up network storage To store recordings on the network, you need to set up network storage: 1. Go to Settings > System > Storage. 2. Click Setup under Network storage. 3. Enter the IP address of the host server. 4. Enter the name of the shared location on the host server. 5.
PAGE 14
AXIS P1375-E Network Camera Setup 3. Select which Action the camera should perform when the conditions are met. Note If you make changes to an active action rule, the action rule needs to be restarted for the changes to take effect. Record video when the camera detects motion This example explains how to set up the camera to start recording to the SD card five seconds before it detects motion and to stop one minute after. Make sure the AXIS Video Motion Detection application is running: 1.
PAGE 15
AXIS P1375-E Network Camera Troubleshooting Troubleshooting If you can’t find what you’re looking for here, try the troubleshooting section at axis.com/support Reset to factory default settings Important Reset to factory default should be used with caution. A reset to factory default resets all settings, including the IP address, to the factory default values. To reset the product to the factory default settings: 1. Disconnect power from the product. 2.
PAGE 16
AXIS P1375-E Network Camera Troubleshooting Upgrade the firmware Important Preconfigured and customized settings are saved when the firmware is upgraded (provided that the features are available in the new firmware) although this is not guaranteed by Axis Communications AB. Important Make sure the product remains connected to the power source throughout the upgrade process.
PAGE 17
AXIS P1375-E Network Camera Troubleshooting The device cannot be accessed from a browser Cannot log in When HTTPS is enabled, ensure that the correct protocol (HTTP or HTTPS) is used when attempting to log in. You may need to manually type http or https in the browser’s address field. If the password for the user root is lost, the device must be reset to the factory default settings. See Reset to factory default settings on page 15.
PAGE 18
AXIS P1375-E Network Camera Troubleshooting • Rotating the lens manually will result in better performance compared to rotating the image from the GUI. • Access by large numbers of Motion JPEG or unicast H.264 clients affects the bandwidth. • Simultaneous viewing of different streams (resolution, compression) by different clients affects both frame rate and bandwidth. Use identical streams wherever possible to maintain a high frame rate. Stream profiles can be used to ensure that streams are identical.
PAGE 19
AXIS P1375-E Network Camera Specifications Specifications To find the latest version of the product’s datasheet, go to the product page at axis.com and locate Support & Documentation. LED Indicators Note • The Status LED can be configured to be unlit during normal operation. To configure, go to Settings > System > Plain config. See the online help for more information. • The Status LED can be configured to flash while an event is active. • The Status LED can be configured to flash for identifying the unit.
PAGE 20
AXIS P1375-E Network Camera Specifications This product supports microSD/microSDHC/microSDXC cards. For SD card recommendations, see axis.com microSD, microSDHC, and microSDXC Logos are trademarks of SD-3C LLC. microSD, microSDHC, microSDXC are trademarks or registered trademarks of SD-3C, LLC in the United States, other countries or both. Buttons Control button The control button is used for: • Enabling the Focus Assistant. Press and very quickly release the Control button.
PAGE 21
AXIS P1375-E Network Camera Specifications Digital output - For connecting external devices such as relays and LEDs. Connected devices can be activated by the VAPIX® Application Programming Interface or from the product’s webpage. Function Pin DC ground 1 DC output 2 Can be used to power auxiliary equipment. Note: This pin can only be used as power out.
PAGE 22
AXIS P1375-E Network Camera Specifications RS485/RS422 connector Two 2-pin terminal blocks for RS485/RS422 serial interface used to control auxiliary equipment such as pan-tilt devices.